LINKBAR Single Touch Milk Module Instruction Manual

LINKBAR-logo

LINKBAR Single Touch Milk Module

LINKBAR-Single-Touch-Milk-Module-product

THANK YOU FOR YOUR PURCHASE

This product is designed for general use and may not be suitable for individuals with specific needs or disabilities. For children’s safety, adult supervision is required at all times.

Features

LINKBAR-Single-Touch-Milk-Module-fig (1)

Safety Instruction

  1. Remove all packaging materials before use.
  2. The drain hose must be æcurely ccnnected toa drain outlet. The machine will dicharge a small amcunt of hot water during operation. Avoid directing the drain outlet towards areas where people may be present to prevent æalding.
  3. Ensure that the gnwer ccrd, water supply tube, and drain hose are connected correctly and swurely.
  4. Do not touch the milk outletdirectly with ycur hands to avoid bums I-Jse a clean cloth to wipe it
  5. If the machine malfunctions, pleaæ contact after-salß service fcr repair immediately IJnauthorized repairs may damage the pipes and Cal-Æ the milk to spoil during the production process

Specification

Specification Details
Dimension (L×W×H) Tap & Host: 500020 × 147 mm
Types 4 + Custom Settings
Voltage 220V 16A
Power 3400W
Weight
Tap: 1.4 kg (Net Weight)


Host: 18 kg (Net Weight)
Output 120 cups/h (200 ml/cup)

THINGS TO KNOW

BEFORE INSTALLATION

  • Notice: Wrong plumbing can cause malfunction on the machine.
  • The equipment must installed with bæklow protecticn to comply with all applicable federal, state, and local codes.

COMPONENTSLINKBAR-Single-Touch-Milk-Module-fig (2)

Rear View of the Main Unit LINKBAR-Single-Touch-Milk-Module-fig (3)

MILK BUCKET INSTALLATION DIAGRAM LINKBAR-Single-Touch-Milk-Module-fig (4)

  1. Faucet
  2. Pitcher Rack& Water Tray
  3. Countertop Hole (See Upper Right)
  4. Fount Discharge (With Silicone Hose)
  5. Fount Inlet (With Transparent Tube)
  6. Faucet Data Cable
  7. Main Unit
  8. Machine Power Cord (220V 16A Three-prong Socket)
  9. Center Cutout In The Shelf (Shelf Can Hold Up To 60kg)LINKBAR-Single-Touch-Milk-Module-fig (52)
  10. Cleaning Tube (Black Silicone Hose)
  11. Milk Jug
  12. Milk Inlet (With Silicone Hose)
  13. Milk Bucket
  14. Water Inlet (With Transparent Tube)
  15. Pressure Reducing Valve (Installation Required For Water Pressure Above 4bar)
  16. Water Purifier
  17. Y-Valve
  18. Drainage (With Tube)
  19. Drain For Filter Tray

Installation Instruction

  1. STEP1: Open the milk bucket.LINKBAR-Single-Touch-Milk-Module-fig (5)
  2. STEP2 Pour the milk into the milk bucket. LINKBAR-Single-Touch-Milk-Module-fig (6)
  3. STEP3 Insert the milk inlet tutethe milk bucket LINKBAR-Single-Touch-Milk-Module-fig (7)

Right-side View of the Main UnitLINKBAR-Single-Touch-Milk-Module-fig (8)

  1. Faucet
  2. Fount Dicharge ONith Silicone Hcse)
  3. Fount Inlet (With Transparent Tube)
  4. Faucet Data Cable
  5. Drainage (With Transparent
  6. Cleaning Tube (Black Silicone Hose)
  7. Milk Jug
  8. Milk Inlet (With Silicone Hoæ)
  9. Milk Bucket
  10. Water Inlet (With Transparent Tube)
  11. Pressure Valve (Installation For Water Pressure Above 4bar)
  12. Water Purifier
  13. Y-Valve
  14. Machine Power Cccd (220v 16a Three-prong Sccket)

REFRIGERATOR INSTALLATION DIAGRAM

Unit: mm LINKBAR-Single-Touch-Milk-Module-fig (9)

