Hellas Digital Standalone Access Control Keypad
Product Usage Instructions
Light and Sound Indicators:
- Light: Red light flash every 2 sec (Slow flash), Green light flash every 0.5 sec (Fast flash)
- Sound: 1 short beep – Valid input, 3 short beeps – Invalid input, 1 long beep – Programming state, 3 long beeps – Restoring Factory Programming Password
Installations Guide:
Refer to the provided wiring diagram to correctly install the access controller.
Programming Guide:
Programming Password Default: 123456
Programming Item:
- Change Programming Password (Pro. PW)
- Add user card
- Delete all users
- Add user by input User ID
- Add PIN
- Delete user by User ID
- Delete user by card No.
- Configure Unlocking Duration
- Configure Authentication Mode
- Reset Factory Default
Basic Configuration:
- Change Programming Password: # Pro.PW # 0 new Pro.PW # new Pro.PW # # Pro.PW
- Add user card: # Pro.PW # 21 new Common PIN #
- Delete all users: # Pro.PW # 40 0000 #
How to reset to Factory Programming Password (123456):
- Turn off power and connect the OPEN and GND terminal.
- Turn on power then there is 3 long beeps with green and red light flashing alternately.
- Turn off power, and disconnect the OPEN and GND terminal.
- Turn on power again. Initializing the Programming Password is completed.
User ID Explanation:
User ID is a 4-digit number from 0001 to 9999. Perform command [40] to clear all User IDs.
Frequently Asked Questions (FAQ):
- Q: How do I add a new user card?
A: To add a new user card, follow the steps outlined in the programming guide under the “Add user card” section. - Q: What should I do if I forget the Programming Password?
A: If you forget the Programming Password, you can reset it to the Factory Default (123456) by following the steps provided in section 3.2 of the manual.
Specifications
Technical parameters:
| Operating voltage | DC 12V±10% |
| Operating current | < 100mA |
| Operating temperature | 0℃ ~ 60℃ |
| Storage | 1000users |
| Card type | EM(standard) / Mifare(optional) |
| Reading distance | 1－5CM |
Factory Default:
| Authentication Mode | Card or Password(PIN) |
| Unlocking Duration | 5 S |
| Common PIN | None |
Light and Sound indicates:
- Light: red and green
Light Description Indicates Red light flash every 2 sec(Slow flash) Standby state Green light flash every 0.5sec(Fast flash) Pending further operation Red light is always ON Programming state Green light is always ON Unlocking state Red and green light flash alternately Restoring Factory Programming Password - Sound: beep
Sound Description Indicates 1 short beep Valid input 3 short beeps Invalid input 1 long beep Programming state 3 long beeps Restoring Factory Programming Password
Installations Guide
JP1:
| NO | Mark | Color | Function |
| 1 | +12V | Red | Power+ |
| 2 | GND | Black | Power- |
| 3 | PUSH | BLUE | Low level output |
| 4 | OPEN | Yellow | Door Release |
| 5 | BEL+ | Grey | High level Input |
| 6 | BEL- | White | Voltage output |
JP2:
| NO | Mark | Color | Function | Remark |
| 1 | NC | Brown | Relay NC output | |
| 2 | COM | Blue | Relay Com output | |
| 3 | NO | Purple | Relay NO output |
Wiring diagram
Programming Guide
Programming Guide: (Programming Password Default: 123456)
| Programming Item | Press key and swipe card operations | Remark | |
| Basic Function | Change Programming Password (Pro. PW) | # Pro.PW # 0 new Pro.PW # new Pro.PW # | If Pro PW lost, perform 3.2 to reset to Factory Default (123456) |
| Add user card | # Pro.PW # 1 swipe cards # | If add series cards, swipe cards continuously | |
| Configure Common PIN | # Pro.PW # 21 new Common PIN # | Common PIN is only one, Unlocking method: Enter Common PIN then press [#] | |
| Delete all users | # Pro.PW # 40 0000 # | Delete all cards and PIN except Common PIN | |
| Delete user by swiping card | # Pro.PW # 41 swipe cards # | If delete series cards, swipe cards continuously | |
| Expand Function | Add user by input User ID | # Pro.PW # 224-digit User ID swipe card # | Adduser card or PIN byuser’s ID. User ID must be 4 digits and cannot be reused (3 beeps means reused and need to enter a new). If add senies users repeat the operation. More about User ID see 3.3 |
| Add PIN | # Pro.PW # 23 4-digit User ID new PIN # | ||
| Delete user by User ID | # Pro.PW # 424-digit User ID # | ||
| Delete user by card No. | # Pro.PW #43 card No.# | Card No. is 10-digit or 8- digit, device auto-identify | |
| Configure Unlocking Duration | # Pro.PW # 5 XX # | XX is 2-digit (00 ~99). If xx is 00, Unlocking Durationis 0.2s | |
| Configure Authentication Mode | # Pro.PW # 6 XX # | XX can be 01(only Card)/02(Card or PIN)/03(Card & PIN) | |
| Reset Factory Default | # Pro.PW # 8 99 # | Except Programming Password and Manager Card |
Remark: All password can be 3~6 digits
How to reset to Factory Programming Password (123456)
- Step 1: Turn off power and connect OPEN and GND terminal. Turn on power then there is 3 long beeps with green and red light flashing alternately.
- Step 2: Turn off power, disconnect OPEN and GND terminal. Turn on power again. Initializing Programming Password is completed.
Use ID explanation
User ID is 4-digit number from0001 to 9999. There is no User ID for the users added by command [1]. Perform command [40] to clear all User ID.
Other extensions
- How to change PIN
Swipe card or press PIN to unlock within 5s press [#] for 3 suntil the green light flash fast, then press [new PIN#new PIN#], the new PIN is changed successfully with a long beep. - Authentication Mode for Card& PIN function
- Step 1: When Authentication Mode is [Card or PIN] (factory default), according to step 3.4 to configure the PIN of the card.
- Step 2: Press [#Programming Password#603#] to configure Authentication Mode to be [Card & PIN].
- Step 3: Swipe user’s card with green light fast flash then input [PIN#]with green light normally ON, the door opened successfully.
- Door open function description:
When the credit card or password is normally opened, press the 7, 9 digit key to keep the door open. When the door is always open, only once the credit card, password, or the door button is opened again, the exit is always open.
Documents / Resources
 |
Hellas DIgital Standalone Access Control Keypad [pdf] Instructions Standalone Access Control Keypad, Standalone Access Control Keypad, Access Control Keypad, Control Keypad, Keypad |
