Blank password
- Username
- admin
- Password / access
- Leave blank
Access: Web
D-704P Rev. REV B, DI-524, DI-524 Rev. ALL and other listed models
Source (opens in a new tab)ROUTER & MODEM REFERENCE
D-Link router & modem login
Login addresses, default credentials, and setup instructions for D-Link equipment.
Open router login http://192.168.0.1 (opens in a new tab)Open router login http://dlinkrouter.local (opens in a new tab)Open router login http://192.168.1.1 (opens in a new tab)
Connect to the router’s Wi-Fi or Ethernet first. These links open a new tab on your device; the address may differ if the network was reconfigured.
QUICK START
Most likely login options
Start with the option that matches your model. Defaults apply to the factory state; use the password you chose if the device has already been set up.
Options are ordered by manufacturer documentation and coverage among the listed models. Hardware, firmware, and ISP versions can differ.
MODEL DETAILS
Login addresses & credentials
Passwords are case-sensitive. “Leave blank” means an empty field; “Not specified” means the source does not provide that detail. Entries without a model are brand-level references.
| Model / device | Login address | Username | Password / access | Notes & source |
|---|---|---|---|---|
| D-Link–Router · Not specified | – | root | admin | Model not specified by this list. |
| D-Link–Router · Not specified | – | Admin | Leave blank | Model not specified by this list. |
| D-Link–Router · Not specified | – | admin | gvt12345 | Model not specified by this list. |
| D-Link–Router · Not specified | – | No username required | private | Model not specified by this list. |
| D-Link–Router · Not specified | – | none | private | Model not specified by this list. |
| D-Link–Router · Not specified | – | admin | year2000 | Model not specified by this list. |
| D-Link–Router · Not specified | – | No username required | admin | Model not specified by this list. |
| D-Link–Router · Not specified | – | D-Link | D-Link | Model not specified by this list. |
| D-Link–Router · Not specified | – | Alphanetworks | wrgg15_di524 | Model not specified by this list. |
| D-Link–Router · Not specified | – | user | Leave blank | Model not specified by this list. by rootkid |
| D-Link–Router · Not specified | – | dont need one | admin | Model not specified by this list. |
| D-Link–Router · Not specified | – | admin | none | Model not specified by this list. |
| D-Link–Router · Not specified | – | admin | password | Model not specified by this list. hardcoded for Verizon FiOS |
| D-Link–Router · Not specified | – | admin | admin | Model not specified by this list. |
| D-Link–Router · Not specified | – | No username required | public | Model not specified by this list. |
| D-Link–Router · Not specified | – | user | none | Model not specified by this list. |
| D-Link–Router · Not specified | – | none | none | Model not specified by this list. |
| D-Link–Router · Not specified | – | admin | public | Model not specified by this list. |
| D-Link–Router · Not specified | – | Not specified | admin | Model not specified by this list. |
| D-Link–Router · Not specified | – | admin | Leave blank | Model not specified by this list. |
| D-Link504G ADSL ROUTERModem / gateway · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-Link604Router · MULTI | – | Not specified | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkADSLModem / gateway · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkADSL Modem/Router (DSL series)Modem / gateway · Web | http://192.168.1.1 (opens in a new tab) | admin | admin | D-Link's official support states the default for its ADSL modem/router (DSL series) is admin / admin at 192.168.1.1 — many older Airtel/BSNL/MTNL DSL units are these. D-Link also notes that units purchased after 2017 are secure by default with a unique password printed on the bottom of the unit, so check the label on newer hardware. Recovery & reset instructionsConnect to the modem/router by LAN or Wi-Fi, open http://192.168.1.1 in a browser, and sign in with username admin and password admin (D-Link's documented default for its DSL series). If the login is rejected, the password was likely changed — keep the username admin and enter your own password. To factory reset, hold the recessed RESET button for about 10 seconds until the unit reboots, then log back in with admin / admin and reconfigure. |
| D-LinkD-704PRouter · MULTI | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkD-704P Rev. REV BRouter · MULTI | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDGL4300 Rev. D-LINK'S DGL-4300 GAME SERIES ROUTERRouter · HTTP | – | Admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-514Router · MULTI | – | user | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-524Router · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-524 Rev. ALLRouter · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-524 Rev. ALLRouter · HTTP | – | user | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-604 Rev. 1.62B+Router · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-604 Rev. 2.02Router · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-604 Rev. REV A REV B REV C REV ERouter · MULTI | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-614+Router · HTTP | – | user | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-614+Router · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-614+ Rev. ANYRouter · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-624 Rev. ALLRouter · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-624 Rev. ALLRouter · HTTP | – | User | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-624+ Rev. A3Router · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-704Router · MULTI | – | Not specified | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-704 Rev. REV ARouter · MULTI | – | No username required | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-707P ROUTERRouter · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI-804 Rev. V2.03Router · MULTI | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDI624 Rev. C3Router · HTTP | – | admin | password | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDIR-615Router · Web | http://192.168.0.1 (opens in a new tab) | admin | Leave blank | D-Link's documented default is username admin with a blank password — there is no admin/admin. D-Link's official login FAQ confirms admin with password blank by default for this era of routers. Recovery & reset instructionsOpen a browser to http://192.168.0.1, select admin as the User Name and leave the Password blank, then click Log In. To factory reset, with the router on, press and hold the recessed Reset button on the bottom for about 10 seconds until it reboots; the password returns to blank. |
