GIGABYTE BRIX Extreme Ultra Compact PC Kit

Introduction

This document provides a quick start guide for the GIGABYTE BRIX Extreme Ultra Compact PC Kit. It covers system information, appearance, hardware installation, and BIOS setup.

Copyright © 2022 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.

Disclaimer: Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to specifications may be made without prior notice. No part of this manual may be reproduced without GIGABYTE's written permission.

Support Information

For warranty information, tested component lists, drivers, BIOS updates, and product support, please visit the GIGABYTE support website:

https://www.gigabyte.com/support-downloads/customer-service

Additional support resources are available at: https://www.gigabyte.com

Safety and Regulatory Information

Grounding: The product must be grounded via the adapter's power cord connected to a grounded socket.

Battery Safety: Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled according to local environmental regulations.

Component Handling: Before opening the chassis to exchange internal components, power off the device and allow it to cool for at least 10 minutes.

Power Adapter: Use only the included GIGABYTE GB-BEi Power Adapter. Failure to do so may violate regulations and pose safety hazards.

General Safety: Follow all safety guidelines provided in the manual to avoid damage or injury.

Conventions Used in this Guide

• NOTE!: Provides additional information related to the current topic.
• CAUTION!: Gives precautionary measures to avoid possible hardware or software problems.
• WARNING!: Alerts to potential damage from specific actions.
• Languages Icon (?): Indicates text is translated into different languages.

Symbol Statements

End-of-Life Disposal: This product should not be treated as household waste. It must be handed over to an applicable collection point for recycling of electrical and electronic equipment.

FCC Compliance: This device complies with Part 15 of the FCC Rules. Operations are subject to two conditions: no harmful interference, and acceptance of any interference received.

Hot Surface Warning (?): CAUTION! Hot Surface. Do not touch.

HDMI: HDMI and the HDMI Logo are trademarks of HDMI Licensing LLC.

Restricted Substances Information

This table indicates the presence of restricted substances in components, adhering to RoHS standards.

Notes:

○: Percentage content of restricted substance does not exceed the reference value.

—: Restricted substance is an exemption item.

Chapter 1: System Information

1-1 Installation Precautions

ESD Warning: System components are sensitive to Electrostatic Discharge (ESD). Follow precautions:

• Do not remove or break motherboard S/N or warranty stickers.
• Always disconnect AC power before installation/removal of components.
• Ensure hardware components are connected tightly.
• Avoid touching metal leads/connectors on the motherboard.
• Use an ESD wrist strap or touch a metal object to discharge static electricity.
• Place motherboard on an antistatic pad or shielding container.
• Ensure power supply is turned off before unplugging.
• Verify power supply voltage setting.
• Ensure all cables and power connectors are properly connected.
• Prevent screws from contacting motherboard circuits.
• Ensure no leftover screws or metal parts are inside the casing.
• Do not place the system on uneven surfaces or in high-temperature environments.
• Do not turn on power during installation to avoid damage or injury.
• Consult a certified technician if uncertain about installation steps.

1-2 Product Specifications

System Dimension: 52 mm x 134.2 mm x 139.1 mm (2.0" x 5.3" x 5.4")

CPU Options:

• GB-BEi7-1260 / GB-BEi7H-1260 / GB-BEi7HS-1260: 12th Gen Intel Core i7-1260P, 12 Cores (4P+8E), 16 Threads, 12MB L2 Cache, 2.1GHz-4.7GHz, 28W
• GB-BEi5-1240 / GB-BEi5H-1240 / GB-BEi5HS-1240: 12th Gen Intel Core i5-1240P, 12 Cores (4P+8E), 16 Threads, 12MB L2 Cache, 1.7GHz-4.4GHz, 28W
• GB-BEi3-1220 / GB-BEi3H-1220: 12th Gen Intel Core i3-1220P, 10 Cores (2P+8E), 12 Threads, 12MB L2 Cache, 1.5GHz-4.4GHz, 28W

• Motherboard Size: 125mm x 128.8 mm (4.9" x 5.1")
• Memory: 2 x SO-DIMM DDR4 slots, up to 3200MHz, Max 64GB
• LAN: 2.5G LAN (Intel i225V)
• Video: Intel Iris Xe Graphics, 96EU
• Wi-Fi Card: Intel WiFi-6E / BT 5.2 Module
• Audio: Realtek ALC897 HD audio
• Storage: 1 x PCI-e Gen3 x4 / SATA M.2 2280 slot, 1 x 2.5" HDD/SSD (7.0mm thick, 6 Gbps SATA 3)
• Mini DP Resolution (Max.): 2x HDMI2.0a with HDCP 2.2, Max Res 3840x2160@60Hz; USB 4.0 Type-C DP 1.4a, Max Res 3840x2160@60Hz
• HDMI Resolution (Max.): 1x HDMI2.1 with HDCP 2.2, Max Res 7680x4320@60Hz; 1x HDMI2.0a with HDCP 2.2, Max Res 3840x2160@60Hz
• VESA: Mounting Bracket Included

1-3 Package Contents

1-3-1 GB-BEi Bare-bone

The package includes the bare-bone unit. It does NOT include M.2 (2280) SSD, 2.5" HDD, or SO-DIMM memory.

