ASUS GU603Z Computer and Electronics Store
Product Specifications
- Model: ASUS ROG Zephyrus M16 (GU603Z) series
- Manufacturer: ASUSTeK COMPUTER INC. (ASUS)
- Display Panel: 16-inch LCD Panel
- Ports: HDMI output port, LAN port, USB 3.2 Gen 2 port
- Features: Array microphones, Camera, Display panel, Status indicators, Audio speakers, Keyboard, Touchpad
Product Usage Instructions
Service Overview
- The ASUS ROG Zephyrus M16 (GU603Z) series is designed for high-performance gaming and productivity tasks. The service guide provides detailed information on the components and repair procedures.
Components Overview
- The laptop features top and bottom views with components like microphones, camera, display panel, status indicators, audio speakers, keyboard, touchpad, air vents, power button, HDMI output port, LAN port, and USB ports.
Disassembly Steps
- Ensure appropriate tools are available.
- Follow the disassembly steps outlined in the manual to access internal components.
- Handle components with care to avoid damage during disassembly.
FAQ
- Q: Can I upgrade the RAM on the ASUS ROG Zephyrus M16?
- A: Yes, the laptop supports RAM upgrades. Refer to the service guide for instructions on accessing and upgrading the RAM.
- Q: How can I clean the air vents of the laptop?
- A: To clean the air vents, use compressed air to blow out any dust or debris that may have accumulated. Ensure the laptop is powered off before cleaning.
“`
ASUS ROG Zephyrus M16 (GU603Z) series Service Guide
INFORMATION
COPYRIGHT INFORMATION
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Copyright © 2024 ASUSTeK COMPUTER INC. All Rights Reserved.
LIMITATION OF LIABILITY
Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product.
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement.
This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
Disclaimer ASUS is not responsible for direct, indirect, intentional or unintentional damages resulting from improper installation and operation. Safety precautions · Keep liquids or moisture away from your Notebook PC before installing or removing any components. · Ensure to place your Notebook PC on a stable surface before installing or removing any components. · Detach the clip or flap before removing the signal cables to prevent damage. · Disconnect the power plug by pulling the plug evenly to avoid damage. Ensure to connect the signal cables in the correct orientation. · Disconnect all power cables and remove the battery pack (if applicable) before cleaning your Notebook PC with liquid detergent to avoid risk of electric shock. · Disconnect all power cables and remove the battery pack (if applicable) before installing or removing any components. Ensure to read and follow the instructions in the manual. · Before handling components, use a grounded wrist strap or touch a safely grounded object to avoid damaging them due to static electricity. · Keep liquids or moisture away from your Notebook PC to avoid short circuits. · Hold components by the edges to avoid touching the ICs. · Ensure to properly install all the components before connecting the AC power. · Do not use power adapters or batteries from other devices to reduce the risk of injury to persons due to fire or explosion. Use only certified power adapters or batteries supplied by
the manufacturer or authorized retailers. · Ensure to install the correct screw models on your Notebook PC to prevent damage.
Service Overview
· Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs. · To provide the best service, we have provided the below information for technicians from distributors and resellers to perform the complete device
disassembly and assembly. Before performing the procedures, please be sure to read through the overview in this service guide for component overview to avoid any unwarranted damages to the device hardware. · The following contents include all part numbers mentioned in the service guide are used for reference only, if you need the exact part number for ordering, please refer to the OrderBook. · Due to sales policy difference, the components might have different specifications on the same series product, please refer to E-manual by model. Due to sales policy difference, the components may have different specifications on the same model. If you have any operational issues, please contact the service hotline.
