KTC H27T22C-3 LCD Monitor Display User Guide

Upon unboxing, carefully remove all packaging materials. Connect the power adapter to the power input port on the device. Plug the power adapter into a suitable power outlet.

Powering On

Press the power button located on the device to power it on.
Wait for the indicator light to turn green, indicating the device is ready for use.

Functionality

This product is designed for XYZ purposes. Use the control panel or remote control to navigate through different modes and settings.

Maintenance

Regularly clean the device with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials that may damage the surface.

INTRODUCTION

Please read the User Guide carefully and keep it properly. The pictures involved in the User Guide are for reference only; please refer to the actual product for details.

Important Safety Precautions

Please read all the instructions carefully before using the product.

When cleaning the display, please unplug the power cord. Please wipe the display with a soft, wet cloth instead of liquid or spray cleaner. Please use LCD screen cleaner in case of a stubborn stain.
Do not use accessories that are not recommended by the manufacturer, as they may be dangerous.

When unplugging the power cord of the display or the power adapter, please hold the power plug with your hand rather than directly pulling the power cord to unplug it.
Do not place the display near water, such as a bathtub, washbasin, kitchen sink, or washing machine. Do not place the display on wet ground or near the swimming pool. Do not use fingers or hard objects to press the surface of the LCD screen.

The grooves and holes on the shell or at the back and bottom of the display are designed for the ventilation and heat dissipation of the components to ensure reliable operation. So, do not put the display on the bed, sofa, carpet, or similar surfaces of other objects to prevent the heat dissipation holes from blocking, and do not place the display near or above the radiator or heater. In addition, do not place the display in an embedded device unless adequate ventilation is provided.
Only the power supply type shown on the nameplate can be used for the display. Please feel free to consult the display dealer or the local power supply administration if you have any doubts about your power supply type.

For safety, the display or the power adapter uses a power cord with a three-prong plug, whose third prong can only be properly grounded when used with a properly grounded socket. If your socket cannot match the plug, please contact an electrician to replace your original socket so that the plug can give full play to ensuring safety.
As you may face high voltage or other dangers after removing the shell, do not repair the display by yourself. You can have it repaired by qualified maintenance personnel.

Please unplug the power cord of the display or the power adapter from the socket, and contact qualified maintenance personnel for repairing the display when the following cases occur.
- a. The power cord or the plug is damaged or worn out.
- b. The display has been dropped from high or the shell is damaged.
- c. Any obvious abnormality.
Please place the display in a well-ventilated environment, which is away from strong light, high temperature, or humidity.

The temperature for the display store is -20°C ~ 55 °C, or it may be permanently damaged.
The monitor screen is fragile, so please be careful when moving or handling it!

Product Introduction

It is a kind of high-performance intelligent multiple frequency scanning display, which adopts active matrix thin-film transistor LED-backlit LCD.
The display is controlled through the microcomputer MCU digital technology.

It is compact and lightweight, which is suitable for narrow working spaces.
Before installation, please check whether the following accessories are complete in the packing box.

LCD ×1
Base x1
Power Adapter ×1
DP Signal Cable x1
Power Cord ×1
User Guide x1 (including warranty card)
Base Screws ×3 (including 1 spare screw)
If any of the above accessories are missing, please contact with product distributor immediately.
Notice: Specific accessories are required in order to prevail in kind. Please keep packing materials for future movement.

Keys And Interfaces

Signal Cable Connection
- Connect the signal cable to the HDMI or DP signal output port on the PC, then connect the other end of the signal cable to the corresponding signal input port on the LCD.

Headset Connection
- After connecting the headset, there will be audio output, and it also supports external loudspeakers.

Upgrade through USB
- USB2.0: 5V 0.5A
- The USB port is only used to update display firmware from a USB mobile device. Do not insert any other devices.

Power Indicator

The constant indicator means that the display is in normal operation; the flash indicator represents no signal state. Under the energy conservation state, the display will normally work if the signal is provided again.
The display is still powered on in the standby state. Thus, unplug the power cord when you do not use the display for safety.

Base And Wall Mount

Installing the Base
If you want to remove the whole base, do the following
Wall mounting screw size: M4*10mm

Mounting Location

Install on the hase

Ventilation

Please leave a space around the display with a size at least as shown in the figure.
Do not cover the ventilation holes or insert anything into the shell.
Unless there are proper ventilation conditions and adequate ventilation space around the display, do not place the display within a limited space, such as a book cabinet or a built-in closet.

Installation Guide

The display should be installed near an AC power socket that can be easily pluggable.
It is recommended to use a suitable base for safety purposes.
To prevent injury, the display should be placed on a smooth horizontal plane.
Do not place the display where it may be subjected from mechanical vibration.
Do not place the display where insects may enter.
Do not place the display directly facing an air conditioner, or the internal panel may condense, leading to faults.
Do not place the display where there is a strong electromagnetic field, or it will be interfered with and damaged by the electromagnetic waves.

Safety Protection

When the PC video signal exceeds the frequency range of the display, the display will disable the line and field synchronizing signals to protect the display.
Under these circumstances, you must set the output frequency of the PC to an acceptable range for the display to work properly.

Power Management System

Remark: All technical specifications in the User Guide and on the external packing are allowed to change without prior notice.

If there is a subtle difference between the User Guide and the actual operation, the latter shall prevail.

Product Technical Specifications

Simple Problems Disposal

Product Warranty Card

Customer Name
Tel
Address
Model
Device Number
Purchase Date

Warranty Rules

We provide you with a three-year free warranty from the date of purchase or as agreed in the contract.
The following cases are not covered by the warranty:
- Failure or damage caused by artificial or natural disasters.
- Failure caused by not following the operation method and precautions written in the User Guide.
- Failure caused by user disassembly.
The liability scope of the warranty card is limited to the maintenance of the product, without covering any other liability.
If you are not sure about the repair and warranty of the machine after the warranty period, please visit the website EN.KTCPLAY.COM for the warranty policy.
- Notice: Please fill out the card and return it to us when you apply for a warranty.

More Information

Please scan the QR code or visit EN.KTCPLAY.COM
Any questions or comments.
Please contact: support@ktcplay.com
support.eu@ktcplay.com Europe
To care for and protect the earth better, please send it to a local manufacturer with nationally recognized qualifications for recycling according to the national applicable laws and regulations on recycling of waste electrical and electronic products when you no longer need this product or at the end of its service life.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc., in the United States and other countries.

Frequently Asked Questions

How do I change the settings on the device?

You can change the settings using the control panel or the remote control that comes with the product. Refer to the user manual for detailed instructions on adjusting settings.

Can this product be used outdoors?

This product is designed for indoor use only. Using it outdoors may expose it to environmental conditions that could damage the device.

What should I do if the device stops working?

If you encounter any issues with the device, first check the power supply and connections. If problems persist, contact our customer support for assistance.

Documents / Resources

KTC H27T22C-3 LCD Monitor Display [pdf] User Guide
H27T22C-3 LCD Monitor Display, H27T22C-3, LCD Monitor Display, Monitor Display, Display

References

User Manual

KTC H27T22C-3 LCD Monitor Display

Product Information

Product Usage Instructions