HBG-240P Series Constant Voltage Plus Constant Current LED Driver
“
Specifications:
| MODEL | OUTPUT | CONSTANT CURRENT REGION | RATED CURRENT | RATED POWER | RIPPLE & NOISE (max.) | CURRENT ADJ. RANGE | LINE REGULATION | LOAD REGULATION | SETUP, RISE TIME | HOLD UP TIME (Typ.) | VOLTAGE RANGE | FREQUENCY RANGE | POWER FACTOR |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HBG-240P-36 | 36V | 21.6 ~ 36V | 6.7A | 241.2W | 250mVp-p | 4.0 ~ 6.7A | 2500ms, 120ms / 115VAC 500ms, 120ms / 230VAC | 15ms/115VAC,230VAC | 90 ~ 305VAC 127 ~ 431VDC | 47 ~ 63Hz | PF0.98/115VAC, PF0.94/230VAC, PF0.9/277VAC@full load | ||
| HBG-240P-48 | 48V | 28.8 ~ 48V | 5A | 240W | 250mVp-p | 3 ~ 5A | 2500ms, 120ms / 115VAC 500ms, 120ms / 230VAC | 15ms/115VAC,230VAC | 90 ~ 305VAC 127 ~ 431VDC | 47 ~ 63Hz | PF0.98/115VAC, PF0.94/230VAC, PF0.9/277VAC@full load | ||
| HBG-240P-60 | 60V | 36 ~ 60V | 4.0A | 240W | 350mVp-p | 2.4 ~ 4.0A | – | – | – | – | – |
Product Usage Instructions:
1. Installation:
– Ensure power source is within specified voltage range.
– Connect the LED driver to the LED lighting system according to
the provided wiring diagram.
2. Adjustment:
– For A-Type drivers, adjust the current range using the
built-in potentiometer within the specified limits.
3. Powering On:
– Apply power to the LED driver and verify proper functionality
of the connected LED lights.
4. Maintenance:
– Regularly inspect for any signs of damage or wear on the
driver and replace if necessary.
Frequently Asked Questions (FAQ):
Q: Can this LED driver be used with dimmer switches?
A: No, this LED driver is designed for constant voltage and
constant current operation and is not compatible with dimmer
switches.
Q: What is the maximum number of units that can be connected to
a 16A circuit breaker?
A: At 230VAC, a maximum of 2 units can be connected with a
circuit breaker of type B, or 3 units with a circuit breaker of
type C.
Q: Is the current adjustment range the same for all
models?
A: No, the current adjustment range varies between models, so
refer to the specifications for each model for specific
details.
“`
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
User’s Manual
A
File Name:HBG-240P-SPEC 2024-01-08
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
SPECIFICATION
MODEL
HBG-240P-36
HBG-240P-48
OUTPUT
DC VOLTAGE
36V
48V
CONSTANT CURRENT REGION Note.2 21.6 ~ 36V
28.8 ~ 48V
RATED CURRENT
6.7A
5A
RATED POWER
Note.5 241.2W
240W
RIPPLE & NOISE (max.) Note.3 250mVp-p
250mVp-p
CURRENT ADJ. RANGE
Adjustable for A-Type only (via built-in potentiometer)
4.0 ~ 6.7A
3 ~ 5A
VOLTAGE TOLERANCE Note.4 ±2.0%
LINE REGULATION
±0.5%
LOAD REGULATION
±0.5%
SETUP, RISE TIME Note.6 2500ms, 120ms / 115VAC 500ms, 120ms / 230VAC
HOLD UP TIME (Typ.)
15ms/115VAC,230VAC
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC Note.5 (Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE POWER FACTOR
47 ~ 63Hz
PF0.98/115VAC, PF0.94/230VAC, PF0.9/277VAC@full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
HBG-240P-60 60V 36 ~ 60V 4.0A 240W 350mVp-p
2.4 ~ 4.0A
TOTAL HARMONIC DISTORTION
THD< 20%(@load60%/115VC,230VAC; @load75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
INPUT
EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT(Typ.)
92.5%
93%
2.8A / 115VAC 1.4A / 230VAC 1.2A / 277VAC COLD START 75A(twidth=680s measured at 50% Ipeak) at 230VAC; Per NEMA 410
93.5%
MAX. No. of PSUs on 16A CIRCUIT BREAKER
2 units (circuit breaker of type B) / 3 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
OVER CURRENT
95 ~ 108% Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT PROTECTION
OVER VOLTAGE
Hiccup mode, recovers automatically after fault condition is removed.
43 ~ 52V
52 ~ 63V
Shut down and latch off o/p voltage, re-power on to recover
OVER TEMPERATURE Note.11 Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP.
