LYRIDE Y1013 Clock Table Lamp
Specifications
- Model: A5236
- Material: ABS+PC
- Light Source: LED
- Input: 5V 2A
- Rated Power: 1.5W
- Dimension: 4.17 x 3.5 x 3.5 in / 106 x 89 x 89 mm
- Weight: 8.32 oz / 236g
When using for the first time, please fully charge. When using for the first time, please turn on the power switch.
Product Description
Quick Use Guide
- When using for the first time, please fully charge.
- Then, turn on the power.
- Press and hold the
button for 3 seconds to enter the clock setting state; Use the “+” and “-” buttons to set the hour. - Press the button to confirm the hour setting and enter the state of minute setting; Use the “+” and “-” buttons to set the minute;
- Press the button to confirm the minute setting and exit the clock setting state.
- Press the top button: Turn on or off the light.
- Rotate the top button: Adjust the brightness.
- Press and hold the top button: Switch color temperature.
Lyridz Remote Control Y1013
- Short press once: turn on/off the light
- Press and hold when the light is on: adjust brightness
- Press and hold when the lights are off: display clock
Note: Do not use it in a position that is pressed for a long time.
How to pair with lights?
- Step 1: Turn off the power of the light to be paired.
- Step 2: Turn on the power of the 1ght to be paired and press the remote control once within 5 seconds. The light will flash quickly, indicating successful pairing.
How to view and switch between 12H and 24H?
View
Press the “+” and “-” buttons once at the same time, and the clock display area will display the current status;
Switch
Press and hold the “+” and “_” buttons for 3 seconds at the same time, and the clock display area will show the status after switching.
Note: he time needs to be readjusted after switching.
Specs
| Model | A5236 |
| Material | ABS+PC |
| Light Source | LED |
| Input | 5V 2A |
| Rated Power | 1. 5W |
| Dimension | 4. 17*3. 5*3.5 in / 106*89*89 mm |
| Weight | 8.32 oz / 236g |
Specs of Remote Control
| Model | Y1013 | ||
| Material | ABS+Electronic Component | Battery Type | CR2032 |
| Rated Voltage | 3V | Dimension | 2.0*2.0*0.53in
51*51*13. 5mm |
| Rated Power | 0. 1W | Weight | 0. 63oz/18g |
Important Safety Information
- To ensure correct and safe installation, function of the product, please follow the below instructions and keep this booklet for future reference.
- Do not use light around water. Avoid liquids on all electrical parts.
- Clean only with a dry, soft cloth. Household cleaners or solvents can damage your light.
- Do not install your light near any heat sources, such as radiators, heat registers, stoves, or any other apparatus that produces heat.
- Do not block any ventilation openings.
- To reduce the risk of fire or electric shock,do not expose this light to rain or moisture. Keep packaging materials(e.g.plastic bags)out of childern’s reach.
- Not suitable for children under 36 months.Small parts has choking hazard. Do not stare at the operating light source.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
This LYRIDZ table lamp is fully compliant with the EU, CA, JP, U,K and USA legislation. When disposing of this equipment, please protect our environment by means of proper disposal. Your local authorities will have special return and disposal facilities available for you. CAN ICES-005(B)/NMB-005(B) Made in China Model: A5236
Linkfar Healthcare GmbHNiederrheinstraße 71, 40474 Düsseldorf Germany AOCE LIMITED Office Suite 29a 3/F 23 Wharf Street, London, England, SE
Customer Service
- 12-month limited warranty, lifetime technical support support@lyridz.com
Frequently Asked Questions
Q: Is the Clock Table Lamp compatible with all power outlets?
A: The lamp has an input of 5V 2A, so ensure your power outlet meets these specifications for safe operation.
Q: How do I adjust the brightness of the lamp?
A: Use the Lyridz Remote Control Y1013 to adjust the brightness by pressing and holding the button when the light is on.
Documents / Resources
 |
LYRIDE Y1013 Clock Table Lamp [pdf] User Manual Y1013 Clock Table Lamp, Y1013, Clock Table Lamp, Table Lamp, Lamp |