LEOCH S08FPR Core Lock Instruction Manual

LEOCH S08FPR Core Lock

Product parameters

LEOCK S08FPR lock core lock product specificationsS08FPR lock core lock components, front lock assembly, knob

Installation flow chart

Battery installation diagram:

Lock core lock installation diagram:
Note: First install the front component on the door panel, and then fix it with M5X65 screws. The knob and the front lock component can be installed by docking.

Mechanical dimensions and product customization parameters

S08FPR lock core lock mechanical dimension diagram:

Customization parameters of S8FPR lock core length:

Operation instructions of mobile APP

This product supports the doodle APP, which can be searched in the app store “Graffiti Smart” can be downloaded by scanning the QR code in the picture on the right APP, register an account according to the prompt.

If used abroad, please search for “SMARTLIFE” Download and use.

 Start Bluetooth pairing
In the experience mode, touch the button at will to power on the product and start bluetooth pairing with 90S. In non-experience mode: press 1+#+super administrator password#-> the fingerprint ring and indicator light will turn on and off, accompanied by two beeps of the buzzer, and 12 keys will be lit up to start bluetooth pairing with 90S.

After bluetooth pairing, open the Tuya APP and search for the device

As shown in the figure above, after adding the search, follow the APP prompts.
Note: If the local super password is not set and the Bluetooth pairing is completed directly, the product will enter the Bluetooth mode and the local member management function will be turned off. If you want to use both the local management mode and the Bluetooth APP management mode, please register the local super administrator first.

Add fingerprint; Password; RFID card user; Delete fingerprint; Password; RFID card user (Note: Add card; Password; fingerprint before registering the super administrator on the device)

• Click on the main page of APP in sequence → Member Management → I →
  Fingerprint Add → After the ambient light of the fingerprint recognition area lights up, start to input the finger (Note: move the finger up and down and left and right within a small range)
• Click on the main page of APP in sequence: Member management, I, Password
  Add, and enter the 6-digit password you want
• Click on the main page of APP in sequence: Member Management, I, Card Add, and card close to the number key 5 and 8 to add a card
• Click on the main page of the APP, click → Member Management → I → Click fingerprint; Password; Door card → Delete in sequence

 More Settings:

Restore factory Settings:(Note: “Unbinding needs to be carried out when the mobile phone bluetooth is connected with the device”, and all users cannot restore after clearing data.)

APP unlock: swipe the key icon to the right to unlock the device:

 Log:
Click log on the APP home page to check the device operation record:

 Use of local emergency passwords（Note: If you directly connect to Bluetooth, users cannot be added locally; administrator)

1. Set the super management password (1+#):
   For local operation, you must first set the super admin password.

Set the superuser password

1. According to 1+#-> The fingerprint ring and the indicator light turn on and off, accompanied by a “drip” sound of the buzzer, and the 12 keys are lit up.
2.  Enter the new 6-digit password and confirm with a # sign. After a successful operation, the fingerprint ring and the indicator will flash green;
3. Enter the new 6-digit password again and confirm with # sign. After success, the fingerprint halo and indicator will flash green;
   The password configuration is successful: the fingerprint lights up green, and the buzzer rings for a long time,
   Password configuration failed: the fingerprint lights up red and the buzzer rings three times.
   Note: The superuser password must be 6 characters long.

Change the superuser password

1. Press 1+#+ super administrator password + # -> the buzzer “drip” and the 12 keys light up.
2.  Enter the new 6-digit password and confirm with a # sign. After success, the fingerprint ring and indicator will flash green;
3. Enter the new 6-digit password again and confirm with the # sign. After success, the fingerprint ring and the indicator will flash green;
   The password configuration is successful: the fingerprint lights up green, and the buzzer rings for a long time,
   Password configuration failed: the fingerprint lights up red and the buzzer rings three times.

Registered users (2+#):

1. Press 2+#+super administrator password +#-> the fingerprint ring and indicator light will be green, accompanied by two “dang dang” sounds from the buzzer, and the 12 key lights will be on, and the fingerprint ring and indicator light will be blue.
2.  Enter the fingerprint/password/card as required; you can input it continuously. One long beep means one successful entry, and there is no need to continue entering. Press * key to exit.

• Note: a. You must set up a superuser before you can perform this operation.
• The password needs to be entered twice, each ending with a # sign
• The user password is 6 to 8 digits

Always on mode (5+#):
According to 5+#+super administrator password +#-> the fingerprint ring and indicator light will be green, and the system will enter the constant on mode.
Note: In the normal open mode, any lock operation will exit the normal open mode.

Product initialization (000+#):
According to 000+#> fingerprint ring flashes red light +> super administrator password+#> fingerprint ring flashes green light, the buzzer rings for a long time,
and initialization is successful.

Details of accessories

S08FPR lock core lock accessories details

graphic	appellation	size	pigment	quantity
	Front lock assembly  knob		blackness	1
		Length 35mm Height 34.80mm		1
	Pointed sinker screws	70mm		1
	RFID card	/	/	2
/	key	/	/	2
/	Paper instructions	/	/	1

Packaging specifications

S08FPR packaging specifications

Frequently Asked Questions

Q: What should I do if the password configuration fails?
A: If the password configuration fails, the fingerprint lights up red, and the buzzer rings three times. Retry the password configuration process.