  1. Faucet
  2. Pitcher Rack& Water Tray
  3. Countertop Hole (See Upper Right)
  4. Faucet Data Cable
  5. Main Unit
  6. Fount Discharge (With Silicone Hose)
  7. Fount Inlet (With Transparent Tube)
  8. Drain Tube For Filter Tray
  9. Drainage (With Transparent Tube)
  10. Water Inlet (With Transparent Tube)
  11. Milk Inlet (With Silinre Hose)
  12. Refrigerator
  13. Machine Power Cord (220V 16A Three-prong Socket)
  14. Cleaning (Black Silicone Hose)
  15. Milk Jug
  16. Refrigerator Power Cord (220v, 10a 5 Hole Scket)
  17. Pressure Reducing Valve (Installation Required For Water Pressure Above 4 bar)
  18. Water Purifier
  19. Y-valve

Installation Steps

  1. STEP 1: Prepare the milk and the milk container.LINKBAR-Single-Touch-Milk-Module-fig (10)
  2. STEP2: Pour the milk into the milk container. LINKBAR-Single-Touch-Milk-Module-fig (11)
  3. STEP 3: Put the milk container into the small fridge. Insert the milk inlet tube into the milk through the hole LINKBAR-Single-Touch-Milk-Module-fig (12)
  4. STEP4: Close the fridge door. LINKBAR-Single-Touch-Milk-Module-fig (13)

Right-side View of the Main Unit LINKBAR-Single-Touch-Milk-Module-fig (14)

  1. Faucet
  2. Fount Discharge (With Silicone Hose)
  3. Fount Inlet (With Transparent Tube)
  4. Faucet Data Cable
  5. Drainage (With Tube)
  6. Cleaning Tube (Black Silicone Hose)
  7. Milk Jug
  8. Milk Inlet (With Silicone Hose)
  9. Refrigerator
  10. Water Inlet (With Transparent Tube)
  11. Pressure Valve (Installation For Water Prssure Above 4bar)
  12. Water Purifier
  13. Y-Valve
  14. Main Unit Power Cord (220v 16a Three-prong Socket)
  15. Refrigerator Power Cord (220v, 10a 5 Hole Socket)

PARAMETER ADJUSTMENT

SCREEN DISPLAY CONTENT

  1. Power on: Before you start, make sure all the cords and tL&s are plugged in tight Find the butcn on the lef side cf the machine and press it You’ll see our lcgo pop up. LINKBAR-Single-Touch-Milk-Module-fig (15)
  2. Self-cleaning: Once it’s turned on, the machine will start cleaning itself for about 30 æoonds. LINKBAR-Single-Touch-Milk-Module-fig (16)
  3. Heating: After cbanirg S completed, tte machine will automatically Feat up to the set initial temperature. LINKBAR-Single-Touch-Milk-Module-fig (17)
  4. Main Screen: The machire atdomaically heats up to the cperating emperature and eners the main interface Now ifs ready for rurra I operator, (The temperatue shown on tie ton is the iccnS Emperature, Vith a boot up to 20 oc above the et iniial LINKBAR-Single-Touch-Milk-Module-fig (18)
  5. To maximize production efficiency, the faucet ion’s settings are preset and cannot changed manually. To adjust parameters pleaæ navigate to the main unit interfæe below. LINKBAR-Single-Touch-Milk-Module-fig (19)

FUNCTIONS

MAIN INTERFACE -SETTINGS INTERFACE

Tap ‘Settings’ to enter the settings interfaæ. LINKBAR-Single-Touch-Milk-Module-fig (20)

  • Cleaning: Use for the daily cleaning and blockage cleaning. (Settings – Cleaning)
  • Language: Two language options: Chinese, English. (Settings – Language)
  • Temperature (Initial Temp)
    • Use for the temperature setting: Minimum 40 °C, maximum 60 °C. (Settings – Temperature)
    • According “Settings – Temperature”, the temperature can be adjusted up by a maximum of 20°C from the set initial temperature. (Long-press LINKBAR-Single-Touch-Milk-Module-fig (21)the icons to adjust the temperature)
  • Factory Reset: Restore all settings to factory defaults. (Settings – Factory Reset)
  • ADV Settings: Edit the parameters of the tube pre-filling, pump speed, brightness, standby cleaning, etc. (Settings – ADV settings)
  • Software: Supports future system upgrades. (Settings – Software)
  • Time: Use to configure the time displayed on the main screen. (Settings – Time)
  • Usage Record: An engineer’s tool for monitoring machine performance, including testing electronic valves. (Settings – Usage Record)

