User Manual for LYRIDE models including: Y1013 Clock Table Lamp, Y1013, Clock Table Lamp, Table Lamp, Lamp
Dongguan Nuomi Innovation Technology Co., Ltd. Y1013 2A5WY-Y1013 2A5WYY1013 y1013
Clock Table Lamp User Manual Product Description Indicator Light · Flash red : Low power ·Solid red : Charging ·Solid Green: Fully charged Charging port The Top button · Press: Turn on or off the light ·Rotate: Adjust the brightness · Press and hold: Switch color temperature Luminous Area Clock Area When using for the fi rst time, please fully charge; When using for the fi rst time, please turn on the power switch. 1506000094 ON OFF Clock Setting Button ·Press: Adjust clock brightness · Press and hold 3s: Set the clock " +" Button Change parameter " - " Button Change parameter Power Switch Turn on or off the whole power Quick Use Guide ON OFF ·When using for the fi rst time, please fully charge; ·Then, turn on the power . · Press and hold the button for 3 seconds to enter the clock setting state; Use the "+ " and "- " buttons to set the hour; · Press the button to confi rm the hour setting and enter the state of minute setting; Use the "+ " and "- " buttons to set the minute; · Press the button to confi rm the minute setting and exit the clock setting state . · Press the top button: Turn on or off the light; · Rotate the top button: Adjust the brightness; · Press and hold the top button: Switch color temperature . Lyridz Remote Control Y1013 Short press once: turn on/ o ff the light Press and hold when the light is on: adjust brightness Press and hold when lights are off: display clock Note: Do not use it in a position that is pressed for a long time . How to pair with lights? Step 1 : Turn off the power of the light to be paired. Step 2: Turn on the power of the light to be paired and press the remote control once within 5 seconds . The light will flash quickly, indicating successful pairing. How to view and switch between 12H and 24H? ON OFF View: Short press the "+ " and "- " buttons once at the same time, the clock display area will display the current status; Switch : Press and hold the "+ " and "- " buttons for 3 seconds at the same time, the clock display area will show the status after switching. Note: he time needs to be readjusted after switching. Specs Model Material Light Source Input Rated Power Dimension Weight A5236 ABS+PC LED 5V 2A 1. 5W 4. 17*3. 5*3.5 in / 106*89*89 mm 8.32 oz / 236g Specs of Remote Control Model Material Rated Voltage Rated Power Y1013 ABS+Electronic Component 3V 0. 1W Battery Type Dimension Weight CR2032 2.0*2.0*0.53in 51*51*13. 5mm 0. 63oz/18g Important Safety Information To ensure correct and safe installation,function of the product,please follow below instructions and keep this booklet for future reference. Do not use light around water.Avoid liquids on all electrical parts. Clean only with a dry,soft cloth.Household cleaners or solvents can damage your light. Do not installyour light near any heat sources,such as radiators,heat registers,stoves,or any other apparatus that produces heat. Do not block any ventilation openings. To reduce the risk offire or electric shock,do not expose this light to rain or moisture. Keep packaging materials(e.g.plastic bags)out of childern's reach. Not suitable for children under 36 months.Small parts has choking hazard. Do not stare at the operating light source. FCC Warning This device complies with Part 15 ofthe FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one ofthe following measures: ·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This LYRIDZ table lamp is fully compliant with the EU, CA JP UK and USA legislation. When disposing this equipment,please protect our environment by means of proper disposal.Your local authorities will have special return and disposal facilities available for you. CAN ICES-005(B)/NMB-005(B) Made in China Model: A5236 Linkfar Healthcare GmbHNiederrheinstraße 71, EC REP 40474 Düsseldorf Germany AOCE LIMITED UK REP Office Suite 29a 3/F 23 Wharf Street, London, England, SE Customer Service 12-month limited warranty lifetime technical support support@lyridz. comMicrosoft Word 2013 Microsoft Word 2013