Laser Tech - Laser Measurement Innovation
User Guide for LASER TECH models including: 0144878 TRUPULSE 200L, 0144878, TRUPULSE 200L, 200L
TruPulse 200L Laser Rangefinder | Laser Tech
In mode, the 200L will automatically measure and then calculate and . Measurements are from the 1/4-20 tripod mount
File Info : application/pdf, 10 Pages, 988.35KB
DocumentDocument© LTI 2020 Rev 02 09/29/20 TruPulse® 200l Quick reference field Guide LTI Part #0144878 TruPulse® 200L Fire Button FIRE Up Button Down Button LTI Technical Support Toll Free: 1.877.696.2584 Phone: 1.303.649.1000 Email: service@lasertech.com Web: www.lasertech.com LTI Hours of Operation Monday through Friday 8:00 am to 5:00 pm (MST) (Excluding Holidays) LTI Corporate Headquarters 6912 South Quentin Street, Suite A Centennial, CO 80112 USA LTI YouTube® Channel www.youtube.com/lasertechpro for TruPulse® Training Videos TruPulse® 200L Measurement Modes Display Icons Inclination Slope Distance Horizontal Distance Vertical Distance Feet Meters Yards Degrees Percent Missing Line Height Target Modes Closest Farthest Continuous Filter Laser Indicator Battery Life Indicator TruPulse® 200L Measured by TruPulse Values & Key Code Calculated by TruPulse 1-Shot Distance 2-Shot Missing Line = Horizontal Distance (HD) = Slope Distance (SD) = Vertical Distance (VD) = Height (HT) = Inclination (INC) = Missing Line 2-Shot Height 3-Shot Height FIRE = Fire Button = Up Button = Down Button ( ) = In-scope Top ( ) = In-scope Bottom Change Units of Measurement [1] Press-and-hold ( ), then press FIRE . [2] Press to scroll through (Y [Yards] M [Meters] F [Feet] ) and press FIRE to choose. [3] Press to scroll through (° [Degrees] % [Percent] ) and press FIRE to choose. Change Targeting Mode [1] For Standard Mode, press-and-hold ( ) will show as the default mode. [2] Press repeatedly to scroll through the mode options: ( ) Filter (note: the optional ( foliage filter must be used with this mode) ( ) Farthest ( ) Closest ) Continuous [3] Stop at the desired mode and press FIRE to accept it. The icon for the selected mode will show (no icon for Standard Mode) [4] Repeat steps to change target mode again. Measure Distance In mode, the 200L will automatically measure and then calculate and . Measurements are from the 1/4-20 tripod mount (center) of the laser to target. [1] Press-and-hold FIRE ( ). [2] Aim at target where you have a clear line of sight then press-and-hold FIRE . The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed. [3] Press to scroll through ( ) values. Helpful Tips The solution is critical for mapping in objects. The solution can be used to measure height or clearance, as in the image to the left - just add the height of the laser at your eye level to the measurement. Measure Height in 3-Shots This routine is ideal for flat, vertical objects that do not lean. To shoot through brush, use the filter mode, foliage filter and a reflector. [1] Press until ( ) displays and ( ) flashes. [2] Aim where you have a clear line of sight to the target and press-and-hold . FIRE The laser indicator will be displayed. When the measurement is acquired (- ) will be displayed. [3] ( ) and the ( ) flashes. Aim to bottom, press-and-hold FIRE (- ) [4] ( ) Aim to top, press-and-hold FIRE , ( )( ). Helpful Tip In the routine, the laser does not actually fire when taking the two measurements, so you do not need a clear line of sight to the top or bottom of your target. The sequence of the shots does not matter. Measure Height in 2-Shots [1] Press until ( ), aim at bottom of target then press-and-hold FIRE . The laser indicator will be displayed. When the measurement is acquired (- ) will be displayed. Note this value for the Vertical Distance (VDb) measurement. [2] Aim at the top of the target then press-and-hold FIRE . [3] The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed. Note this value for the Vertical Distance top (VDt) value. Add the two values to calculate the height VDb + VDt = Height. Helpful Tip The 2-shot height works well on leaning objects and requires a clear line of sight for both shots. Measure 2D Vertical Missing Line [1] Press until ( ) displays and ( ) flashes. [2] Aim at the 1st target, press-and-hold FIRE . - The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed. [3] ( ) displays and ( ) flashes. Aim at 2nd target, press-and-hold FIRE . - The laser indicator will be displayed. When the measurement is acquired ( ) will be displayed. [4] ( ), keep pressing to scroll through ( ) from shot 1 to shot 2. Helpful Tip Position yourself where shot 1 and 2 are made looking in the same directions and vertical plane with a clear line of site to both targets. The exception is the solution will always be accurate no matter which direction shot 1 and 2 are taken. www.lasertech.com 1.303.649.1000 info@lasertech.com