| D-LinkDIR-655Router · Web | http://192.168.0.1 (opens in a new tab) | admin | Leave blank | The official D-Link DIR-655 manual and Quick Install Guide state the default username is admin and the default password is blank (leave the field empty). No admin/admin exists for this model. Recovery & reset instructionsOpen a browser to http://192.168.0.1, choose Admin from the user drop-down, leave the password field blank, and click Log In. To reset, press and hold the Reset button on the back for about 10 seconds until the router reboots; the password reverts to blank. |
| D-LinkDIR-825Router · Web | http://192.168.0.1 (opens in a new tab) | admin | Leave blank | The official D-Link DIR-825 user manual documents username admin with the password left blank by default. Owners are expected to set a password on first configuration. Recovery & reset instructionsOpen a browser to http://192.168.0.1, enter admin as the username, leave the password blank, and log in. Factory reset: hold the Reset button on the underside for about 10 seconds with the unit powered on until it restarts; the password returns to blank. |
| D-LinkDIR-882Router · Web | http://192.168.0.1 (opens in a new tab) | admin | Password created during setup | Ships with NO admin password — the setup wizard forces you to create one. Classic login username is admin. Recovery & reset instructionsWith the router on, insert a paperclip into the recessed Reset hole on the back and hold ~10 seconds, then release to restore factory defaults. |
| D-LinkDIR-X1560 (EXO AX1500)Router · Web | http://192.168.0.1 (opens in a new tab) | No username required | Password created during setup | No default password — the login screen has only an Admin Password field (no username). Leave blank if the setup wizard hasn't run; otherwise use the password you created. Recovery & reset instructionsInsert a paperclip into the recessed Reset hole on the back and hold longer than 10 seconds, then release to restore defaults. |
| D-LinkDIR-X1870 (EXO AX1800)Router · Web | http://dlinkrouter.local (opens in a new tab)http://192.168.0.1 (opens in a new tab) | No username required | password | Wi-Fi 6 (802.11ax) AX1800 dual-band mesh-capable router (EXO AX line) — a lower tier than the AX5400 DIR-X5460. Web or D-Link Wi-Fi app setup. D-Link's Quick Install Guide states a static default: "You will be asked for your Device/Admin Password. By default this password is 'password'." Recovery & reset instructionsUse a paperclip to press and hold the recessed Reset button for longer than 10 seconds to restore default settings, then reconnect to the Wi-Fi on the Quick Installation Card and set up again. |
| D-LinkDIR-X3260 (EXO AX3200)Router · Web | http://dlinkrouter.local (opens in a new tab)http://192.168.0.1 (opens in a new tab) | No username required | password | AX3200 dual-band mesh-capable Wi-Fi 6 EXO-series router with Gigabit WAN — a lower-tier sibling of the DIR-X4860. The first web login prompts only for a Device/Admin Password with the factory value "password" (no username). D-Link: "You will be asked for your Device/Admin Password. By default this password is 'password'." Recovery & reset instructionsPower the router on, then use a paperclip to hold the recessed rear Reset button ~10 seconds and release to restore factory defaults; the Device/Admin password reverts to "password". |
| D-LinkDIR-X4860 (EXO AX4800)Router · Web | http://dlinkrouter.local (opens in a new tab)http://192.168.0.1 (opens in a new tab) | No username required | password | AX4800 dual-band mesh-capable Wi-Fi 6 (802.11ax) EXO-series router with Gigabit WAN (Ethernet). Genuine static default: the first web login asks only for a Device/Admin Password whose factory value is the word "password" (no username field). D-Link: "You will be asked for your Device/Admin Password. By default this password is 'password'." Recovery & reset instructionsWith the router powered on, use a paperclip to hold the recessed rear Reset button ~10 seconds, then release to restore factory defaults (the Device/Admin password returns to "password"). |
| D-LinkDIR-X5460 (EXO AX5400)Router · Web | http://dlinkrouter.local (opens in a new tab)http://192.168.0.1 (opens in a new tab) | No username required | password | Wi-Fi 6 (802.11ax) AX5400 dual-band mesh-capable router with a dual-core CPU and detachable antennas. D-Link's Quick Install Guide states a genuine static default: "You will be asked for your Device/Admin Password. By default this password is 'password'." Some revisions' user manuals instead cite a label-printed password, so confidence is medium. Recovery & reset instructionsUse a paperclip to press and hold the recessed Reset button on the back for longer than 10 seconds to restore the router to default settings. |
