nLiGHT rES7 Sensor Fixture Embedded Smart Installation Guide

EQUIPMENT SHOULD BE MOUNTED IN LOCATIONS AND AT HEIGHTS WHERE IT WILL NOT READILY BE SUBJECTED TO TAMPERING BY UNAUTHORIZED PERSONNEL.
THE USE OF ACCESSORY EQUIPMENT NOT RECOMMENDED BY THE MANUFACTURER MAY CAUSE AN UNSAFE CONDITION.

Contains FCC ID: 2ADCB-RMODIT or 2ADCB-RES7CD
Contains IC: 6715C-RMODIT or 6715C-RES7CD

IFT #: RCPACRM18-1879 or RCPACRE21-0154
Acuity Brands Lighting Inc. RMODIT or RES7CD

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

this device must accept any interference received, including interference that may cause undesired operation.

To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the radiator shall not be less than 20cm during normal operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

WARRANTY

5-year limited warranty.
Full warranty terms are located at: www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx

Note: Specifications are subject to change without notice.

Actual performance may differ as a result of end-user environment and application.

To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
Installation and service should be performed by a qualified licensed electrician.
Maintenance should be performed by a qualified person(s) familiar with the products’ construction & operation & any hazards involved. Regular maintenance programs are recommended.
DO NOT INSTALL DAMAGED PRODUCT! This product has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.

rES7 BASIC OVERVIEW

The rES7 is a wireless sensor that can be interconnected with the nLight® AIR network of wireless sensors and switches.
The rES7 is compatible for use in fixtures with eldoLED drivers, or other analog (0-10VDC) third-party aux drivers.

TYPICAL INSTALLATION INSTRUCTIONS

(may vary by luminaire)

Attach foam pads to the surface of rES7 as shown. Adjust the thickness of the pad as needed to fill the gap between the sensor body and the end cap.
Attach wires to the sensor according to the diagram below. Wire locations are also shown on the product label.
Ensure a thin wire antenna points toward the center of the fixture, between the LEDs and diffuser.

Place the rES7 in the fixture, with the rES7 cylinder aligned to the clearance hole.
Insert the rES7 lens assembly through the hole, securing it to the sensor body.
Install diffuser.

TYPICAL INSTALLATION FOR EXTERNAL ANTENNA

(optional)

Attach wires to the sensor according to the wiring diagram below. Wire locations are also shown on the product label.
Route the coax cable through the inside of the fixture to the antenna hole.

Affix the o-ring, washers, and nut as indicated on the drawing (2) to the external surface of the fixture.
Attach external antenna (1) to the brass SMA connector. Torque spec for proper installation is 5in-lbs.
Place the rES7 in the fixture, with the rES7 cylinder aligned to the clearance hole.

Secure the lens assembly to the rES7 body.

OUT-OF-BOX OPERATION

Occupancy Control: Enabled

Microphonics (with -PDT): Enabled
Occupied Dim Level: 100%
Unoccupied Time Until Dim: 2.5 Minutes

Unoccupied Dim Level: 1%
Dim to Off Time Delay: 7.5 Minutes
Daylighting Control: Enabled

Daylighting Set Point: 10 FC
Daylighting Transition On Time: 45 Seconds
Daylighting Transition Off Time: 10 Minutes

For further troubleshooting guidance, please contact the Controls Technical Support Team at 1(800)-535-2465

rES7 Sensor

Fixture Embedded Smart Sensor

360° COVERAGE
LOW VOLTAGE
WIRELESS

WIRING

Connect the yellow (+) and brown (-) LEDcode NTC wires to the rES7 connectors marked Y (+) and Br (-), respectively
Connect the red/blue (+) and black (-) LED Output 2 wires to the rES7 connectors marked R/Bl (+) and B (-), respectively

Connect the yellow (+) and brown (-) LEDcode NTC wires to the rES7 connectors marked Y (+) and Br (-), respectively.
Connect the red/blue (+) and black (-) AUX wires to the rES7 connectors marked R/Bl (+) and B (-), respectively.
For AUX wiring with EldoLED Optotronic Linear drivers, connect the yellow (+) and the blue (-) to the rES7 connectors marked as Red/Blu (+) and Blk (-), respectively.

For AUX wiring with EldoLED Optotronic Compact drivers, connect the yellow (+) and the green (-) to the rES7 connectors marked as Red/Blu (+) and the Blk (-), respectively.

Connect the violet (+) and gray/pink (-) 0-10V wires to the rES7 connectors marked Y (+) and Br (-), respectively

Connect the red/blue (+) and black (-) AUX wires to the rES7 connectors marked R/Bl (+) and B (-), respectively

NOTE

Compatible EldoLED Drivers:

POWER [W]	DRIVER	PART #	NOTE
20	SOLOdrive 260/U	SL0260U2	1
30	ECOdrive 30B-M1M0Z	EC30B-M1M0Z1	2
30	SOLOdrive 30B-M1M0Z	SL30B-M1M0Z1	2
30	ECOdrive 368/L	EC0368L3-NLIGHTAIR	3
30	SOLOdrive 368/L	SL0368L3-NLIGHTAIR	3
30	ECOdrive 30S-M1M0Z	EC30S-M1M0Z1	2
30	SOLOdrive 30S-M1M0Z	SL30S-M1M0Z1	2
30	SOLOdrive 360/U	SL0360U2	1
50	SOLOdrive 560/A	SL0560A3	1
50	ECOdrive 568/L	EC0568L4	2
50	SOLOdrive 568/L	SL0568L4	2
50	ECOdrive 50L-M1M0Z	EC50L-M1M0Z1	2

POWER [W]	DRIVER	PART #	NOTE
50	SOLOdrive 50L-M1M0Z	SL50L-M1M0Z1	2
50	SOLOdrive 560/S	SL0560S4	1
50	SOLOdrive 560/U	SL0560U3	1
75	SOLOdrive 75B-M2A0D	SL75B-M2A0D1	1
75	ECOdrive 768/LHC	EC0768L2	2
75	SOLOdrive 768/LHC	SL0768L2	2
75	ECOdrive 75L-M1M0Z	EC75L-M1M0Z1	2
75	SOLOdrive 75L-M1M0Z	SL75L-M1M0Z1	2
100	ECOdrive 1065/M	EC1065M2
100	ECOdrive 1068/M	EC1068M2
100	ECOdrive 1065/S	EC1065S2
100	ECOdrive 1068/S	EC1068S2

Request the second LED output as an AUX in Titan.
Request these AUX settings in Titan: VAUX = 16V and AUX “ON” during standb.y
Load on LED output 1 shall exceed 42V

Frequently Asked Questions

Q: What is the recommended input voltage range for the rES7 Sensor?
A: The recommended input voltage range for the rES7 Sensor is 5-60 VDC.
Q: Can the rES7 Sensor be used outdoors?
A: No, the rES7 Sensor is designed for indoor use only.

Documents / Resources

nLiGHT rES7 Sensor Fixture Embedded Smart [pdf] Installation Guide
rES7 Sensor Fixture Embedded Smart, rES7, Sensor Fixture Embedded Smart, Fixture Embedded Smart, Embedded Smart

References

User Manual

nLiGHT rES7 Sensor Fixture Embedded Smart

Installation

Configuration

Operation

SPECIFICATIONS