Lumens - logoLC100 Installation Guide
LC100 Capture Vision System

Instruction Manual

Lumens LC100 CaptureVision System

Introduction of Product Functions

1.1 Front View

Lumens LC100 CaptureVision System - 1 Front View

1.2 Back ViewLumens LC100 CaptureVision System - Back View

1.3 Function Descriptions

No. Item Function Descriptions No. Item Function Descriptions
1. LCM Display Menu and Information 16 DC IN 12V DC 12 V power connector
2. Knob LCM knob 17 Input ■ HDMI Input 1
■ 3G-SDI Input 1
■ HDMI Passthrough
3 Record Start/Stop recording
4 Stream On/Off image streaming 18 Input2 ■ HDMI Input 2
■ 3G-SDI Input2
5 Scene Switch templates 19 Output ■ PGM: Main screen output, display the recording or streaming screen and layout
■ Multiview: Operation interface output; display the settings menu and image management
6 Power On/Off the device power
7 Single Channel Display a single channel screen
8 PIP Switch to PIP (picture in picture)
9 PBP Switch to PBP (picture by picture) 20 USB3.0 port Supports the following
devices:
■ USB video/audio devices
■ External storage disk
• Keyboard/mouse
• LC-RCO1 (optional) controller
10 SWAP Switch signal channels
11 USB3.0 port for external storage disk
12 USB3.0 port for external storage disk
13 USB2.0 port Can connect to keyboard/mouse device operation menu 21 Ethernet Connect to LAN
14 Factory Reset Reset all configurations to factory default settings 22 RS-232/ RS-485 port Connect to AV control equipment
15 Restart Reboot the machine 23 XLR audio in Connect to a microphone or audio mixer
24 Line In/ Out Audio In/Out

Product connection diagram

Lumens LC100 CaptureVision System - diagram

Precautions Prior to Use

3.1 Please confirm the purchased version equipped with hard drive or not. If not, please purchase one for installation.
3.2 LC100 supports 2.5″/3.5″ SATA hard drives.
3.3 If no hard drive is installed, use a USB disk for external storage.

Hard drive installation steps

4.1 Remove the screws (5 pcs) on the top cover.

Lumens LC100 CaptureVision System - steps

4.2 Loosen the following screws.Lumens LC100 CaptureVision System - Loosen

4.3 Attach your hard drive to the connection cable.
* Please make sure the port and the L-shaped slot of the cable are aligned before insertion. Do not force the connection to avoid damage to the port.Lumens LC100 CaptureVision System - connection cable

4.4 Fasten the hard disk to the metal plate with the provided screws (4 pcs).
A. 2.5″ SATA Hard Drive holes
B. 3.5″ SATA Hard Drive holes
* Do not over-tighten the screws to avoid damage to the hard drive. Only use the screws provided.Lumens LC100 CaptureVision System - Drive holes

4.5 Lock the hard drive mounting plate in place and insert the connection cable.Lumens LC100 CaptureVision System - Drive holes 1

4.6 Close the top cover to complete the installation.
4.7 Hard drive setting
After installation, you need to log in to the web page and click Information to format the drive.
Storage Setting > Hard Disk
*Formatting the drive will erase all existing data on the disk Lumens LC100 CaptureVision System - Drive holes2

Real-time operation menu

Connect the HDMI1 Multi View output to a monitor to display the real-time operation menuLumens LC100 CaptureVision System - monitor

No. Item Function Descriptions
1 Lumens LC100 CaptureVision System - ItemConfiguration Configure the network settings and recording/streaming quality
2 Lumens LC100 CaptureVision System - Item1Director Creative control of video and audio inputs, audio feeds. Control recording and streaming and network video cameras
3 Lumens LC100 CaptureVision System - Item2File Management Transfer, upload, download, delete, and play back video files
4 Lumens LC100 CaptureVision System - Item3About Display the current LC100 firmware version
5 Device IP Displays the device’s network IP address.

Web Interface

6.1 Confirm the IP address of the device
Connect the LC100 to a router. Note the IP address of the device (visible in the lower right corner of the HDMI Multiview output screen) .
6.2 Input the devices IP address into the web browser, e.g. 192.168.100.100.Lumens LC100 CaptureVision System - Item4

http://192.168.100.100

6.3 Please enter your account/password to log in.

Lumens LC100 CaptureVision System - passwordAccount : admin
Password : admin

Web Interface
Thru the web interface users can access the File Manager, the Multi View interface and system settings.Lumens LC100 CaptureVision System - Web Interface

Director Tab

Follow these steps to access the Director Tab

  • On the Multi View interface, select Director Lumens LC100 CaptureVision System - Item1
  • Log in to the web page by entering the online Director Casting Account /Password (default setting: director/director)

Lumens LC100 CaptureVision System - Web Interface1

Lumens - logo

Copyright © Lumens Digital Optics Inc.
All rights reserved.

Documents / Resources

Lumens LC100 CaptureVision System [pdf] Instruction Manual
5100438-51, LC100, LC100 CaptureVision System, CaptureVision System

References

Leave a comment

Your email address will not be published. Required fields are marked *