Operation Procedure

All operations can be adjusted by tapping, long-pressing, or swiping on the display screen.
One-Touch Output
  • Simply tap the correspondingLINKBAR-Single-Touch-Milk-Module-fig (21)icons to initiate the output process according to the preset settings.
  • The process can be manually halted by tapping the icon again.LINKBAR-Single-Touch-Milk-Module-fig (22)
Adjusting Milk Foam Parameters
  1. Long press the corresponding menuLINKBAR-Single-Touch-Milk-Module-fig (21)icon to enter the milk froth parameter adjustment interface, adjust the required parameter values, and then click LINKBAR-Single-Touch-Milk-Module-fig (25)to enter the parameter confirmation interface.
    1. Milk Volume: Based on the cup size, the corresponding milk froth output time is set to approximately 15g/second.

      LINKBAR-Single-Touch-Milk-Module-fig (23)

    2. Air Ratio: Indicates the thickness of the milk froth.
    3. Temperature: The temperature of the cold milk froth is the original temperature of the milk. For other temperatures, you can refer to “Settings – Heating” and add an additional 20°C (for example, if the initial temperature is set at 40°C, it allows for temperature adjustments between 40°C and 60°C).
      • The longer the milk dispensing time (up arrow symbol), the greater the milk volume.
      • The shorter the milk dispensing time (down arrow symbol), the smaller the milk volume.
      • The higher the milk froth ratio (up arrow symbol), the thicker the milk froth.
      • The lower the milk froth ratio (down arrow symbol), the thinner the milk froth.
  2. Tap to deselect and retum to the previous screen. Tap to confirm the parameter changes, which will overwrite the original values and create a new settingLINKBAR-Single-Touch-Milk-Module-fig (24)

REMOVE MENU ICONS

  1. Long-press theLINKBAR-Single-Touch-Milk-Module-fig (21)icons to enter the parameter setting interface, then click on “DELETE” to enter the confirmation interface.LINKBAR-Single-Touch-Milk-Module-fig (27)
  2. TapLINKBAR-Single-Touch-Milk-Module-fig (25)to deselect and return to the previous screen, or tap LINKBAR-Single-Touch-Milk-Module-fig (26)to confirm the deletion of the menu icon.

LINKBAR-Single-Touch-Milk-Module-fig (28)

DEBUGGING THE WATER OUTPUT AND MILK PRODUCTION

  1. Main Interface: Long-press the corresponding LINKBAR-Single-Touch-Milk-Module-fig (21) menu icon to enter the milk froth settings interface. LINKBAR-Single-Touch-Milk-Module-fig (29)
  2. 2. Debugging The Milk Froth Production Interface After adjusting the desired milk froth parameters, tap “ADVANCED” in the bottom right corner to enter the water output adjustment interface. LINKBAR-Single-Touch-Milk-Module-fig (30)
  3. Passcode Input Interface: Enter the passcode. This is the time displayed on the machine. For example, if the time is 1347, please enter 1347 in the passcode field and click LINKBAR-Single-Touch-Milk-Module-fig (26)to confirm.
  4. Water Output Adjustment Interface
    1. FRONT-END WATER: If clear water is dSpenæd at the beginning of the process, the pre-flll time in small increments. Press LINKBAR-Single-Touch-Milk-Module-fig (25) to confirm and acces the confirmation screen.
    2. BACK-END WATER: If water is præent at the end of the prcæs, decreaæ the post-empty tirne in small increments Press LINKBAR-Single-Touch-Milk-Module-fig (25) to confirm and the cmfirmation scræn. Observe until no water is visibleLINKBAR-Single-Touch-Milk-Module-fig (51)
  5. Confirm Parameters Interface To cancel your selætion and retum to the previous screen, tap e. To confirm the parameters, tap LINKBAR-Single-Touch-Milk-Module-fig (26)

