Lezun A8 Bluetooth Speaker

Product Specifications

• Compliance: FCC Part 15
• RF Exposure: General RF exposure requirement met
• Usage: Portable exposure condition without restriction

Product Usage Instructions

1. FCC Compliance

Ensure that the device is operated in accordance with FCC Part 15 regulations. The device should not cause harmful interference and must accept any interference received.

2. RF Exposure

The device has been evaluated to meet general RF exposure requirements, allowing for safe usage in portable exposure conditions. Users can operate the device without restrictions in this regard.

Table of Product Contents

Bluetooth Speaker*l

Type-C Charging Cable*l

Instruction Book*l

Product Specification

Product model: AS
Charging port: Type-C
Battery capacity: 2000mAh
Battery model: lithium battery Transmission range: 10 meters (no obstacles)

Operation of Key Functions

1. On/Off Key
2.  Next Key
3.  Previous Key
4.  Pause/Play Key
5.  Light Key

1. On/Off Key
   Press and hold the power button for 5 seconds to turn on or off the speaker. Reset: Press and hold the power button for 8 seconds, and the pairing information will be cleared at the same time
2.  Next Key
   it Long press to play the next song . Short press to turn up the volume.
3.  Previous Key
   Long press to play the previous song. Short press to turn down the volume.
4.  Pause/Play Key
   Short press the button to pause/play music. When a call comes in, short press the button to answer/hang up the call; Press and hold the button to reject the call.
5.  Light Key
   Short press the light button to switch to different light modes. A total of 7 colors of light can be selected (purple, green, blue, red, yellow, light blue, orange)Wireless pairing

Wireless pairing

Please charge for 3 hours before first use. Press and hold the power button for 5 seconds to turn on the speaker. Turning on your phone, enter the Bluetooth pairing mode, select the Bluetooth pairing name “AS” on the device, complete the connection, and hear the prompt tone. The speaker will complete the connection within 5 seconds. If the connection is not completed within 5 minutes, the Bluetooth speaker will automatically shut down. When the connection range is exceeded, Bluetooth automatically disconnects, accompanied by a “disconnected” prompt sound; after entering the connection range again within 5 minutes, Bluetooth automatically connects, accompanied by a “connected” prompt sound.

Charging equipment

Before first use, please make sure it is fully charged and used in a dry environment! Keep the product out of reach of children. Use a soft cloth to clean the product instead of harsh chemicals. Be sure to disconnect the power supply before cleaning. Do not pierce or disassemble the outer surface of the product in any way. Do not insert any metal objects into the device to prevent impact on the device.

Frequently Asked Questions

Why can’t the speaker pair with my phone?

Make sure the Bluetooth speaker is fully charged and powered on Make sure your phone’s Bluetooth is turned on  If both of the above are OK, press and hold the power button for 8 seconds to reset it, wait for one minute, turn on the Bluetooth speaker, and re-pair it with your phone.

Why is there no sound from the Bluetooth speaker?

Please make sure that the distance between your phone and the Bluetooth speaker is within 10m.

Is the Bluetooth speaker waterproof?

The AS Bluetooth speaker is sweat-proof and slightly waterproof. For electronic products, we do not recommend soaking the earbuds in water. Please use them in a dry environment.” For more detailed product FAQs, please contact our customer service. We are online 24 hours a day and are ready to answer you at any time.

Activation & Warranty 

Permanent replacement of damaged, defective, upgraded, or missing items (no need to return original). Please activate via email below within 30 days vjdtjz@gmail.com

FCC Statement

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Documents / Resources

Lezun A8 Bluetooth Speaker [pdf] User Guide 2AXGO-A8, 2AXGOA8, A8 Bluetooth Speaker, A8, Bluetooth Speaker, Speaker

References

• User Manual