5 Back
Top View
Right View
Left View
ASUS ROG Zephyrus M16 (GU603Z) series Overview
Array microphones Camera indicator Camera Display panel Status indicators Audio speakers Capital lock indicator Power button Keyboard Touchpad
Cover View Bottom View
Microphone Air vents Audio speakers Compartment cover
USB 3.2 Gen 1 port MicroSD card slot Air vents Kensington® Security slot
Air vents Power (DC) input port HDMI output port LAN port USB 3.2 Gen 2 port
Thunderbolt 4 port with Power Delivery USB 3.2 Gen 2 Type-C® /DisplayPort/Power Delivery combo port Headphone/Headset/Microphone jack
6 Back
Components Top View
LCD COVER
LCD Panel (16″)
LCD BEZEL
KEYBOARD
BASE CASE
MAIN BOARD
THERMAL
FAN
MODULE
MODULE
MODULE
HALL SENOR BD
POWER BD
DDR
SSD
BATTERY
WIFI CARD
TOUCHPAD MODULE
GPU CPU CAMERA
BATTERY CABLE
BATTERY RIB RUBBER
POWER KEY RUBBER
WIFI ANTENNA
A1
A2
HINGE L/R
R
L
SSD THERMAL PAD
HALL SENSOR FFC (4P 0.5 L89mm)
TP FFC (8P 0.5 L76mm)
MIC RUBBER
HINGE CAP L/R
HINGE DECO RUBBER L/R
WOOFER SPEAKER TWEETER SPEAKER
R
L
R
L
MB DIMM ABSORBER DIMM CONN ABSORBER
TWEETER TAPE TP SPONGE
EDP CABLE
MB WIFI MODULE MYLAR
FP PW FFC (4P 0.5 L110mm)
MIC FPC
SCREW RUBBER
SSD ABSORBER
TP HOLDER MYLAR
7 Back
LCD COVER MODULE
LCD Panel
Components Bottom View
POWER BD
CABLE SPONGE
LCD ADHESIVE
LCD BEZEL
LCD BEZEL ADHESIVE TOP
BASE CASE
LCD BEZEL ADHESIVE L/R
LCD BEZEL ADHESIVE KEYBOARD MODULE
MAIN BOARD
HALL SENSOR PCB ADH
HALLSENSOR BD LCD CU FOIL GRAPHITE CABLE TAPE
THERMAL MODULE ASSY THERMAL COVER MYLAR 1 (26*2*0.3mm)
8
THERMAL COVER MYLAR 2 (31*2*0.3mm)
Back
Repair Overview
This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure.
Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook.
1. Be sure that the notebook is powered down. 2. Before disassembling any part, please disconnect all power source. ex: AC plug/Battery connector/Power protect screw etc.
3. Remove all rings, watches and any other metal objects from your hands.
9. Screw Appearance Criteria: If the screws have the following damaged appearance, please do not use. a. Shape deformed. b. Damaged head unable to drive in or the stripped screw. c. Damaged unable to securely tighten. d. Paint scratched off. e. Rusty
4. Always wear a ground strap on your hand to protect the notebook from static discharge. 5. Please refer to “ANSI ESD S20.20” about ESD protection measure. 6. Put the disassembled parts in the functional PE BAG to avoid any damages of the
A/B/C/D part.
10. The following chapter includes all part numbers mentioned in service guide are used for reference only, actual part name depends on different SKU, if you need the exact part number for ordering, please refer to the Orderbook.
7. The maintenance environment temperature is 20-30 and humidity is 40% – 70%. 8. To avoid scratching on the surface of machine; please use anti-static and soft materials
to put on desk in repair environment as below photo.
11. Due to sales policy difference, the components may have different specifications on the same model. Please note that all pictures and components shown on Service Guide are for disassembly/assembly description purpose only, so please refer to the actual product for disassemble/assemble.
9 Back
Appropriate Tools
Please prepare and select the appropriate tools to disassemble/assemble for the ASUS ROG Zephyrus M16 (GU603Z) series notebook.
Screwdriver Please accord to different screw specification to choose different screwdriver and head.
Alcohol 95%
Glove
#1
Plastic Blade
Plastic Tweezers Use a pair of tweezers to remove/insert/tidy cables.
Thermal Pad PTM7958
PLASTIC CARD T=0.35mm
Dust-free Cloth
Thickness Gauge Thickness compass specification 0.05mm-1.5mm. Use it to measure the gap.
FCR-AS Thermal Grease
PLASTIC PICK T=0.5mm
Magnetism Board
Suggest local buy magnetism board to place screw, avoid mix different type screw to cause assembly damage.