1-3-2 VESA Mount

Includes VESA bracket and 6 screws.

1-3-3 135W Adapter & Power Cord

Use the included power cord only with this product. Do not use it with other products.

1-3-4 Quick Start Guide

This document.

Chapter 2: System Appearance

2-1 Front View

2-1-1 Standard

Diagram Description:

• 1. Headphone/Microphone Jack
• 2. USB 3.2 Gen2 with Type-C Port
• 3. 3 x USB 3.2 Gen2 Type A Ports
• 4. Power Button

2-1-2 HDD / Super

Diagram Description: (Same as 2-1-1)

2-2 Rear View

2-2-1 Standard

Diagram Description:

• 5. Mini DisplayPort
• 6. HDMI 2.1 Port
• 7. HDMI 2.0b Port
• 8. 2 x USB 2.0 Type A Ports (5V/0.5A)
• 9. USB 3.2 Gen2 with Type-C (Alt Mode Thunderbolt 4, 5V/3A)
• 10. RJ-45 Port (10/100/1000/2500Mbps)
• 11. Kensington Lock Slot
• 12. DC-In Port

2-2-2 HDD / Super

Diagram Description: (Same as 2-2-1)

2-2-3 Installed GC-CMM-DLCS upgrade kit

Diagram Description: (Similar to 2-2-1, with additional ports 13 & 14 for upgrade kit)

• 13. Console Port (Optional Upgrade Kit)
• 14. RJ-45 Port (Optional Upgrade Kit)

2-3 Left View

2-3-1 Standard

Diagram Description: Shows cooling vents.

2-3-2 HDD / Super

Diagram Description: Shows cooling vents.

2-4 Right View

2-4-1 Standard

Diagram Description: Shows cooling vents.

2-4-2 HDD / Super

Diagram Description: Shows cooling vents.

2-5 Bottom View

Diagram Description:

• 16. VESA Bracket Screw Holes

2-6 PIN Definition

Diagram Description:

• A: M.2 2280 SSD Connector
• B: DDR SO-DIMM slot
• C: Wi-Fi Connector
• D: SATA connector for 2.5" HDD or LAN/COM/M.2 Upgrade Kit (HDD/Super SKU)

Chapter 3: System Hardware Installation

Pre-installation Instructions

ESD Warning: Handle components with care to prevent ESD damage. Always disconnect power before working. Use ESD wrist strap or ground yourself. Handle boards by edges only. Leave components in static-proof packaging until needed.

3-1 Removing the Bottom Cover

Instructions:

1. Remove the screw securing the chassis side cover.
2. Slide the cover towards the rear and remove it.

3-2 Installing the M.2 SSD

Instructions:

1. Remove the small screw and thermal plate from the M.2 SSD slot A.
2. Carefully insert the M.2 SSD into slot A.
3. Secure the thermal plate and M.2 SSD with the removed screw.

3-3 Installing the Memory

Guidelines: Ensure system compatibility. Use matching memory modules. Always disconnect power before installation. Memory modules install in one direction.

Instructions:

1. Carefully insert SO-DIMM memory modules.
2. Push down until modules click into place.
3. Repeat for the second module if applicable.
4. Push down until modules click into place.

3-4 Remove the Wireless Module

Instructions:

1. Disconnect antennas by lifting clips.
2. Remove the center screw.
3. Carefully pull the wireless module from the slot.

3-5 Installing the VESA Bracket

Note: VESA screws are 5.0 mm M3 type.

Instructions:

1. Remove both side covers.
2. Slide the hard disk drive into the slot.
3. Mount with two screws on each side.

3-6 Installing Additional SATA 6Gbps HDD (2.5" HDD)

Note: HDD thickness must be less than 7mm.

Instructions:

1. Unscrew and remove the HDD bracket.
2. Disconnect the SATA cable.
3. Screw the HDD and bracket together with four screws.
4. Connect the HDD with the SATA cable.
5. Connect the cable to the SATA connector on the motherboard.
6. Reinstall the bracket with HDD to the bottom panel.

3-7 Installing LAN/COM/M.2 Upgrade Kit

Note: System does not support both LAN/COM kit and 2.5" HDD. M.2 module cannot have a thermal plate due to space limitations.

Instructions:

1. Unscrew and remove the bracket.
2. Disconnect the SATA cable.
3. Install the upgrade kit board onto the bottom panel with four screws.
4. Connect the upgrade kit cable to the board.
5. Connect the cable to the SATA connector on the motherboard.
6. Reinstall the bracket with the upgrade kit to the bottom panel.

Chapter 4: BIOS Setup

4-1 USB Power On Function

Allows device power-on via USB, useful when mounted behind a display or TV.

Note: Windows requires an additional patch ('USB Power-On Patch') available on the GIGABYTE website for this functionality.

Instructions to enable USB Power On:

1. Press "Del" during startup to enter BIOS.
2. Select "Chipset" from the menu.
3. Manually configure "USB S5 Wakeup Support" to "Enable".
4. Press F4 to Save and Exit.