idatalink DL-CH12 Jeep Data Ddoorlock Integration
Specifications
- Make: DL-CH12 Chrysler
- Model: 300 PTS
- Year: 2019-2023
- Installation: CAN
- Lights: IGN Park/Auto
- Type: 2 CJB/BCM Type A3 GREEN
Product Usage Instructions
Installation:
- Ensure the hood is closed.
- Close the driver door and then re-open it to wake up the data bus.
- Press UNLOCK on the OEM remote. If no OEM remote is available, press on the module programming button.
- Set the ignition to the ON position.
- Set the ignition to the OFF position. Disconnect power lastly.
- Connect the module to a computer for extended programming. Do not press the module programming button until connecting power first.
Module Programming Procedure – PTS:
- Close the driver door.
- Re-open the driver door to wake up the data bus.
- Press UNLOCK on the OEM remote or module programming button if no OEM remote is available.
- Set the ignition to ON position.
- Set the ignition to OFF position. Disconnect power lastly.
- If LED turns solid RED, proceed to step 6; if LED flashes BLUE rapidly, proceed to step 10.
- Set ignition to OFF position.
- Repeat steps 4 to 6 eight times.
- Set ignition to ON position then OFF position.
- Wait for LED to turn solid BLUE for 2 seconds.
- Repeat steps 4 to 6 eight times.
FAQs
- Q: What should I do if the LED does not flash GREEN during module programming?
- A: Repeat step 2 by pressing UNLOCK on the OEM remote until the LED flashes GREEN.
- Q: What is the warning regarding disconnecting power during module programming?
- A: Disconnect power lastly and connect the module to a computer for extended programming. Do not press the module programming button before connecting power first.
FTI-CDP1: Notas de preparación y cobertura del vehículo
Make
DL-CH12 Chrysler
Model 300 PTS
Year 2019-23
Install
CAN
Lights
IGN
Park / Auto
Type 2 CJB/BCM Type A3 GREEN
RAP I/O Changes
Green White/Blue
NO N/A
FIRMWARE: Esta instalación requiere BLADE-AL (DL) -CH12, módulo flash y actualización del firmware del controlador antes de la instalación.
INSTALACIÓN: Las conexiones CAN utilizan el cable de extensión CAN incluido para conectarse al bloque de conexiones CAN verde (ubicado detrás de la guantera), oa los cables del BCM (conector C5, pin CANH n. ° 25, pin CANL n. ° 26).
ENCENDIDO: El encendido de tipo 2 está disponible en el BCM del vehículo (conector C5, pin # 27, rosa / blanco).
FTI-CDP1 – Notas de instalación y configuración
A CONEXIÓN REQUERIDA (cable de extensión CAN) B NO SE REQUIERE (el arnés PUEDE) C SIN CONEXIÓN D CONEXIÓN REQUERIDA (Encendido)
IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII
D LAN
2001
O
O
Z
K E R E D
st. E
IIIIIIIII
S
ID
D
KO O
rG
fo AD E
R R
E ‘T T AN NC
CE AND
WHO
O H W
WANNA
LEARN
TO
IIIIIIIII
COBFEERATTUURRAE DCEOVFEURNACGIOENES
CM7000/7200 Cut loop for A/T
CM7X00
CM-900S/900AS
CM900AS/900S Jumper
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D
O OTHER STUFF GOOD TOO
IMMOBILIZER DATA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) SECURE TAKEOVER DOOR STATUS TRUNK STATUS HOOD STATUS E-BRAKE STATUS TACH OUTPUT BRAKE STATUS GLOW PLUG STATUS PARKING LIGHTS HAZARD LIGHTS A/M CONTROL
CM -900
FTI-CDP1 – DL-CH12 – Type 2 2019-23 Chrysler 300 PTS
BLADE
PWR
pink/black
C
green pink
A
B
B
3
2
1
5 4
OBD-II connector 1
1
16
PTS Button 2
ENGINE START STOP
Headlight switch
3
AUTO
*Not required
BCM 4
RAP SHUTDOWN
D
or
C5 – Ignition
48
pink/white
brown
10
yellow
39 27 26 25
1
5
Green Junction Block
HL
Behind glove box
Códigos de error de programación de LED
El LED del módulo parpadea en ROJO durante la programación
1x – Error de CAN 2x – Código clave no aprendido 3x – Sin ENCENDIDO 4x – Sin inmovilizador, comprobar CAN / llave 5x – Error de VIN, verifique el cableado CAN 6x – Ver error 4x 7x – Error de KLON 8x – Sin ENCENDIDO, verifique la conexión
INSTALL GUIDE
Patent No. US 8,856,780 CA 2759622
Page 40 of 43
COM-BLADE-AL(DL)-CH12-EN
MODULE PROGRAMMING PROCEDURE – PTS
NOTE
I IMPORTANT: The hood must be closed.
1
Close driver door. Re-open driver door to wake up
data bus.
2
Press UNLOCK on OEM remote.
(If the vehicle is not equipped
with an OEM remote, press
on the module programming
button.)
3
Wait, LED will flash BLUE once [1x]. If LED does not flash
GREEN, repeat step 2.
10 OFF ACC ON START
ENGINE START STOP
11
12
4
OFF ACC ON START
ENGINE START STOP
Set ignition to ON position.
13
ALL IN ONE
CHRYSLER/FIAT/JEEP
Doc. No.: ##72849## 20201120
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect module from vehicle.
Connect module to computer and proceed with extended programming.
WARNING: Do not press module programming button. Connect power first. Connect module to vehicle.
5
6
OFF ACC ON START
ENGINE START STOP
Wait, if LED turns solid RED proceed to step 6. If LED flashes BLUE rapidly, proceed to step 10.
Set ignition to OFF position.
14 OFF ACC ON START
ENGINE START STOP
Set ignition to ON position.
15
Wait, LED will turn solid BLUE for 2 seconds .
7
Repeat steps 4 to 6, eight times [8x].
8
OFF ACC ON START
ENGINE START STOP
Set ignition to ON position.
16 OFF ACC ON START
ENGINE START STOP
Set ignition to OFF position.
17
Module Programming Procedure completed.
9
Wait, LED will flash BLUE rapidly.
Automotive Data Solutions Inc. © 2020
INSTALL GUIDE
Page 43 of 43
Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-CH12-EN
WARNING: READ BEFORE REMONTOETSITCAERTING THE VEHICLE
ALL IN ONE
CHRYSLER/FIAT/JEEP
Doc. No.: ##72849## 20201120
IMPORTANT
I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.
TAKE OVER PROCEDURE – PTS – TO THE VEHICLE OWNER
NOTE
2
I All vehicle doors must be closed and locked prior to remote start sequence.
TIME RESTRICTI N COMING UP !
1
Unlock vehicle door using OEM or after-market remote, or door
request switch.
3
TIME RESTRICTI N
Within 4 5 SECONDS from previous step:
Open vehicle door. Enter vehicle. Close vehicle door.
Press and release BRAKE pedal.
Take over procedure completed.
!
Failure to follow procedure will result in vehicle engine shutdown.
Automotive Data Solutions Inc. © 2020
Documents / Resources
 |
idatalink DL-CH12 Jeep Data Ddoorlock Integration [pdf] Installation Guide 2019, 2020, 2021, 2022, 2023, DL-CH12 Jeep Data Ddoorlock Integration, DL-CH12, Jeep Data Ddoorlock Integration, Data Ddoorlock Integration, Ddoorlock Integration, Integration |
