Driklux Watch Winder and Fingerprint Lock Manual

Watch Winder Manual

Preparation Before Use

First, wind the automatic watch by shaking it for 60-70 times to ensure it has at least half of its kinetic energy. Then, place it in the watch winder after calibrating the time.

Gear Selection Instructions

Refer to the watch's manual or consult the seller for the correct winding direction. Most automatic mechanical watches use clockwise winding. Test with clockwise winding for 48 hours. If the watch functions correctly, clockwise winding is suitable. If the watch stops or slows down, hand-wind it until it has sufficient kinetic energy, then try counter-clockwise or alternating winding for 48 hours. Observe the watch's operation to determine the optimal winding direction. If multiple watches are used on the same turntable, they may require different winding directions.

Precautions for Use

• Place or remove watches only when the winder is stopped. Avoid taking watches while the motor is running to prevent damage.
• Do not use batteries and the adapter simultaneously. Use either the adapter or batteries. Nanfu batteries are not recommended.
• Use only the original power adapter to avoid circuit damage due to voltage or current differences.
• The watch winder consumes low power and can be used continuously. However, for continuous use exceeding 30 days, turn off the main power supply and let the winder rest for 12 hours.
• A single turntable can support up to 450g. Do not exceed the motor's load-bearing capacity.
• The watch winder operates optimally at temperatures between -15 degrees Celsius.

Mode 5 Manual

Structural Diagram: Includes DC outlet, Main switch, Door Sensor switch (on some models), and LED Light switch (on some models).

Rotation Modes:

• Mode 1: Operation On/Off.
• Mode 2: Clockwise rotation for 2 minutes, rest for 6 minutes, repeat.
• Mode 3: Counter-clockwise rotation for 2 minutes, rest for 6 minutes, repeat.
• Mode 4: Alternating direction. Rotate clockwise for 2 minutes, rest for 6 minutes. Rotate counter-clockwise for 2 minutes, rest for 6 minutes. Repeat cycle.
• Mode 5: Alternating direction. Rotate for 5 minutes in one direction, then rotate in the opposite direction for 5 minutes. Repeat continuously for 3 hours, then rest for 9 hours. After 9 hours, the cycle restarts.

Door Sensor: When enabled, the motor stops when the cover is opened and resumes when closed.

LED Light: Indicates when the LED light is on.

TPD 9 Manual

Structural Diagram: Similar to Mode 5, includes DC outlet, Main switch, Door Sensor switch, and LED Light switch.

TPD (Turns Per Day) Settings:

• Work Time: 12 hours of operation, followed by 12 hours of rest. Rotors turn and stop to reach the set number of turns.
• 650 TPD: Rotates 650 times per day. Direction is user-selectable.
• 750 TPD: Rotates 750 times per day. Direction is user-selectable.
• 850 TPD: Rotates 850 times per day. Direction is user-selectable.
• 1000 TPD: Rotates 1000 times per day. Direction is user-selectable.
• 1950 TPD: Rotates 1950 times per day. Direction is user-selectable.
• Auto: Alternating direction. Rotate for 2 minutes in one direction, rest for 6 minutes. Rotate for 2 minutes in the opposite direction, rest for 6 minutes. Repeats cycle without a 12-hour rest period.

Orientation: Clockwise (), Counter-clockwise (), Alternating ().

Operation: When "00" is selected, pressing the start button initiates all watches working in the last set TPD mode sequentially.

Indicator Lights:

• LED: Indicates lighting is on.
• UVC: Indicates sterilization lamp is on (automatically turns off after 10 minutes).
• Light: Indicates rainbow lights are on.

Fingerprint Lock Manual

This manual applies to models with fingerprint lock functionality.

CTRL

Experience Mode: Any fingerprint can unlock the product.

Unlock Verification Mode: Successful verification results in a blue light for 2 seconds before the lock closes. Failure results in 3 rainbow flashes.

Fingerprint Entry Mode

The system supports 2 administrators and up to 18 users.

First Fingerprint Input (Administrator): Long press the fingerprint sensor for 7 seconds. After verification (approx. 5 seconds), a pink light flashes, indicating entry mode. Press the sensor with the desired fingerprint. Each successful press is indicated by a blue light flash. The first successful input becomes the administrator fingerprint.