NB LCD MYLAR *4pcs Use it to align panel position. LCD MYLAR can be reused 5 to 10 times, please stick it on the plastic bag save after used, and repeatedly use until lose stickiness.
1 Bac0k
Appropriate Tools
Please prepare and select the appropriate tools to disassemble/assemble for the ASUS ROG Zephyrus M16 (GU603Z) series notebook.
Tooling Type For Liquid metal use
For Clean use
Item
Part Name
Silicone scraping pen
Conductonaut 1g (Liquid Metal)
Intel ADL-P H45 steel plate Stainless steel plate (60mm*20mm*0.2t) Dust-free cotton swab//class 100 (100pcs) 95% alcohol Dust-free cloth
Warning! When the tool is with Liquid Metal residue, please clean tools with dust free cloth and 95% alcohol.
Memo
Please store it in the environment of 10 ~ 40 . Please keep cover tightly closed until ready for next time use. Shipping category : Dangerous Goods.
11 Back
Disassembly
Disassembly Notice
Step 1 : Remove rubbers *3pcs. Step 2 : Remove screws *12pcs. Step 3 : Use plastic blade to pry the bottom case.
1
(*3 PCS)
2
BOTTOM CASE
Screws
QTY
Spec
4 M2*11L (4.5,0.8) (K) #1
3 M2*8L(4.5,0.8) (K)#1 3 M2*8L(4.5,0.8) (K)#1 2 M2*11.5L (4.5,0.8) (K) #1 1 Retention Screw
Torque (kgf-cm) 2.0±0.2 2.0±0.2 2.8±0.2 2.0±0.2 2.0±0.2
Start
The screw is unable to remove
To avoid the bottom case hook,
Please follow above arrow direction with using
from bottom case, so please always
don’t insert plastic blade in each
plastic blade to pry bottom case in each blue circle
loosen it last, and lock it at first.
red circle.
location.(To avoid the bottom case hook, please prying at each blue circle location.)
12
Back
BATTERY
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage.
Step 1 : Disconnect the battery connector. Step 2 : Remove screws *4pcs.
Screws
QTY
Spec
Torque(kgf-cm)
Step 3 : Remove BATTERY.
2 M2*8.0L (4,0.8) (K) #1
2.0±0.2
Step 4 : Disconnect battery cable.
2 M2*4.5L (4.5,0.8) (K) #1
2.0±0.2
Assembly Notice
For BATTERY RIB RUBBER assembly, please follow below location to paste. * The BATTERY RIB Rubber need to be attached on the rib.
1 Disconnect
BATTERY RIB RUBBER
3 Remove 4 Disconnect
To prevent getting a short circuit or an electric shock accident, please follow the below steps to connect the battery connector.
Step 1 : Use the non-conductive pry tool to connect the black cable side first, then connect the red cable side. Step 2 : Use the non-conductive pry tool to push the iron sheet.
1
2
2
13 Back
SSD
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Remove the Thermal PAD. Step 2 : Remove the screw *1pc. Step 3 : Remove the SSD. Step 4 : Remove BOT THERMAL PAD. Step 5 : Tear off SSD ABSORBER from SSD.
Screws QTY 1
1 Remove
Spec M2*4.5L(4.5,0.8) (K)#1
Torque(kgf-cm) 2.0±0.2
Assembly Notice
When installing the SSD, please keep the SSD less then 15 degrees with motherboard, and then insert the SSD.
2 Unscrew >15°
3 Remove
<15° 4 Remove
5 Remove
SSD front and back
14 Back
DDR
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Tear off SODIMM MYLAR. Step 2 : Unlock and remove the DDR. Step 3 : Tear off SODIMM ABSORBER from DDR.
1 Tear off
2 Unlock and Remove
Assembly Notice
Please make sure to paste ABSORBER on the back side of DDR, before assembling the DDR.
Align
3 Tear off
Turn over and tear off
15 Back
WIFI CARD
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Tear off the TAPE and MYLAR. Step 2 : Disconnect RF cable *2pcs. Step 3 : Remove the screw *1pc. Step 4 : Remove the WLAN CARD.
Screws QTY 1
Spec M2*4.5L(4.5,0.8) (K)#1
Torque(kgf-cm) 2.0±0.2
1 Tear off
Assembly Notice
Please according to below image to assemble RF cable.
