Installation guide
SALTO Gateway
MODEL: ELECTRONIC INFO. RFnet Gateway – BLUEnet Gateway
Description
The Gateway is the link between the PC and SALTO’s wireless network SALTO RFnet or SALTO BLUEnet (wireless escutcheons). It gives real-time information to the PC. Gateways are completely managed through the SALTO Software, it collects all the information sent by escutcheons that belong to the Gateway. It has been designed with PoE technology, capable of power the SALTO Gateway through Ethernet infrastructure.
Electrical characteristics
Operation conditions
| Min | Typ | Max | Unit | |
| Temperature | 0 | 25 | 60 | ºC |
| Humidity | 35 | 85 | % |
PoE (IEEE 802.3af)
| Unit | ||
| Class | 2 | |
| MaxPower | 5 | W |
| Ethernet Standard | 10BASE‐T/100BASE‐ TX |
Cable requirements
Ethernet UTP CAT5e
Complies with IEC 60332, IEC 60695-11-21 or VW-1 (UL 2556)
SALTO BLUEnet Characteristics (if internal node installed)
| Frequency Range | 2400‐2483,5 Mhz |
| RF Standard | Bluetooth Low Energy |
| Indoor Radio Range | 10m/15m* |
| Max output power | 8dBm |
Auxiliary Power Supply
| Min | Typ | Max | Unit | |
| InputVoltage Note 2 | 10 | 12 | 15 | V |
| Currentconsumption 75 Note 3 | 500 Note 4 | mA |
SALTO RFnet Characteristics (if internal node installed)
| Frequency Range | 2400‐2483 Mhz |
| RF Standard | IEEE 802.15.4 |
| Indoor Radio Range | 10/15m* |
| Max output power | 5dBm |
(*) Depending upon installed environment.
Note 1: 1x2x24AWG or UTP CAT5e recommended
Note 2: Use provided AC‐DC power supply
Note 3: No external/internal node connected
Note 4: 6 external node connected
(*) The environment has a direct impact on the BLUEnet range radiation (metal, concrete walls…)
The receiver device must be located facing the product antenna. Please check your product’s BLUEnet antenna position.
Recommended connectivity distance: 10m – 15m
UL Statement
Comply with UL/CSA 62368-1:
Product could be connected to PoE networks without routing to the outside plant
Mechanical installation
Electrical installation
– When PoE and auxiliary power supplies are connected at the same time, Poe is disconnected.
– Pressing CLR button 5 seconds, Gateway enters in addressing mode.
Auxiliary power supply needed when Ethernet infrastructure is not PoE (Power over Ethernet).
Configuration
Addressing and configuration
Gateway is a DCHP ready device. If there is no DCHP server on the local Ethernet network, user can manually configure a fixed IP address changing different parameter using SALTO Gateway Web Server:
- Pressing CLR button for 5 seconds, SALTO Gateway enters in addressing mode (green LED turns to orange).
- Access to 192.168.0.234 IP address with a standard browser and configure network parameters as needed.
- Pressing again CLR button for 5 seconds or confirming the configuration, the device is going to quit the addressing mode.
When addressing process success, configure the wireless network with SALTO’s software (check the help of the application).
Installation example
Signalling
| LED COLOR | DESCRIPTION |
| No light | Lack of power supply |
| Green | Everything is OK |
| Orange | Gateway in “Addresing mode” |
| Red | Gateway in “Bootloader mode” state |
| Flashing Green | No initialized by SALTO’s software |
The LEDs on the Ethernet Connector show the state of the Ethernet communication
| LED COLOR | DESCRIPTION |
| No light | No Ethernet Connection |
| Green | Ethernet active |
| Flashing Orange | Data transfer taking place through Ethernet |
Operational test
Once the product is installed, follow these steps to check the correct operation:
– Visually chek that the LED is active after power on.
– When nodes and locks are installed, check that the LED is green.
– Check Ethernet connector LED to know communication state.
This unit should be tested at least once a year as described in “Operational Test”.
European view 
All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any item in this catalog, its design, construction, and/or materials.
© 2023 SALTO Systems S.L.
Documents / Resources
 |
SALTO GATEWAYW3CAUS Bluenet Wireless Gateway [pdf] Installation Guide GATEWAYW3CAUS Bluenet Wireless Gateway, GATEWAYW3CAUS, Bluenet Wireless Gateway, Wireless Gateway, Gateway |
