ON-Q360AG Air Lancer
“
Specifications
- Frequency range: 2.4 GHz and 5 GHz
- Antenna characteristics: LANCOM AirLancer
ON-Q360ag - Radiation characteristics: See radiation
patterns below
Product Usage Instructions
Mounting the Antenna
Wall Mounting: Attach the antenna bracket to
the wall using the enclosed bolts. Drill holes if necessary and
insert dowels.
Pole Mounting: Use screw clamps to attach the
antenna bracket directly to the pole.
Attaching Antenna Arm to Antenna: Ensure a
close fit between the arm and antenna. Use the pin on the arm and
matching recess on the antenna. Secure with the locking screw.
Mounting Upside Down: For outdoor mounting with
cables exiting upwards, seal with the insulation disk before
attaching it to the arm.
Attaching Antenna to Bracket: Place the
antenna-arm joint socket onto the joint head of the bracket.
Tighten using the wing screw or hexagon socket screw provided.
Suspended Ceiling Mounting: Make a 3-cm
diameter hole in the ceiling, stick the insulation disk to the
antenna, insert cables, pass through the hole, and tighten using
the locking screw.
Important Information
Configuring Antenna Gain: To comply with safety
standards, configure the accurate antenna gain value in your Wi-Fi
router or access point settings.
Disposal: Dispose of electronic waste properly
according to regulations in your country.
Handling Antenna Cables: Avoid creasing or
bending the sensitive RF cables during installation to prevent
performance loss. Do not coil the cable tightly.
Radiation Patterns
FAQ
Q: Can I mount the antenna without using the provided
bolts?
A: It is recommended to use the enclosed bolts for secure
mounting to ensure stability and proper function of the
antenna.
Q: How do I know if I have configured the antenna gain value
correctly?
A: Refer to the user manual of your Wi-Fi router or access point
for guidance on configuring the antenna gain value to meet safety
standards.
“`
Mounting Instructions
LANCOM AirLancer ON-Q360ag
Mounting Instructions LANCOM AirLancer ON-Q360ag Attaching the antenna bracket by wall mounting In the case of wall mounting, attach the antenna bracket to the wall with the enclosed bolts. You may need to drill the holes first and insert dowels.
Attaching the antenna bracket by pole mounting In the case of pole mounting, use screw clamps to attach the antenna bracket directly to the pole.
Attaching the antenna arm to the antenna When attaching the antenna arm to the antenna, please ensure that there is a close fit between them. Make use of the pin on the antenna arm and the matching recess in the antenna. Finally, use the locking screw to secure the antenna arm to the antenna.
Important Mounting the antenna upside down If the antenna will be mounted outdoors and with the cables exiting upwards, it is essential to have a good seal by sticking the insulation disk to the antenna before attaching it to the antenna arm.
Mounting instructions LANCOM AirLancer ON-Q360ag
Attaching the antenna to the antenna bracket The antenna is attached to the antenna bracket by means of the antenna arm. To do this, place the antenna-arm joint socket onto the joint head of the antenna bracket. Tighten this joint with the wing screw or hexagon socket screw supplied. Whichever screw you use, please be sure to use the washer supplied.
Attaching the antenna to a suspended ceiling This requires a 3-cm diameter hole in the suspended ceiling. First stick the insulation disk to the antenna. This acts as a washer and protects the ceiling and the antenna. Insert the cables and the screw thread through the hole in the ceiling. Then screw the locking screw onto the screw thread and tighten it.
Mounting Instructions LANCOM AirLancer ON-Q360ag
Important infoirmation
Working responsibly with high frequencies For compliance with protection requirements of the EU directive 2014/53 and EN 62479 in relation to the basic limits for human safety in electromagnetic fields and the “FCC Policy on Human Exposure to Radiofrequency Electromagnetic Fields”, it is essential to configure the accurate antenna gain value in the Wi-Fi router or Wi-Fi access point.
Electrical and electronic equipment law In the interests of recycling, please do not dispose of electrical and electronic waste in your household garbage. Ensure that your electrical and electronic waste is disposed of in accordance with the regulations in your country.
Proper handling of antenna cables Antenna cables are sensitive RF cables. During installation it is important that the cables are not creased, and bent as little as possible, otherwise the antenna will suffer a loss of performance. Do not coil the antenna cable in tight loops.
Antenna gain and terminating unused antenna connectors on the access point It is essential for unused antenna connectors on the access point to be terminated with the supplied rod antenna. The terminating resistor supplied with the adapter AirLancer AN-RPSMA-NJ is suitable for use with indoor access points. In addition, you must disable the unused antenna connectors in LCOS (changing the antenna grouping of the respective WLAN module), and configure the antenna gain of the antenna. The settings can be found in LANconfig under: Configuration > Wireless LAN > General > Physical WLAN settings > Radio
Radiation patterns
300 270
2.4 & 5 GH0z h-plane
5
330
30
0
-5
-10
-15
-20
-25
-30
-35
-40
60 90
240
210 180
120 150
2,400 MHz
2,500 MHz
5,150 MHz
300
5,400 MHz
5,900 2410 MHz MHz 2470 MHz
5000 MHz 5300 MHz
270
5800 MHz
2.4 & 5 GHz e-plane
0 5
330
30
0
-5
-10
-15
-20
-25
60 90
240
120
210
150
180
2410 MHz 2470 MHz 5000 MHz 5300 MHz 5800 MHz
Mounting Instructions LANCOM AirLancer ON-Q360ag
Technical details Frequency range Antenna characteristics Radiation characteristics
Recommended use VSWR Gain
Mechanical details Size Weight Temperature range Color Material Mounting options Cables, connectors Item Warranty Item number Package content
2,400 – 2,500 MHz, 4,900 – 5,900 MHz
horizontal (2.4 GHz) 360° vertical (2.4 GHz) 60° horizontal (5 GHz) 360° vertical (5 GHz) 33° Hotspot, coverage of open spaces 2.0:1 max. 2.4 GHz 4 dBi max. 5 GHz 4 dBi max.
26 x 16 cm (height x diameter) 950 g -30°C to 70°C light grey UV-resistant plastic Wall, pole, and ceiling mounting 4 x 91.4 cm UV-resistant RG58 cable with N-plug connector
2 years for AirLancer and accessories 61246 Antenna, insulation disk, antenna arm, antenna bracket, locking screw, fastening bolts (2x wall mounting, hexagon socket screw/wing screw with washer to connect antenna arm to antenna bracket), Quick Reference Guide
LANCOM Systems GmbH A Rohde & Schwarz Company Adenauerstr. 20/B2 52146 Wuerselen | Germany info@lancom.de | lancom-systems.com
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 111724 03/2025
Documents / Resources
 |
LANCOM SYSTEMS ON-Q360AG Air Lancer [pdf] Instruction Manual ON-Q360AG Air Lancer, ON-Q360AG, Air Lancer, Lancer |