Ta=-40 ~ +45 (Please refer to ” OUTPUT LOAD vs TEMPERATURE” section)
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 50)
VIBRATION
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
62 ~ 85V
SAFETY STANDARDS
UL8750,CSA C22.2 No.250.13-12; ENEC BS EN/EN61347-1,BS EN/EN61347-2-13,BS EN/EN62384, GB19510.1,GB19510.14, EAC TP TC 004 approved
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH
Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load 75%) ; BS EN/EN61000-3-3, GB/T 17743, GB17625.1, EAC TP TC 020
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547,light industry level(surge immunity:Line-Earth:4KV, Line-Line:2KV), EAC TP TC 020
OTHERS NOTE
MTBF
2290.4K hrs min. Telcordia SR-332 (Bellcore) 175.1Khrs min. MIL-HDBK-217F (25)
DIMENSION
Refer to mechanical specification
PACKING
0.62Kg; 20pcs/13.4Kg/1.11CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Please refer to “DRIVING METHODS OF LED MODULE”. 3. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 4. Tolerance : includes set up tolerance, line regulation and load regulation. 5. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details. 6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 8. This series meets the typical life expectancy of >50,000 hours of operation when Ta is about 45 or less. 9. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com 10. The ambient temperature derating of 3.5/1000m with fanless models and of 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 11. All functional testing must be filled with potting,including OTP function .
Product Liability DisclaimerFor detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:HBG-240P-SPEC 2024-01-08
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
BLOCK DIAGRAM
fosc : 100KHz
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER
RECTIFIERS
+V
SWITCHING
& FILTER
-V
O.L.P.
FG
O.L.P.
PWM & PFC
PFC
CONTROL
CONTROL
DETECTION CIRCUIT
O.V.P.
DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.
100
Vo(%)
60 (min.)
(A) Constant
Voltage area
(B) Constant Current area
(C) Hiccup Protection
50
100
Io(%)
Typical output current normalized by rated current (%)
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL.
File Name:HBG-240P-SPEC 2024-01-08
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
DIMMING OPERATION
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
-V(Black) +V(Red)
SJTW 18AWG*2C SJTW 14AWG*2C
ACL
ACN +V
FG
-V
DIM+(Purple) DIM-(Pink)
SVT 18AWG*2C
13
VR2 VR1
3 in 1 dimming function (for B-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.)
Applying additive 1 ~ 10VDC
+V +
LED Strips +
-V
–
–
DIM+ +
Additive Voltage DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage
Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
+V +
LED Strips +
-V
–
DIM+
Additive PWM signal DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input
File Name:HBG-240P-SPEC 2024-01-08
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
Applying additive resistance:
+V +
LED Strips +
-V
–
DIM+
Additive Resistance
DIM-
“DO NOT connect “DIM- to -V”
Output current (%)
100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.
N FG L
Relay
Switch
Adjuster
10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal
Green/ Yellow
Brown
Blue
AC/L AC/N
HBG-240P B-Type
DIM+ DIM-
V(-) V(+)
Purple Pink
Black Red
LED Lighting Fixture
Using a switch and relay can turn ON/OFF the lighting fixture.
File Name:HBG-240P-SPEC 2024-01-08
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
OUTPUT LOAD vs TEMPERATURE
LOAD (%)
100
80
100VAC
230VAC
60
40
20
-40 -25 -10
0
15
30
40 45 50
AMBIENT TEMPERATURE, Ta ()
(HORIZONTAL)
STATIC CHARACTERISTIC
LOAD (%)
100 90 80 70 60 50 40
90 100 125 135 145 155 165 175 180 200 230 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
TOTAL HARMONIC DISTORTION (THD)
60V Model
30.00% 25.00% 20.00% 15.00% 10.00%
5.00% 0.00%
50% 60% 70% 80% 90% 100%
277V 230V 115V
LOAD
PF
POWER FACTOR (PF) CHARACTERISTIC
1 0.95 0.9 0.85 0.8 0.75 0.7 0.65 0.6 0.55 0.5
50%
Constant Current Mode
277V 230V 115V
60%
70%
80%
90%
100%
LOAD
EFFICIENCY vs LOAD
HBG-240P series possess superior working efficiency that up to 93.5% can be reached in field applications. 60V Model
EFFICIENCY(%)
94.5 89.5 84.5 79.5 74.5
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V 230V 115V
LOAD
File Name:HBG-240P-SPEC 2024-01-08
THD
H B G – 2 4 0 P 240W Constant Voltage + Constant Current LED Driver
series
MECHANICAL SPECIFICATION
A-type
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
-V(Black) +V(Red)
300±20 SJTW 18AWG*3C
300±20
SJTW 14AWG*2C
36
ACL
ACN +V
FG 33 -V
6*3.5mm
144
35 1.6
Unit:mm
36.5 4.75
B-type
Io.adj
VR2 VR1
13
SVR1
51.5 5*3.5mm
AC/L(Brown) AC/N(Blue) FG (Green/Yellow)
-V(Black) +V(Red)
300±20 SJTW 18AWG*3C
300±20
SJTW 14AWG*2C
36
ACL
+V 33
-V
ACN FG
6*3.5mm
144
35 1.6
36.5 4.75
DIM+(Purple) DIM-(Pink)
300±20 SVT 18AWG*2C
13
VR2 VR1
51.5 5*3.5mm
File Name:HBG-240P-SPEC 2024-01-08
Documents / Resources
 |
MEAN WELL HBG-240P Series Constant Voltage Plus Constant Current LED Driver [pdf] Owner's Manual HBG-240P-36, HBG-240P-48, HBG-240P-60, HBG-240P Series Constant Voltage Plus Constant Current LED Driver, HBG-240P Series, Constant Voltage Plus Constant Current LED Driver, Constant Current LED Driver, Current LED Driver, LED Driver |
