Pyle PT250BA Wireless Bluetooth Power Amplifier System

Before you use this Home Theater Wireless BT Streaming Receiver Amplifier, we recommend that you carefully read through this manual.
Please keep the instruction manual for future reference.

FEATURES

• Stereo Amplifier with A/B Speaker Output
• FM Radio with Digital Display Screen
• USB Flash Drive Reader Function
• Auto Scan, Memory, Radio Station, Previous/Next Control
• Volume/Balance/Treble/Bass Gain Control for Main Channel
• Volume/Bass/Treble/Echo Control for Microphone
• Two Microphone Input Jacks
• Two RCA Input Source

WIRELESS BT STREAMING

• Built-in BT for Wireless Music Streaming
• Simple & Hassle-Free Pairing
• Works with All of Today’s Latest Devices (Smartphones, Tablets, Laptops, Computers, etc.)
• Wireless BT Version: 4.2
• Wireless BT Network Name: ‘PT250BA’
• Wireless Range: Up to 32’ ft

WHAT’S IN THE BOX

• Home Theater Wireless BT Streaming Receiver Amplifier
• Remote Control
• FM Antenna

TECHNICAL SPECS

• Power Supply: 50W x 2 @ 8 Ohm, 100W x 2 @ 4 Ohm
• Power Output: 110/220V Power Switch
• Remote Control Battery Operated, requires (2) x ‘AAA’ Batteries (Not Included)
• Product Dimensions (L x W x H): 17” x 11.5” x 4.7” –inches

SAFETY INSTRUCTIONS

1. Make sure that all connections are properly connected and the main volume is set to minimum level before turning ON the unit.
2. When more than one pair of speakers are used, (specially the main speaker output) make sure that the speakers used are of the same wattage and impedance, otherwise the unit maybe damaged under high power or long term operation.
3. To avoid humming sounds and unwanted noise, make sure that all the wires are properly inserted.
4. For speaker cords, strip off the vinyl coating and twist the wire tip. Push down the pink jack or loosen the screw terminal, before inserting the wire tip, then fasten it and tighten the screw. Be careful not to let the wires stick out of the terminal otherwise this may cause a short circuit when wires of different terminal contact each other.
5. After the unit is turned ON, adjust the main volume to the desired level same is true with the bass and treble volume, etc.

PRECAUTIONS

1. Power source: The unit should be connected to a power supply AC-110V/60Hz or AC-220V/50HZ.
2. Ventilation: The unit should be situated so that its location or position does not interfere with its proper ventilation. Place the unit at least 10cm away from the walls.
3. Water and moisture: The unit should not be used near water-for example, near a swimming pool in a wet basement, etc.
4. Electric shock: If a metal object, such as hair pin or needle comes into contact inside this unit, a dangerous electric shock may result. For families with children, never permit children to put anything, especially metal, inside this unit.
5. Enclosure removal: Never remove the enclosure. If the internal parts are touched accidentally, a serious electric shock might occur.
6. Abnormal smell: if an abnormal smell or smoke is detected, immediately turn the power OFF and pull out the power cord. Contact your dealer or nearest service station.

FRONT PANEL

1. POWER SWITCH: Press to switch the power unit ON or OFF.
2. MIC BASS: Adjusts the bass of MIC.
3. MIC TREBLE: Adjusts the treble of MIC.
4. ECHO CONTROL: Turn the knob to adjust the MIC echo level.
5. MIC INPUT JACK 1: KARAOKE MIC connect to this jack.
6. PLAY/PAUSE: USB/BT play/pause and Tuner Scan
7. PREV<: When it is TUNER,it means the preview station;
8. When it is USB, it means the preview song.
9. NEXT>: When it is TUNER, it means the next station; When it is USB, it means the next song.
10. USB Play STOP
11. USB Tone EQ Selector
12. Signal MUTE key
13. INPUT Selector: Selector IPOD/M P3, DVD/CD, USB, BT, FM Signal.
14. MIC INPUT JACK 2: The KARAOKE MIC connect to this jack.
15. MIC VOLUME: Adjusts the volume level. Turn the knob clockwise to increase the MIC volume.
16. BALANCE CONTROL: Turn the knob to adjust the master balance level.
17. TREBLE CONTROL: Turn the knob to adjust the master treble level.
18. BASS CONTROL: Turn the knob to adjust the master bass level.
19. MASTER VOLUME CONTROL: Adjusts the volume level. Turn the knob clockwise to increase the volume.
20. USB JACK

REAR PANEL AND WIRELESS BT FUNCTION

1. TUNERANT: Connect for FM antennas.
2. AUDIO INPUT JACKS: Connect the audio output jacks of IPOD/MP3, DVD/CD to these jacks.
3. A SPEAKER OUTPUT TERMINALS: Connect your speaker system to these terminals.
4. B SPEAKER OUTPUT TERMINALS: Connect your the other speaker system(s) to these terminals.
5. 110V/220V SWITCH: According to power voltage, push this button to the station of the110V or 220V.
6. POWER LINE: Connect to AC 110V/60Hz and 220V/50Hz outlet.