ADD NEW PARAMETER BUTTON

  1. Add New Parameter Button, tap 6, and enter the milk frothing settings.
  2. Milk Froth Parameter Adjustment Interface:  Slide or tap the progress bar to select the desired parameter value. Then, choose OO hot/cold milk fräh below. Tap to to enter the menu icon interfaæLINKBAR-Single-Touch-Milk-Module-fig (31)
  3. Parameter Icon Selection Interface: Tap to deselect and return to the previous Tap to enter the menu name interface.
  4. Parameter Name Selection Interface: Tap e to deselæt and retum to the previous screen. Tap 9 to confirm changes. LINKBAR-Single-Touch-Milk-Module-fig (32)
  5. Confirm Change Interface: Tap to cancel and return to the previous screen. Tap to confirm and add to the home screen
  6. Home Screen Addition Complete: The main unit’s home screen has been successfully updated. 16 new parameter icons can be added The tabletop faucet can only control the first 4 parameter icons on the main unit’s home screen, The remaining parameter icons can only be controlled on the main unit’s screen. All parameter icons on the main unit’s home screen can be long-pressed to modify the milk froth ratio, milk volume, temperature, and hot/cold type.LINKBAR-Single-Touch-Milk-Module-fig (33)

TEMPERATURE (Initial Temp)

 

  1. Main Screen – Settings: Tap “Settings” to enter the function selection interface.LINKBAR-Single-Touch-Milk-Module-fig (34)
  2. Settings – Temperature: Tap “Temperature” to enter the temperature adjustment interface.
  3. Temperature Adjustment Interface: Tap or slide the progress bar to the desired temperature, then tap to enter the confirmation interface. The minimum temperature is 40°C, and the maximum is 60°C.LINKBAR-Single-Touch-Milk-Module-fig (35)
  4. Confirm Parameter Interface: Tap LINKBAR-Single-Touch-Milk-Module-fig (25)to cancel and return to the previous screen. Tap LINKBAR-Single-Touch-Milk-Module-fig (26)to confirm the parameter modification and overwrite the original value, setting a new default (this can be modified flexibly).

CLEANING

  1. Main Screen – Settings – Cleaning: Tap “Cleaning” to enter the cleaning parameter selection interface.
  2. Cleaning Parameter Selection Interface: Tap the icon to enter the password input interface.
  3. Passcode Input Interface: Enter the passcode displayed on the machine (for example, if the time displayed is 1347, input 1347 in the passcode field), then tap to confirm.

Cleaning Settings Interface: Tap “Cleaning Parameters” to enter the cleaning parameter adjustment interface.

LINKBAR-Single-Touch-Milk-Module-fig (37)Cleaning Parameter Adjustment Interface: Cleaning parameters are commonly adjusted and typically set to factory defaults. Parameter definitions include:LINKBAR-Single-Touch-Milk-Module-fig (38)

      1. Milk Tube Pre-Filling: The time that pushing milk from the milk tube to the milk container takes during the cleaning process.
      2. Cleaning Speed: Flow rate of the diluted cleaning solution during the cleaning process.
      3. Cleaning Water Volume: The amount of hot water ($300-400\text{ ml}$) used to dilute the cleaning tablet.
      4. Tablet Dissolve Time: Dissolving time for the cleaning tablet.
      5. Cleaning Time: The time for each intake of diluted cleaning solution.
      6. Drainage Time: Time to drain the liquid from the internal pipeline before cleaning.
      7. Clean Cycles: Total number of cleaning cycles.
      8. Rinse Cycles: Total number of rinsing cycles.
  2. Parameters Confirmation Interface: To cancel your selection and return to the previous screen, tap LINKBAR-Single-Touch-Milk-Module-fig (25). To confirm the parameters, tap LINKBAR-Single-Touch-Milk-Module-fig (26).LINKBAR-Single-Touch-Milk-Module-fig (39)

Cleaning Water Volume Calbration: Tap “Cleaning Water Volume & Calibration” to enter the parameter adjustment interface.

LINKBAR-Single-Touch-Milk-Module-fig (40)

  1. Cleaning Water Time Calibration: Put The Eaning tube in a clean cup. Tap the button to start draining hot water and rinsing.LINKBAR-Single-Touch-Milk-Module-fig (41)
  2. Cleaning Water Time Calibration: Onæ the hot water volume falls within the specified range,tap LINKBAR-Single-Touch-Milk-Module-fig (54)to pause the discharge. Weigh the discharged water using a precision electronic scale. If the weight is correct, tapLINKBAR-Single-Touch-Milk-Module-fig (25) to continue. If the volume is insufficient, empty the cup and tap LINKBAR-Single-Touch-Milk-Module-fig (54)to restart.LINKBAR-Single-Touch-Milk-Module-fig (42)
  3. Cleaning Water Time for Cleaning: Tap LINKBAR-Single-Touch-Milk-Module-fig (53)to set the drain time to 20 seconds.

