legrand 080305 Plus Wireless Manager
Product Information
- The Wattstopper PLUS Wireless Manager serves as the central intelligence point in the system for wireless devices.
- It gathers data from photo sensors, occupancy sensors, and wall stations to facilitate various lighting control strategies.
- The manager then determines appropriate brightness levels or ON/OFF status for each luminaire and zone.
This symbol indicates DC voltage.
SPECIFICATIONS
- Voltage……………………..48VDC, via Power over Ethernet (PoE)
- Current Consumption…………………..0.7A
- Wireless Range……… 30 m (100 ft) line of sight, … 15.2 m (50 ft) through standard walls
Radio
- Frequency Range……. 2405-2480 MHz
- Channel Space……………………. 5MHz
- Modulation Type…………………….O-QPSK
- Transmit Power………..13.40dBm EIRP (max)
- Operating Temperature………………………….32° to 104°F (0° to 40°C)
- Certifications ………..UL/cUL Listed, Energy Management Equipment (UL 916)
CE FCC Part 15/ICES-003, Class B Complies with Electromagnetic Compatibility (EMC) Standards: EN 61000-4-2, EN 61000-4-4, EN 61000-4-5
PRODUCT SAFETY
When using electrical equipment, basic safety precautions should always be followed, including the following:
- Do not mount near gas or electric heaters or let power supply cords touch hot surfaces.
- Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
- The use of accessory equipment is not recommended by Legrand as it may cause an unsafe condition.
- Do not use this equipment for anything other than the intended use.
WIRELESS SYSTEM OVERVIEW
This illustration shows how each component is easily integrated into the Wattstopper PLUS System.
MOUNTING
Ceiling Mount
Cut an 85.7 x 31.8 mm (3.375 x 1.25 inches) hole in the ceiling tile. Assemble the Wireless Manager and the ceiling tile mount bracket. Push the ceiling tile mount bracket until it snaps into the groove. Place the assembled Wireless Manager through the ceiling tile hole. Place the upper bracket onto the Wireless Manager (above the ceiling tile from the plenum area) until it locks with the lower bracket installed.
Wall Mount
Align the Wireless Manager screw holes with the screws on the Junction Box (Switch wall box) and slide slightly to secure it with the junction box. Using a needle-nose plier, push down to open a hole and pull the Ethernet cable through.
WIRING
This product bears the selective sorting symbol for Waste Electrical and Electronic Equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment.
WARRANTY
WARRANTY INFORMATION
- Wattstopper warrants its products to be free of defects in materials and workmanship for a period of five (5) years.
- There are no obligations or liabilities on the part of Wattstopper for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages concerning loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.
CONTACT
- 800.879.8585
- www.legrand.us/wattstopper
FAQ
- What is the maximum wireless range of the Wireless Manager?
- The maximum wireless range of the Wireless Manager is 30m (100 ft) line of sight or 15.2m (50 ft) through standard walls.
- What voltage does the Wireless Manager operate on?
- The Wireless Manager operates on a voltage of 48VDC via Power over Ethernet (PoE).
Documents / Resources
 |
legrand 080305 Plus Wireless Manager [pdf] Instruction Manual 080305 Plus Wireless Manager, 080305, Plus Wireless Manager, Wireless Manager, Manager |