LASER TECH 0144878 TRUPULSE 200L User Guide
LTI Technical Support
Toll Free: 1.877.696.2584 Phone: 1.303.649.1000
Email: service@lasertech.com
Web: www.lasertech.com
Tru Pulse® 200L Display Icons
TruPulse® Values & Key Code
1-Shot Distance 2-Shot Missing Line
2-Shot Height 3-Shot Height
Measured by TruPulse
Calculated by TruPulse
Change Units of Measurement
[1] Press-and-hold (
), then press .[2] Press to scroll through (
) and press to choose.[3] Press to scroll through ( ) and press to choose
Change Targeting Mode
[1] For Standard Mode, press-and-hold ( ) will show as the default mode.[2] Press repeatedly to scroll through the mode options:
[3] Stop at the desired mode and press to accept it. The icon for the selected mode will show (no icon for Standard Mode)
[4] Repeat steps to change target mode again
Measure Distance
In mode, the 200L will automatically measure and then calculate and . Measurements are from the 
tripod mount (center) of the laser to target.
[1] Press-and-hold ( ).
[2] Aim at target where you have a clear line of sight then press-and-hold .
The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed.
[3] Press to scroll through ( ) values.
Helpful Tips
The solution is critical for mapping in objects.
The solution can be used to measure height or clearance, as in the image to the left – just add the height of the laser at your eye level to the measurement.
Measure Height in 3-Shots
[1] Press until ( ) displays and (
) flashes.[2] Aim where you have a clear line of sight to the target and press-and-hold .
The laser indicator will be displayed. When the measurement is acquired (- ) will be displayed.
[3] ( ) and the ( ) flashes. Aim to bottom, press-and-hold (- )
[4] ( ) Aim to top, press-and-hold , ( )( ).
FIRE
FIRE
FIRE
Helpful Tip
This routine is ideal for flat, vertical objects that do not lean. To shoot through brush, use the filter mode, foliage filter and a reflector
Measure Height in 2-Shots
[1] Press until ( ), aim at bottom of target then press-and-hold .The laser indicator will be displayed. When the measurement is acquired (- ) will be displayed. Note this value for the Vertical Distance (VDb) measurement.
[2] Aim at the top of the target then press-and-hold .
[3] The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed. Note this value for the Vertical Distance top (VDt) value. Add the two values to calculate the height VDb + VDt = Height.
Helpful Tip
The 2-shot height works well on leaning objects and requires a clear line of sight for both shots.
Measure 2D Vertical Missing Line
[1] Press until ( ) displays and ( ) flashes.[2] Aim at the 1st target, press-and-hold .
– The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed.
[3] ( ) displays and ( ) flashes. Aim at 2nd target, press-and-hold .
– The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed.
[4] ( ), keep pressing to scroll through ( ) from shot 1 to shot 2.
Helpful Tip
Position yourself where shot 1 and 2 are made looking in the same directions and vertical plane with a clear line of site to both targets. The exception is the solution
will always be accurate no matter which direction shot 1 and 2 are taken.
Read More About This Manual & Download PDF:
Documents / Resources
 |
LASER TECH 0144878 TRUPULSE 200L [pdf] User Guide 0144878 TRUPULSE 200L, 0144878, TRUPULSE 200L, 200L |