LINKBAR-Single-Touch-Milk-Module-fig (43)

ADV SETTINGS

  1. Main Interface – Settings: Tap “Settings” to enter the function selection interface.LINKBAR-Single-Touch-Milk-Module-fig (44)
  2. Settings – ADV Settings: Tap “ADV settings” to enter the password screen.LINKBAR-Single-Touch-Milk-Module-fig (45)
  3. Enter Passcode: Use the current time as your password (for example, if the time is 13:47, enter 1347), and tap  LINKBAR-Single-Touch-Milk-Module-fig (26) to continue.
  4. ADV Settings Interface: Modify parameters such as tube pre-filling, pump speed, brightness, and standby cleaning. Parameter definitions include:LINKBAR-Single-Touch-Milk-Module-fig (46)
    • Pump Speed: The motor speed can be adjusted.
    • Tube Pre-Filling: Adjust the time based on the length of the milk tube.
    • Brightness: The screen brightness can be adjusted to adapt to different ambient light conditions.
    • Standby Cleaning: The machine will automatically clean itself after a period of inactivity.

CLEANING

  • The machine will automatically start a quick 10-second cleaning cycle after 3 minutes of no use.
  • After 6 minutes of non-use, the machine will initiate a 30-second countdown on the main interface. The faucet icon will also blink for 30 seconds as a visual cue. completion of the countdown, the machine will automatiælly commence a standard cleaning cycle lasting approximately 25 seconds.
  • Equipment must be cleaned with Alkaline milk foaming system cleaning tablets before the end of each working day.
  • If not cleaned, the machine will automatiælly perform a forced cleaning after 24 hours.
  • Following the Alkaline milk foaming system cleaning tablets præedure at the end of  Hations, an Acidic milk foaming system cleaning tablets procedure should also be performed for deep cleaning once a week
  • Please uæ dry, soft towel to wipe the milk tube, milk inlet tube tip, and milk outlet.
Daily Cleaning Procedure
  1. Go to “Settings – Cleaning – Daily Cleaning” on the main page.
  2. All pipes will undergo an automatic flushing process.
  3. Place the liquid tube, cleaning tube, and one piece of Linkbar alkaline milk foaming system cleaning tablet into a clean, empty milk container, and tap to proceed to the next step.LINKBAR-Single-Touch-Milk-Module-fig (49)
  4. The machine will heat up to 60°C, and the cleaning tube will automatically dispense water; wait for the heating to finish.
  5. The machine will automatically perform a cleaning cycle; wait for the cycle to complete.
  6. Cleaning is complete, and you should switch off the power.LINKBAR-Single-Touch-Milk-Module-fig (48)
Weekly Cleaning Procedure
  1. Go to “Settings – Cleaning – Weekly Cleaning” on the main page.LINKBAR-Single-Touch-Milk-Module-fig (50)
  2. All pipes will undergo an automatic flushing process.LINKBAR-Single-Touch-Milk-Module-fig (49)
  3. Place the liquid tube, cleaning tube, and one piece of Linkbar alkaline milk foaming system cleaning tablet into a clean, empty milk container, and tap to proceed to the next step.
  4. The machine will heat up to 60°C; wait for the heating to finish while the cleaning tube automatically dispenses water.
  5. The machine will automatically perform a cleaning cycle; wait for the cycle to complete.
  6. After daily cleaning, empty the container, add one piece of Linkbar Acid Milk Foaming System Cleaning Tablet and $500\text{ ml}$ of 80°C hot water to allow it to dissolve completely, then place the liquid tube and cleaning tube into the container and press to proceed.LINKBAR-Single-Touch-Milk-Module-fig (51)
  7. The machine will automatically perform another cleaning cycle; wait for completion.
  8. Cleaning is complete, and you should switch off the power.

Anhui Linkbarcafe Electric Appliance Technology Co., Ltd

  • E-Mail: admin@linkbar.tech
  • Tel. +86 138 1768 6423
  • Add: Room 3001, Building 1, No. 823, Longhekou Road, Nangang Science and Technology Park, High-tech Zone, Shushan District, Hefei City, Anhui Province, China

Documents / Resources

PDF thumbnailSingle Touch Milk Module
Instruction Manual · Single Touch Milk Module, Touch Milk Module, Milk Module, Module

References

Published: September 11, 2026
Updated: September 12, 2026

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.

LINKBAR Single Touch Coffee Instructions
September 17, 2026