Second Fingerprint Entry (Administrator): Long press the sensor for 7 seconds. After verification, a slow blue light flashes 3 times. Release the finger. A pink light flashes once. Use the first administrator's fingerprint for confirmation. Each effective press is indicated by a blue light flash; invalid presses show a red light flash. Six effective presses are required. A slow double blue light flash indicates successful entry. This fingerprint becomes the second administrator.

User Fingerprint Entry: Long press the sensor for 7 seconds. After verification, a slow blue light flashes 3 times. Release the finger. Press the administrator's fingerprint for confirmation. A pink light flash indicates success. Press the user's fingerprint. Each effective press shows a blue light flash; invalid presses show a red light flash. Six effective presses are required. A slow double blue light flash indicates successful entry.

Be Careful:

• Administrator verification: Pink light flashes on success, red light on failure. Three consecutive failures trigger a red light flash and exit.
• Fingerprint entry state: Three consecutive invalid presses trigger a red light flash and exit.
• If no fingerprint is detected within 5 seconds, a red light flash indicates failure and exit.
• It is recommended to use different fingers for the two administrators.
• Use only one finger for each fingerprint input attempt.
• All modes exit to the sleep standby state.

I. Part Names

A. USB type-c port: Charging the fingerprint lock.

B. Lock Body: Zinc alloy + PC.

C. Fingerprint panel: Finger identification area.

D. Locking hole: Lock/Unlock mechanism.

E. Indicated light: Shows status.

II. Set Administrator Account for the First Time

1. Press the panel for 3 seconds until the blue light is on.
2. Collect the same finger 10 times from different directions.
3. Blue light on indicates successful setting. Red light on indicates failure.
4. 10 successful fingerprint collections result in a long beep and successful administrator account setting.

Remarks:

• Charge the lock if there is no electricity.
• The first fingerprint is the administrator's.
• Subsequent fingerprints (user accounts) require administrator confirmation.
• Users should collect as many sets of fingerprints as possible.

III. Second to Tenth User Fingerprint Entry

1. Press the panel for 3 seconds; blue and red lights flash.
2. Identify administrator's fingerprint; blue light is on.
3. Collect the user's finger 10 times from different directions.
4. Red light on indicates setting failed.
5. 10 successful collections result in a long beep and successful user account setting.

IV. Delete

1. Press the panel for 6-10 seconds.
2. Red light flashes; identify administrator's fingerprint.
3. Red light stays on with a long beep for successful deletion.
4. Red light flashes indicate deletion failure; re-identify the administrator's fingerprint or restart.

V. Unlock Way

Unlock using either the Fingerprint () or the Key ().

VI. Low Power

When voltage is 3.5V or lower, the fingerprint panel and green indicator flash. Charge the device.

VII. Restore Factory Settings

With the lock powered on, insert the electronic key into the charging port and press any finger on the pad. A green light flashes for 2 seconds, resetting all fingerprints. Any finger can then unlock the lock.

VIII. Specification

Delete Mode

Press and hold the fingerprint head for 17 seconds. After verification, the blue light flashes slowly 3 times. Continue pressing, and a red light flashes slowly for 3 times after 10 seconds. Release the finger when the red light flashes. Press the administrator's fingerprint; a pink light flash indicates success. Two successful administrator verifications result in quick blue light flashes, indicating memory cleared and settings restored.

• Administrator verification failure: Red light flashes once. Continuous failures (over 3 times) trigger 4 red light flashes, indicating deletion failure and exit.
• No fingerprint detected for over 5 seconds: 4 red light flashes indicate deletion failure and exit.
• All modes exit to the sleep standby state.
• For after-sales service, the administrator's fingerprint must be used to delete all fingerprints.

Full Fingerprint Capacity

After 20 fingerprints are registered, attempting to register more will result in 4 slow red light flashes, indicating the capacity is full, and the process will exit.

Charging Mode

Use a standard mobile phone charger and Android cable. A blue breathing light indicates charging. The blue light remains on when the battery is full. Fingerprint unlocking is available during charging.

Insufficient Power

During unlocking, if the battery is insufficient, the blue light flashes twice, followed by 4 red light flashes, indicating low power. Charge the device promptly.

Restore Factory Settings

Ensure the fingerprint lock is powered on. Insert the unlocker into the USB port and press and hold the button until a purple light appears, then release. When the light turns blue, factory settings are restored, and any fingerprint can unlock the device.