Mean Well IDPV-65 65W PWM Output LED Driver User Manual

IDPV-65 series is a 65W PCB type AC/DC LED driver featuring the constant voltage mode PWM style output design. IDPV-65 operates from 180-295VAC and offers models with different rated voltages ranging between 12V and 60V. Thanks to the high efficiency of up to 90%, with the fanless design, the entire series is able to operate for -20 C-+40 C ambient temperature under free air convection. IDPV-65 is equipped with various function options, such as dimming methodologies, so as to provide design flexibility for the LED lighting systems.

Model Encoding

Type	Function
Blank	2 in 1 dimming (0-10VDC and 10V PWM)
A	2 in 1 dimming and Auxiliary DC output

SPECIFICATION

MODEL		IDPV-650-12	ippv.650-24		DPV-6036		IDPV-6C-48		IDPV-61:1-60
OUTPUT	DC VOLTAGE	12V	24V		36V		48V		60V
	RATED CURRENT	4.2A	2.4A		1.8A		1.35A		1.08A
	RATED POWER	50.4W	57.6W		64.8W		64.8W		64.8W
	DIMMING RANGE	0-100%
	VOLTAGE TOLERANCE	± 10%
	PWM FREQUENCY (Typ.)	1KFtz(± 20%)
	SETUP TIME Note.3	500ms /230VAC
	AUXILIARY DC OUTPUT Nob/	Nominal 12V(deviation 11.4-12.6)@50mA forA-Type only
INPUT	VOLTAGE RANGE Note.2	180 – 295VAC 254 – 417VDC (Please refer to ‘STATIC CHARACTERISTIC’ section)
	FREQUENCY RANGE	47 – 63Hz
	POWER FACTOR crypt.)	PF>0.95/230VAC, PF>0.9/277VAC@ifull load (Please refer to the ‘POWER FACTOR (PF) CHARACTERISTIC’ section)
	TOTAL HARMONIC DISTORTION	THD< 20%(@loadM0%/230VAC; @load.475%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION’ section)
	EFFICIENCY (Typ.)	85%		I87%		I88%		I89%		I90%
	AC CURRENT (Typ.)	0.4A/230VAC 0.3A/277VAC
	INRUSH CURRENT(Typ.)	COLD START 30A(twidth=270ps measured at 50% (peak) at 230VAC: Per NEMA 410
	MAX. No. of PSUs on 16A CIRCUIT BREAKER	32 units (circuit breaker of type B)/ 32 units (circuit breaker of type C) at 230VAC
	LEAKAGE CURRENT	<0.75mA/ 277VAC
	NO LOAD POWER CONSUMPTION	<0.5W
PROTECTION	SHORT CIRCUIT	Shutdown 0/P voltage, re-power on to recovery
	OVER CURRENT	105 -115%
		Protection type : Hiccup mode, recovers automatically after fault condition is removed
ENVIRONMENT	WORKING TEMP.	Ta=-20 – +40 C (Please refer to” OUTPUT LOAD vs TEMPERATURE’ section)
	WORKING HUMIDITY	20 – 90% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 – +80^°C, 10 – 95% RH
	TEMP. COEFFICIENT	±0.03%/C (0 – 40^°C)
	VIBRATION	10 – 500Hz, 2G 10min./Tricycle, period for 60min . each along X. Y. Z axes
SAFETY & EMC	SAFETY STANDARDS	UL8750.CSA C22.2 NO.250.13-12;ENEC EIS EN/ EN61347-1 & BS EN!EN61347-2-13 independent, BS EN!EN62384approved
	WITHSTAND VOLTAGE	I/P-0/P:3.75KVAC
	ISOLATION RESISTANCE	I/P-0/P:100M Ohms / 500VDC / 25^°Ci 70% RH
	EMC EMISSION	Compliance to BS E N/E N55015, BS E N/EN61000-3-2 Class C (tRbad:=60%); BS EN/EN61000-3-3
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547.1ight industry level(surge immunity: Lthe-Line:1KV)
OTHERS	MTBF	3720.1K hrs min. Telcordia SR-332 (Bellcore); 398.8K hrs min. MIL-HDBK-217F (25^°C)
	DIMENSION	130’67.5’22mm (L’IN*F1)
	PACKING	0.15Kg;81pcs/13Kg/ 1.46CUFT
NOTE	1. All parameters NOT specially mentioned we measured at 230VAC input, rated current, and 25’C of ambient temperature. 2. Deleting may be needed under low input voltages. Please refer to b ‘STATIC CHARACTERISTIC’ sections tar details. 3. Length of setup time is measured at cold first start. Turning OWOFF the driver may lead to an increase in the setup time. 4. Aux. 12V will be damaged with a short circuit It will not be available with dimming off or output no load condition. 5. The (liver is considered a component that a be operated in combination with final equipment Since EMC performance will be affected by the complete installation. the final equipment manufacturers must requalify EMC Directive on the complete installation again. ※ Product Liability Disclaimer: For detailed information, please refer to https://www.meamwell.con/servicedisclaimer.aspx

DIMMING OPERATION

※ Dimming principle for PWM style output

Dimming is achieved by varying the duty cycle of the output current.

※ 2 in 1 dimming function
◎ Applying additive 0 ~ 10VDC

◎ Applying additive 10V PWM signal (frequency range 300Hz~3KHz):

Note

Min. duty cycle of output current is about 8% and the output current is not defined when 0%< Iout<8%.

The duty cycle of output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.
To ensure the dimming effect, total power must be over 45W at 100% duty cycle.