Make It Real Bracelet Craft Kits

Product Overview

This document provides instructions for creating various types of bracelets using Make It Real craft kits, including Charm Link Bracelets, Sliding Knot Bracelets, and Beaded Bracelets.

Contents and Materials

Charm Link Bracelets Kit

• Components Included: Charms, nylon cord (0.6 m / 0.53 yd each), clear elastic cord (1.5 m / 1.6 yd), assorted beads, 1 PlayTray (creation tray/bead organizer).
• Quantities: Approximately 156 assorted beads, various charm quantities (e.g., 25, 12, 10).
• Not Included: Scissors, craft glue, nail polish (optional for securing knots).

Sliding Knot & Beaded Bracelets Kit

• Components Included: Nylon cord (various lengths and colors, e.g., 40 cm light blue, 30 cm elastic), beads, charms.
• Quantities: Assorted beads and charms.
• Not Included: Scissors, craft glue, nail polish (optional for securing knots).

Legend

• Scissors: ✂️
• Center: ?
• Adhesive Tape: ?
• Craft Glue: ?
• Repeat: ?
• Let Dry: ⏳
• Knot: ?

Charm Link Bracelets Instructions

1. Step 1: Prepare Cords

   Measure and cut two 35 cm (13 ¾ in) pieces of elastic cord.

   [Diagram: Two pieces of elastic cord being measured and cut to 35 cm.]

2. Step 2: Attach Charm

   Pass one elastic cord piece through a charm loop.

   [Diagram: Elastic cord threaded through the loop of a charm.]

3. Step 3: Center Cord

   Center the elastic cord.

4. Step 4: Thread Beads

   Thread beads onto both elastic strands.

   [Diagram: Beads being threaded onto two elastic cords.]

5. Step 5: Secure to Tray

   Attach the ends of the elastic cord to the PlayTray and secure with a piece of adhesive tape to prevent beads from falling off.

   [Diagram: Elastic cord ends taped to a bead tray.]

6. Step 6: Repeat for Second Bracelet

   Repeat steps 2 to 4 with the other elastic piece and the second charm loop.

7. Step 7: Tie and Secure Knots

   Make a jeweler's knot with all four elastic ends. Secure the knot by covering it with a drop of craft glue or clear nail polish. Allow 5 minutes to dry and cut off any excess cord after the knot.

   [Diagram: Illustrates tying a jeweler's knot and securing it with glue.]

Sliding Knot Bracelets Instructions

1. Step 1: Cut Blue Cord

   Measure and cut a 40 cm (15 ¾ in) piece of light blue cord.

   [Diagram: Measuring and cutting a 40 cm piece of light blue cord.]

2. Step 2: Thread Beads and Knot

   Thread the beads onto the cord as shown. Center them in the middle. Make a tight simple knot on either side of the beads.

   [Diagram: Beads threaded onto cord, centered, with knots on each side.]

3. Step 3: Create Sliding Knot

   Make a simple knot with thread A on thread B, leaving 8 cm of excess cord. Repeat with thread B on thread A.

   [Diagram: Illustrates making knots with two threads to create a sliding mechanism.]

4. Step 4: Add Pearl Bead and Knot

   Thread a pearl bead on one end of the cord as shown and make a simple knot 4 cm (1 ½ in) after the end of the thread. Repeat on the other side.

   [Diagram: Pearl bead added, knot tied 4 cm from end.]

5. Step 5: Secure Knots

   Secure the knots by covering them with a drop of craft glue or clear nail polish. Allow 5 minutes to dry and cut off any excess cord after the knot.

   [Diagram: Securing knots with glue.]

6. Step 6: Make Second Bracelet

   Repeat steps 1 through 4 to make the other sliding knot bracelet.

Beaded Bracelets Instructions

1. Step 1: Cut Elastic Cord

   Measure and cut a 30 cm (12 in) piece of elastic cord.

   [Diagram: Measuring and cutting a 30 cm piece of elastic cord.]

2. Step 2: Attach Cord to Tray

   Attach the 30 cm (12 in) cord to the PlayTray and secure with a piece of adhesive tape.

   [Diagram: Elastic cord attached to bead tray with tape.]

3. Step 3: Thread Beads and Charm

   Thread the beads and the charm onto the cord following the sequence shown. Mix up the order to customize your bracelet!

   [Diagram: Beads and charm threaded onto elastic cord in a sequence.]

4. Step 4: Tie and Secure Knots

   Make a jeweler's knot. Secure the knot by covering it with a drop of craft glue or clear nail polish. Allow 5 minutes to dry and cut off any excess cord after the knot.

   [Diagram: Illustrates tying a jeweler's knot and securing it with glue.]

5. Step 5: Make Second Bracelet

   Repeat steps 1 through 4 to make the other beaded bracelet.

Safety Warnings and Care

WARNING!

• CHOKING HAZARD: Contains small parts. Not suitable for children under 3 years.
• Functional Sharp Points: Be aware of sharp components.
• STRANGULATION HAZARD: Contains long cords. Adult supervision is required.

Care Instructions:

• Before wearing, gently pull on bracelets to ensure knots are secure.
• Avoid submerging bracelets in water.

[Diagram: A finished bracelet. Diagram showing a person gently pulling a bracelet to test security. Diagram showing a person avoiding water.]

Manufacturer Information

Made in China

© 2022 MAKE IT REAL, LLC

USA Contact: MAKE IT REAL, 1700 Reisterstown Rd Ste 211, Pikesville MD 21208 USA, +1 410-995-8685

UK Contact: Jactin House, 24 Hood Street, Ancoats Urban Village, Manchester, M4 6WX UK, +44 (0) 161 302 4100

Website: makeitrealplay.com