AUX MAIN
2 Disconnect
3 Unscrew
After the WIFI card is assembled, please paste the CABLE TAPE and Mylar according to the following positions.
4 Remove
CABLE TAPE
MB WIFI MODULE MYLAR
16 Back
HALL SENSOR BD
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Disconnect the HALL SENSOR FFC connector. Step 2 : Remove HALL SENSOR FFC. Step 3 : Remove HALL SENSOR BD.
1 Disconnect
Assembly Notice
If FFC is damage during disassembly, please replace new one. Here are some samples of FFC damage:
2 Remove 3 Remove
For HALL SENSOR BD assembly, please paste HALLSENSOR PCB ADH (1pcs) as below.
17 Back
WOOFER SPEAKER
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Disconnect the SPEAKER connector. Step 2 : Remove the SPEAKER.
1 Disconnect
Assembly Notice
For Woofer Speaker assembly, please follow the mark below to tidy up cable.
2 Remove
18 Back
THERMAL MODULE
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Disconnect EDP cable (Blue area) and release tapes and EDP cable. Step 2 : Please follow the reverse screws numbers to remove and release screws *7pcs. Step 3 : Remove the THERMAL MODULE.
Screws QTY 4 3
Spec M2*4.5L (4.5,0.8) (K) #1
Retention screw
Torque (kgf-cm) 2.0±0.2 2.0±0.2
Recommend that the force point is at green block, and pull up thermal module to take it out. Do not pull up at red block and also notice the thermal pipe should not have deformation.
1 Disconnect and Release
2 Unscrew
3 Remove
7 14 5
32 6
Assembly Notice
Step-1 THERMAL MODULE Location:[VRAM/CHOKE/MOS] Material: FCR-AS Grease
MB Location:[GPU] Material: TH PAD PTM7958
Step-2 Please refer Repair Notice SOP for Liquid metal rework when reassemble thermal module before.
MB Location:[CPU]
Step-3 Please follow the screws numbers to lock screws *8pcs.
IMPORTANT! Thermal paste, thermal pads, liquid metal, or other thermal interface materials must be thoroughly removed and replaced if this component is removed. Ensure that replacement materials are available before proceeding, or contact an authorized service center for assistance.
WARNING! The heat sink contains liquid metal and should
only be removed by authorized service personnel. Significant
damage may occur to motherboard components if the heat
sink is improperly removed.
19
Back
FAN
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Disconnect connectors *2pcs. (Yellow mark) Step 2 : Remove screws *4pcs. (Green mark) Step 3 : Remove the FAN *2pcs.
Screws QTY 4
Spec M2*4.5L (4.5,0.8) (K) #1
Torque (kgf-cm) 2.0±0.2
3 Remove 2
1
Assembly Notice Please use the correct technique to take fans off to avoid getting out of shape.
Please follow below location to paste CABLE TAPE. (Green mark)
20 Back
MAIN BOARD
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Disconnect connectors. (Yellow mark) Step 2 : Remove screws *2pcs. (Green) Step 3 : Remove the MAIN BOARD.
Screws QTY 2
Spec
Torque (kgf-cm)
M2*4.5L (4.5,0.8) (K) #1
2.0±0.2
1 Disconnect 2 Unscrew
Please refer Repair Notice SOP to rework Liquid metal.