ATTENTION

When you want to listen to the radio, press input key to select tuner (FM) and then press scan button and hold for 3 seconds to seek for the station.

WIRELESS BT STREAMING OPERATION

Press 12 INPUT button Selector BLUE input sources. When there is a ding-dong sound it means the unit on BT input status. Then you can use your BT device such as mobile phone to search for BT device named PT250BA to pair it. When the pairing is completed there will be a ding-dong sound as well, then you can play music from your mobile phone on the amplifier via Wireless BT streaming.

NOTES

1. Available operation range of BT function of the unit is 10 meters. Be sure there are no obstacles between the unit and your mobile phone or it will affect the BT effect then cause the sound brokenly.
2. This operation only available for mobiles with BT function.

REMOTE CONTROLLER

1. USB Standby
2. MODE:

IPOD/MP3, DVD/CD, USB, BT, FM Signal

3. USB Tone EQ
4. VOL+ / VOL-

Master Volume Down And Up

5. USB/BT Play Next and Tuner CH+
6. USB/BT Play/Pause and Tuner Scan
7. USB Play Repeat
8. USB/FM Number buttons
9. USB Play STOP
10. USB/BT Play Next and Tuner CH-
11. Signal MUTE

REMOTE CONTROL OPERATION

1. Remote control should be operated within 6 meters and the scope of 30° in front of receiver.
2. Make sure that there is no big obstacle between remote control and machine.
3. Remote sensor should be far away from the light, high amounts of light can affect its performance.

CONNECTING TO AMPLIFIER

Support

Questions? Comments?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com

FAQs

What is the purpose of a Pyle PT250BA Bluetooth amplifier?

By utilising Bluetooth’s radio frequency connection, a Bluetooth amplifier can turn your beloved wired headphones into wireless Bluetooth headphones.

How does a Pyle PT250BA wireless amplifier work?

In terms of appearance and functionality, WiFi signal amplifiers are small boxes with antennas connected to an electrical outlet. When an amplifier is plugged in, it immediately picks up the wireless router signal and amplifies it so it can be transmitted.

How do I connect my Pyle PT250BA AMP to Bluetooth?

After choosing the “Pyle Speaker” Wireless BT name, the device will link. E. You can play music from your Bluetooth device after pairing. The control buttons on the gadget can also be used to choose tunes from your Bluetooth device.

Can you add Bluetooth to an Pyle PT250BA amplifier?

Use a wireless Bluetooth adapter to add Bluetooth to an A/V or Stereo Receiver. These tools are easy to use and come in a variety of price ranges depending on the quality you require.

How do I connect my Pyle PT250BA amplifier to wireless speakers?

Connect the Bluetooth transmitter to the receiver’s headphone jack. After connecting the receiver to a power source, turn it on.

Where are Pyle PT250BA amplifiers made?

In the creation and production of “Made in the USA” sound systems for automobiles, trucks, and the house, Pyle Industries has long been a pioneer. Pyle produced the first portable high-power woofers.

How is a Pyle PT250BA amplifier linked to a TV?

Locate the audio jack and the audio input, place the receiver and amplifier close to the TV, and attach the cables to the receiver and amplifier. Ensure that everything is turned off before connecting. Make sure the receiver amplifier’s level is set to low before testing.

How is a Pyle PT250BA Bluetooth stereo amplifier made?

A Bluetooth amplifier can convert your cherished wired headphones into wireless Bluetooth headphones by using Bluetooth’s radio frequency link.

How can I connect my Pyle PT250BA wireless amplifier to my computer?

Buy a sturdy, long 3.5 mm to RCA cable. The 3.5 mm end of the cable should be connected to the computer’s speaker or headphone output, and the RCA input of your home stereo should accept it. If the sound quality is subpar, use a USB DAC like the Audioquest Dragonfly.

Is it possible to use a phone to power a Pyle PT250BA amplifier?

An electric guitar or bass can be amplified using your Android or Apple iOS phone or tablet. To hear the sound, you need headphones or speakers, an interface to connect the guitar, and an app to handle the signal (an amplifier).

For what use would someone utilize a Pyle PT250BA stereo amplifier?

The function of an amplifier is to amplify weak electrical signals. A power amplifier needs the signal to be amplified enough when utilising a pre-amplifier. In order to drive a loudspeaker, the signal must be considerably amplified in a power amplifier.

What purpose does a Pyle PT250BA amplifier serve in an audio setup?

The low voltage signals from your source equipment are converted by an amplifier into a signal with enough strength to drive two speakers.

How can you connect a television’s audio to a Pyle PT250BA amplifier?

Connect the cables to the receiver and amplifier using the audio jack and audio input. Ensure that everything is turned off before connecting. Make sure the receiver amplifier’s level is set to low before testing.

References

• User Manual