soundcore Bluetooth Speaker User Manual

Soundcore Motion+ is equipped with High-Resolution Audio. This specialty gives the speaker a better sound quality by referring to digital processes that allow
playback of music using higher sampling rates.
Note: Soundcore Motion+ supports Qualcomm® aptX™️.

a. Bluetooth mode

	Slowly Flashing Blue (Fade in and out)	Bluetooth Pairing Mode Note: starts to connect to previous connected the mobile device when the speaker is turned on.
	Solid Blue	Connected to a device

Enter True Wireless Stereo Group Mode / Disconnect True Wireless Stereo

	Slow Flashing White	True Wireless Stereo Group Mode
	Solid White	Connected to True Wireless Stereo Note: When True Wireless Stereo group is successful, the Bluetooth indicator on both the main and secondary speakers will turn solid white.

Music

	Play / Pause
	Play Next Song
	Play Next Song
	Press to turn Bass on
	Press once to activate bass Note: Press again to switch back to Normal Equalizer
	Activate Siri / Other Voice Control Software
	Volume Up / Down

Mobile phone

	Answer Call / End Call
	Reject Call / Switch between a call on hold and an active call
	End current call and answer incoming call / End current call and switch to call on hold
	Switch audio source between Speaker and Phone

	Solid Blue	On a Call
	Flashing Blue	Incoming Call

When turned on, Soundcore Motion+ will automatically connect to the last connected device if available. If not, press the Bluetooth button to activate pairing mode.
To pair a different device, press the Bluetooth button to re-enter pairing mode. Then repeat the pairing steps.
Having connection problems? Remove Soundcore Motion+ from your device’s Bluetooth history and ensure it’s less than 3 feet away. Then try pairing again. To get the best sound quality, make sure there is a clear line of sight between the connected device and your speaker.

b. AUX-In mode

Plugging in an audio cable will automatically switch to AUX mode.
When using AUX mode, control audio playback via the connected device.

Charging your Soundcore Motion+

	Slow Flashing Red	Low Battery
	Solid Red	Charging
		Fully Charged

Use the included USB cable to charge your Soundcore Motion+ and make sure it is fully charged before its first use.
USB type C cable only supports charge in, it does not support charge out.
Disconnect your speaker from the charger when fully charged. Do not charge your speaker for extended periods.
When not in use, store your speaker in a cool place.

Specifications

Specifications are subject to change without notice.

Input: 5 V 2 A
Audio output: 30 W
Battery capacity : max.6700mAh
Charging time : Approximately 4 hours(When power is off and the adapter must be at least 5V/2A)
Playtime (varies by volume level and music content): 12 hours
Size: 257 x 79 x 81 mm / 10.1 x 3.1 x 3.2 inch
Weight (without packaging): 1050 g / 37 oz
Bluetooth version: V 5.0
Bluetooth range: 30m/99ft
Sound Frequency Range: 50Hz~40kHz

Customer Service

18-month limited warranty
Lifetime technical support
service@soundcore.com
+1 (800) 988 7973 (US) Mon-Fri 9:00 – 17:00 (PT)
+44 (0) 1604 936200 (UK) Mon-Fri 6:00 – 11:00 (GMT)

Qualcomm® aptX™️ Technical specifications
Compression ratio: 4:1
Word Depth: Support 16bit and 24bit
Decoding delay: Sample Rate 48kHZ<2ms
Dynamic range: 16bit>92dB, 24bit>120dB
Data rates: 352kbps
Decode mode: Stereo
Qualcomm aptX is a product of Qualcomm Technologies International, Ltd.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission. aptX is a trademark of
Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.