| D-LinkDSL-300G+ Rev. TEORouter · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL-300G+ Rev. TEORouter · TELNET | – | No username required | private | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL-302GRouter · MULTI | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL-500Router · MULTI | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL-504TRouter · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL-G604TRouter · MULTI | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL-G664T Rev. A1Router · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDSL500GRouter · MULTI | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL 1000Router · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL 2100APRouter · MULTI | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL 900APRouter · MULTI | – | No username required | public | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL-2000AP+ Rev. 1.13Router · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL-614+ Rev. 2.03Router · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL-614+ Rev. REV A REV BRouter · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL-900+Router · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkDWL-900AP+ Rev. REV A REV B REV CRouter · HTTP | – | admin | Leave blank | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkEAGLE PRO AI E15Mesh system · Web | – | No username required | Password on the device label | AX1500 Wi-Fi range extender (WPS or EAGLE PRO AI app setup, reachable at http://WXYZ.devicesetup.net where WXYZ = the last 4 characters of the device's MAC address). Official D-Link Quick Installation Guide: "The Wi-Fi Name/SSID, Wi-Fi Password, and device password are printed on the Quick Installation Guide and on the device label." Also: "By default, your device will share the same Wi-Fi name and password as your router" when paired via WPS. Recovery & reset instructionsWith the Range Extender powered on, use a paperclip to hold the reset button down until the LED turns solid red, then release — this restores factory defaults. |
| D-LinkFIREWALL Rev. DFL-200Router · HTTP | – | admin | admin | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkM15 (AQUILA PRO AI AX1500 Wi-Fi 6 AI Mesh Router)Mesh system · Web | – | No username required | Password on the device label | AX1500 dual-band (2x2) Wi-Fi 6 AI Mesh Router — entry tier below the seeded D-Link M30 (AX3000) and M60 (AX6000) AQUILA PRO AI mesh siblings, set up via the D-Link Ai app + Quick Installation Card QR code. Official QIG FAQ: "Verify that http://WXYZ.devicesetup.net/ has been correctly entered into the browser (WXYZ represents the last 4 characters of the MAC address). The Wi-Fi Name(SSID), Wi-Fi Password, and device password are printed on the Quick Installation Card and on the device label." Device hostname format: WXYZ.devicesetup.net. Recovery & reset instructionsLocate the reset button. With the router powered on, use a paper clip to hold the button down until the LED turns solid red. Release the button and the router will go through its reboot process. |
| D-LinkM30 (AQUILA PRO AI AX3000)Mesh system · Web | – | Admin | Password on the device label | Entry AQUILA PRO AI mesh: AX3000 dual-band Wi-Fi 6 (802.11ax, 574 + 2402 Mbps), sold as 2- and 3-node kits for whole-home coverage. Login username is Admin; there is no static default — each node ships with its own random Device Password on the bundled Quick Installation Card. Browser config lives at the MAC-derived devicesetup.net host. D-Link M30 QIG: "http://xxxx.devicesetup.net/ (XXXX represents the last 4 characters of the MAC address) Device Password: XXXXXX." Recovery & reset instructionsWith the router powered on, press the recessed Reset button with a paperclip for 1 second and then release it to restore factory default settings, then re-run setup in the D-Link AI app. |
| D-LinkM60 (AQUILA PRO AI AX6000)Mesh system · Web | – | Admin | Password on the device label | Flagship AQUILA PRO AI router: AX6000 dual-band Wi-Fi 6 (802.11ax, 1147 + 4804 Mbps) with a multi-gig backhaul, a step up from the AX3000 M30. The web UI account name is Admin, and instead of admin/admin the unit boots with a factory-random Device Password unique to that serial, shown on its device label and setup card. Managed through the D-Link AI app or the per-device devicesetup.net page. D-Link M60 QIG: "http://xxxx.devicesetup.net/ (XXXX represents the last 4 characters of the MAC address) Device Password: XXXXXX." Recovery & reset instructionsWith the router powered on, press the recessed Reset button with a paperclip for 1 second and then release it to restore factory default settings, then re-run setup in the D-Link AI app. |
| D-LinkVTA (VONAGE)Router · HTTP | – | user | user | Defaults may depend on the listed model, revision, firmware or ISP. |
| D-LinkVWR (VONAGE) Rev. WIRELESS BROADBAND ROUTERRouter · HTTP | – | user | user | Defaults may depend on the listed model, revision, firmware or ISP. |
No records match these filters. Try another model or clear the filters.
Related login addresses
GET CONNECTED
How to reach your router
- Connect your computer or phone to the router’s Wi-Fi or an Ethernet port.
- Open a documented login address. If it does not load, look for the Router or Default gateway address in your device’s network settings.
- Match your model and hardware revision to the table. Use the device label or your setup password when the model has no shared default.
Admin password or Wi-Fi password?
The admin password opens the router’s settings. The Wi-Fi password connects a device to the wireless network. They may be different, and an ISP or cloud account can be separate again.
If the password does not work
Check capitalization and the device label, then use the manufacturer’s password-recovery instructions. A factory reset erases settings and may require ISP setup details; follow the instructions for your exact model.
Find your model’s manual →Sources & data
Router default-credential data from ssid.ai (Drumworks Ventures FZ), licensed CC BY 4.0. Adapted, organized and supplemented by Manuals+. The data is provided as is; manufacturers and ISPs can change defaults.
Additional factual entries: Austin Songer’s credential list and Clint Milner’s credential list. Each table entry links to its supporting source. Updated 2026-10-16.