21 Back
Mainboard connector placement
GPU FAN Antenna
MAIN BOARD
FP PW FFC
Supports using JIG BOARD to refresh F1 BIOS
HALL SENSOR FFC
BL FPC TP FFC KB Membrane Battery
CPU FAN
EDP CABLE WOOFER SPEAKER TWEETER SPEAKER
22 Back
MAIN BOARD
Materials on mainboard
GU603ZEB: GU603ZEB RUBBER DUMMY VRAM
GU603ZX :
GU603ZX GN20-E8 GPU ABSORBER GU603ZW :
GU603ZW GN20-E6 GPU ABSORBER GU603ZM :
GX703HS GN20-E3 GPU ABSORBOR
GA503QS TC BOSS WASHER L ASSY
GU603ZX CPU BRACKET ASSY
GU603ZX CPU TOP ABSORBER
X455LDB SMT GASKET
TP201SA SMT GASKET 4*4*3
X455LDB SMT GASKET
GU603ZX CPU MYLAR
GU603ZX MB TOP TAPE 1 GU603ZX MB TOP GASKET 1
GA503QS TC BOSS WASHER R ASSY
GU603ZX MB TOP ABSORBER U1
GA503QS MB TOP RUBBER2
GA503QS GN20 GPU BRACKET ASSY
GA503QS GPU ABSORBER
GU603ZEB: GU603ZEB RUBBER DUMMY VRAM
GA503QS BATTERY SUPPORT WASHER ASSY
GU603ZX CPU BOT ABSORBER 1
GA503QS BATTERY SUPPORT WASHER ASSY
GA503QS MB TOP RUBBER1
GU603ZX RUBBER GPU BKT
GX550LXS MB DIMM ABSORBER
GA503QS MB TOP RUBBER1
GU603ZX MB TOP SPONGE 1
GU603HR MB EC MYLAR
MB TP MYLAR 23 Back
POWER BD
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Remove screws *2pcs and remove POWER BD with FP PW FFC. Step 2 : Disconnect connector and remove FP PW FFC from POWER BD. Step 3 : Remove POWER KEY from top case.
Screws QTY 2
Spec
Torque (kgf-cm)
M2*3L (K) B-ZN #1 NY
2.0±0.2
1 Unscrew
2 Disconnect
3 Remove
Assembly Notice
If FFC is damage during disassembly, please replace new one. Here are some samples of FFC damage:
24 Back
TWEETER SPEAKER
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Release TWEETER TAPE *5pcs. (Red mark) Step 2 : Use plastic blade to separate tweeter speaker from TOP CASE. (Green mark)
Assembly Notice
When TWEETER SPEAKER assembly, please follow below mark to tidy up cable and paste TWEETER TAPE *5pcs.
2 Separate
25 Back
TOUCHPAD MODULE
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Disconnect and remove the FFC. Step 2 : Flip up the KB FPC. Step 3 : Remove screws *3pcs. Step 4 : Remove TOUCHPAD module.
Screws QTY 3
Spec
Torque (kgf-cm)
M2*2.5L (4.5,0.5) (K) #1
2.0±0.2
2 Flip up
Assembly Notice
After TOUCHPAD assemble, please follow below location to paste the TP Sponge.
1 Disconnect
3 Unscrew 4 Remove
TP Sponge
26 Back
KEYBOARD MODULE
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Remove hinge’s screws *6pcs. Step 2 : Flip up and remove KB module.
Screws QTY 6
Spec
Torque (kgf-cm)
M2*4.5L (4.5,0.8) (K) #1
2.0±0.2
1 Unscrew
2 Flip up and remove
Assembly Notice
After the Keyboard module assembly, please follow below location to paste the THERMAL COVER MYLAR.(*2pcs)
THERMAL COVER MYLAR 1 (26*2*0.3mm)
THERMAL COVER MYLAR 2 (31*2*0.3mm)
27 Back
LCD BEZEL
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Remove LCD BEZEL.
1
Step 1-1~1-3, Start from the middle area of each side of bezel, Using the forefinger to hold the outer edge firmly and the thumb flipping the bezel inner edge outward to release the hooks as indicated in the diagram shown. (It can be helpful, if holding the bezel outer edge firmly with forefinger.)
1-3
Step 1-1~1-3
Thumb flipping the inner edge outward.
1-1
1-2
Step 1-4 Due to some tapes behind the lower edge of bezel, please using plastic blade to teardown the bezel. Please follow the direction shown in the red arrow, to move plastic blade from left to right and peel the bezel away slowly. While peeling, please move the blade in the parallel direction to the panel and pressing the black Mylar downward (As circled in green) to ensure the black Mylar and the tape behind the bezel are well separated. Please move blade slowly to separate the bezel away, and must press the black Mylar downward with panel parallel direction..
