“
Specifications
- Supply: 220 – 240 V
- Supply current: 4 mA
- Control system: Radio support IEEE 802.15.4
- Frequency band: 2.4 GHz
- Max radio tx power: +8 dBm
- DALI line current: 2 mA
- Wiring: 1 – 4 mm2 Strip 8 – 10 mm
- Material: PC UV stabilised, toughened glass, aluminium
- Ingress protection: IP20
Product Usage Instructions
- Remove the product from the box and inspect it for any damage.
If damaged, do not install. - If satisfactory, proceed with installation:
- Ensure safety warnings are adhered to.
- Optional: Connect the two DALI terminals to the DALI line
following wiring regulations. - Remove the front plate using a screwdriver in the receptacle at
the bottom of the frame. - Cut out the hole and insert the wallbox if applicable.
- Insert provided screws into the frame and attach to the
pre-mounted wallbox/c-clip.
FAQ
Q: Can I install the product myself?
A: No, this product must only be installed by a licensed
electrician.
Q: What should I do if I encounter a damaged product?
A: If you believe the product to be damaged or unsound, do not
install it. Please return it to the place of purchase for
replacement.
Q: What is the Ingress Protection rating of the product?
A: The Ingress Protection rating is IP20.
Q: How should I remove the front plate for installation?
A: Insert a screwdriver (min. 5.5pt) into the receptacle at the
bottom of the frame. Twist left and right to release the cover; do
not lever.
“`
Smart switch w/3-buttons zc-ss-3sw
Dimensions (mm)
zc-ss-3sw Fixing centres 84 mm Dimensions W75 / H117 / D34 mm
116
84
75
9.5 18.5 6
With c-clip
zc-ss-3sw-eu Fixing centres 55 mm Dimensions W86 / H86 / D34 mm
90
Product range
Order code zc-ss-3sw-blk zc-ss-3sw-wht zc-ss-3sw-eu-blk zc-ss-3sw-eu-wht
Description
Smart switch with 3 buttons to suit 84 mm wall mount, black
Smart switch with 3 buttons to suit 84 mm wall mount, white
Smart switch with 3 buttons to suit 55 mm wall mount, black
Smart switch with 3 buttons to suit 55 mm wall mount, white
Specifications
Supply
220 – 240 V
Supply current
4 mA
Control system
IEC62386-104 over Thread® / DALI-2
Radio support
IEEE 802.15.4
Frequency band
2.4 GHz
Max radio tx power +8 dBm
DALI line current
2 mA
Wiring
1 – 4 mm2 Strip 8 – 10 mm
Operating temperature 0 to 55°C
Material
PC UV stabilised, toughened glass, aluminium
Ingress protection IP20
Safety information
This product must only be installed by a licensed electrician. Before commencing installation turn off and isolate the
electrical supply.
There are no user serviceable parts, attempting to service any part of the product will void the warranty
DALI is not SELV and as such should be treated as LV. As the installer, it is your responsibility to ensure you comply
to all relevant building and safety codes. Refer to application standards for the relevant rules.
Isolate electrical supply before removing faceplate. Circuit-board is NOT isolated.
86
9.5 18.5 6
55
System overview: modes
1 104 mode is enabled after the device has been added to a 104 application controller such as zc-iot-fc.
Wireless switch IEC 62386-301
zc-iot-fc IEC 62386-103
IEC 62386-104 over Thread
2 104 + 101 Bridge mode is enabled after the device has been added to a 104 controller and a 101 power supply has been connected to the
DALI terminals.
PIR sensor
zc-psu-70
IEC 62386-303
IEC 62386-101
Wireless switch IEC 62386-301
IEC 62386-101
IEC 62386-104 over Thread
zc-iot-fc IEC 62386-103
DALI luminaire IEC 62386-102
3 101 mode is enabled after a 101 power supply has been connected to the DALI terminal and the device has not been added to a 104 application controller.
Wireless switch IEC 62386-301
Power supply IEC 62386-101
Application controller IEC 62386-103
LN
DA DA
IEC 62386-101
Ethernet
0553501_V 1.2
Last updated 01 / 04 / 25
Information is subject to change without notice, E&OE
Installation
Remove the product from the box and inspect it for any damage. If you believe the product to be damaged or otherwise unsound, do not install the product. Please pack it back into its box and return it to the place of purchase for replacement.
If the product is satisfactory, proceed with the installation: 1 Ensure safety warnings are adhered to.
2 Optional: Connect the two DALI terminals to the DALI line ensuring wiring regulations are followed. DALI is not polarised. DALI is not SELV and as such must be treated as LV. Do not connect DALI to any mains voltages.
3 Remove front plate by inserting a screwdriver (min. 5.5pt) into receptacle at the bottom of the frame. Twist left, twist right, to release cover, do not lever.
4 Cut-out the hole, insert wallbox if applicable.
5 Insert provided screws into frame and attach to pre-mounted wallbox/c-clip.
6 Not applicable to eu versions. Latch cover on top of frame to clip base back into frame, attached on the wall.
3
zc-ss-3sw-eu
5 4 Cut-out 56 x 75 mm
zc-ss-3sw
Frame
Base
C-Clip 5
6
Clip in at top
Wiring diagram
Input configuration
L N
DA
2 Optional
DA
Wire preparation
L N DADA
4 mm
Ensure each terminal is lined up with correct marking on the product label
Configuration
By default the device is configured with 1/2/3 control device instances with LED indicator. Actual function is dependant on the configuration of a DALI-2 application controllers connected to the DALI line, or the Wireless application controller.
By default the device will configure its mode of operation depending on what has been commissioned.
ECD operating mode
128 (0x80) Bridge mode (default): Device acts as a bridge between Thread 104 interface and DALI devices connected via 101 interface
129 (0x81) Beacon mode: Device broadcasts Bluetooth beacons and communicates via 104 interface if Thread network is commissioned otherwise via 101 interface. For more information on how to configure Beacons visit support. zencontrol.com
130 (0x82) Bridge disabled: Device communicates via both 104+101 interface, however, bridge mode is disabled (i.e. Devices connected on the 101 interface will not be available on the Thread 104 system)
Notice
For more information on compliant software see our website
zencontrol.com
4 Cut-out 56 x 75 mm
Frame Tab must face down
zencontrol.com
Base
© zencontrol
Documents / Resources
 |
zencontrol zc-ss-3sw-blk Smart Switch with 3 Buttons [pdf] Installation Guide zc-ss-3sw-blk, zc-ss-3sw-wht, zc-ss-3sw-eu-blk, zc-ss-3sw-eu-wht, zc-ss-3sw-blk Smart Switch with 3 Buttons, zc-ss-3sw-blk, Smart Switch with 3 Buttons, Switch with 3 Buttons, 3 buttons, Buttons |