Panel’s black Mylar
1-4
Assembly Notice
When reuse the LCD BEZEL: Please paste new LCD BEZEL ADHESIVE before assembly BEZEL. (New LCD BEZEL already contains LCD BEZEL ADHESIVE *1pcs, LCD BEZEL ADHESIVE TOP*1 pcs, LCD BEZEL ADHESIVE L/R*2pcs.)
LCD BEZEL ADHESIVE TOP LCD BEZEL ADHESIVE L/R
LCD BEZEL ADHESIVE
28 Back
LCD PANEL
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Pull out LCD adhesive *2pcs. Step 2 : Flip up the panel and disconnect the EPD cable. Step 3 : Remove screws *6pcs then remove HINGE module R & L. Step 4 : Remove screws *4pcs and remove caps and deco rubbers from HINGE.
Screws QTY 6 4
Spec M2.5*2.3L(7.5,0.6)(K) #1 M1.4*2.5L(3.4,0.5) (K)#0
Torque (kgf-cm) 2.3±0.2 kgf-cm 1.3±0.2 kgf-cm
1
Please pull the adhesive up about 30 degree slowly, and don’t pull out the tape in
vertical direction!
2 Flip up the panel, and disconnect the MIC cable and EDP cable.
Flip up .
Disconnect
3
30
4
29 Back
LCD PANEL
Assembly Notice Please be sure to pull out adapter and disconnect the battery.
A When reuse the LCD PANEL or BEZEL: Please use the fingertip to clean the residual glue on PANEL or BEZEL.
B Before assembly the NEW LCD PANEL : Please make sure paste GRAPHITE and CU FOIL at panel back side.
Step-1 Please confirm the position to be paste according to different panel.(Green line).
With Position line panel
Without Position line panel
Step-2 Paste the GRAPHITE.
Step-3 Paste the CU Foil. (on the GRAPHITE)
30 Back
LCD PANEL
Assembly Notice Please be sure to pull out adapter and disconnect the battery.
C When assembly the LCD PANEL: (The following is an operation example)
Step 1~2 : Paste NB LCD MYLAR *6pcs on LCD COVER. (Positions are as below)
Step-1 Upper Left Corner : Mylar *3pcs Overlap LCD MYLAR *2pcs
Step-2 Upper Right Corner : Mylar *3pcs Overlap LCD MYLAR *2pcs
LCD MYLAR *1pcs
LCD MYLAR *1pcs
Step 3 : Remove release paper of LCD Adhesive *2pcs. Step 4 : Assembly and align the LCD to the upper side of the LCD Cover. Step 5 : Remove Mylar *6pcs and complete the Panel assembly.
Step-3 Remove
Step-4 Align
Step-5 Pull out Mylar *6pcs.
Release paper
Please stick LCD MYLAR on the plastic bag save after used, and repeatedly use until lose stickiness.
31 Back
LCD COVER MODULE
Disassembly Notice Please be sure to pull out adapter and disconnect the battery.
Step 1 : Release GASKET and disconnect MIC FPC connector *2pcs. Step 2 : Remove MIC FPC and EDP CABLE. Step 3 : Remove CAMERA. Step 4 : Remove MIC RUBBER *2pcs.
1 Release and disconnect
Assembly Notice
After the camera module is assembled, please stick the camera module tape according to the following positions, and then connect the MIC FPC.
Camera module tape
2 Remove
3 Remove
4 Remove
32 Back
LCD COVER
Assembly Notice Please be sure to pull out adapter and disconnect the battery.
A Please follow the green mark to tidy up MIC FPC and EDP CABLE.
CABLE SPONGE
LCD COVER
Assembly Notice Please be sure to pull out adapter and disconnect the battery.
B Please follow the green mark to tidy up ANTENNA CABLE.
ANTENNA A1
ANTENNA A2
C When reuse the LCD COVER: Please paste new PANEL ADHESIVE *2pcs. (New LCD COVER already contains PANEL ADHESIVE *2pcs)
LCD ADHESIVE
CABLE SPONGE
Documents / Resources
 |
ASUS GU603Z Computer and Electronics Store [pdf] User Guide GU603Z Computer and Electronics Store, GU603Z, Computer and Electronics Store, Electronics Store, Store |