KOOL SEAL Safety Data Sheet Instruction Manual

SAFETY DATA SHEET
KSRV08120

Section 1. Identification

Product name KOOL SEAL® RV Elastomeric Base Coat
Product code KSRV08120
Other means of

Identification

Not available.
Product type Liquid.

Relevant identified uses of the substance or mixture and uses advised against
Paint or paint-related material.

Manufacturer KST Coatings

A Business Unit of the Sherwin-Williams Co.

101 W. Prospect Avenue

Cleveland, OH 44115

Emergency telephone number of the company US / Canada: (216) 566-2917

Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year

Product Information Telephone Number US / Canada: (888) 321-5665

Mexico: Not Available

Regulatory Information
Telephone Number
US / Canada: (216) 566-2902

Mexico: Not Available

Transportation Emergency

Telephone Number

US / Canada: (216) 566-2917

Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year

Section 2. Hazards identification

OSHA/HCS status This material is considered hazardous by the OSHA Hazard Communication Standard

(29 CFR 1910.1200).

Classification of the

substance or mixture

SKIN CORROSION/IRRITATION – Category 2

SERIOUS EYE DAMAGE/ EYE IRRITATION – Category 2A

SKIN SENSITIZATION – Category 1

CARCINOGENICITY – Category 2

GHS label elements

Hazard pictograms

Warning
Signal word Warning
Hazard statements Causes serious eye irritation.

Causes skin irritation.

May cause an allergic skin reaction.

Suspected of causing cancer.

Precautionary statements

General

Read label before use.  Keep out of reach of children.  If medical advice is needed,

have product container or label at hand.

 

Prevention Obtain special instructions before use.  Do not handle until all safety precautions have

been read and understood.  Wear protective gloves.  Wear eye or face protection.

Wear protective clothing.  Avoid breathing vapor.  Wash hands thoroughly after handling.

Contaminated work clothing must not be allowed out of the workplace.

Response IF exposed or concerned:  Get medical attention.  IF ON SKIN:  Wash with plenty of

soap and water.  Wash contaminated clothing before reuse.  If skin irritation or rash

occurs:  Get medical attention.  IF IN EYES:  Rinse cautiously with water for several

minutes.  Remove contact lenses, if present and easy to do. Continue rinsing.  If eye

irritation persists:  Get medical attention.

Storage Store locked up.
Disposal Dispose of contents and container in accordance with all local, regional, national and

international regulations.

Supplemental label

Elements

WARNING:  This product contains chemicals known to the State of California to cause

cancer and birth defects or other reproductive harm.

Please refer to the SDS for additional information. Keep out of reach of children.  Do not

transfer contents to other containers for storage.

Hazards not otherwise

classified

None known.

Section 3. Composition/information on ingredients

Substance/mixture Mixture
Other means of identification Not available.

CAS number/other identifiers

Ingredient name % by weight CAS number
Calcium Carbonate

Titanium Dioxide

Heavy Paraffinic Oil

Light Aliphatic Hydrocarbon

1,2,4-Trimethylbenzene

Light Aromatic Hydrocarbons

1,3,5-Triazine-triethanol

≥10 – <20

≤3

≤1

<1

≤0.3

≤0.3

≤0.3

1317-65-3

13463-67-7

64742-65-0

64742-47-8

95-63-6

64742-95-6

4719-04-4

Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the

concentrations applicable, are classified as hazardous to health and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Section 4. First-aid measures

Description of necessary first aid measures

Eye contact Immediately flush eyes with plenty of water, occasionally lifting the upper and lower

eyelids.  Check for and remove any contact lenses.  Continue to rinse for at least 10

minutes.  Get medical attention.

Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing.  If

not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial

respiration or oxygen by trained personnel.  It may be dangerous to the person providing

aid to give mouth-to-mouth resuscitation.  Get medical attention.  If unconscious, place

in recovery position and get medical attention immediately.  Maintain an open airway.

Loosen tight clothing such as a collar, tie, belt or waistband.

 

Skin contact Wash with plenty of soap and water.  Remove contaminated clothing and shoes.  Wash

contaminated clothing thoroughly with water before removing it, or wear gloves.

Continue to rinse for at least 10 minutes.  Get medical attention.  In the event of any

complaints or symptoms, avoid further exposure.  Wash clothing before reuse.  Clean

shoes thoroughly before reuse.

Ingestion Wash out mouth with water.  Remove dentures if any.  Remove victim to fresh air and

keep at rest in a position comfortable for breathing.  If material has been swallowed and

the exposed person is conscious, give small quantities of water to drink.  Stop if the

exposed person feels sick as vomiting may be dangerous.  Do not induce vomiting

unless directed to do so by medical personnel.  If vomiting occurs, the head should be

kept low so that vomit does not enter the lungs.  Get medical attention.  Never give

anything by mouth to an unconscious person.  If unconscious, place in recovery position

and get medical attention immediately.  Maintain an open airway.  Loosen tight clothing

such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed

Potential acute health effects

Eye contact Causes serious eye irritation.
Inhalation No known significant effects or critical hazards.
Skin contact Causes skin irritation.  May cause an allergic skin reaction.
Ingestion No known significant effects or critical hazards.

Over-exposure signs/symptoms

Eye contact Adverse symptoms may include the following:

pain or irritation

watering

redness

Inhalation No specific data.
Skin contact Adverse symptoms may include the following:

irritation

redness

Ingestion No specific data.

 

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician Treat symptomatically.  Contact poison treatment specialist immediately if large

quantities have been ingested or inhaled.

Specific treatments No specific treatment.
Protection of first-aiders No action shall be taken involving any personal risk or without suitable training.  It may

be dangerous to the person providing aid to give mouth-to-mouth resuscitation.  Wash

contaminated clothing thoroughly with water before removing it, or wear gloves.

 

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Extinguishing media

Suitable extinguishing

media

Use an extinguishing agent suitable for the surrounding fire.
Unsuitable extinguishing

Media

None known.
Specific hazards arising

from the chemical

In a fire or if heated, a pressure increase will occur and the container may burst.

 

Hazardous thermal

decomposition products

Decomposition products may include the following materials:

carbon dioxide

carbon monoxide

metal oxide/oxides

Special protective actions

for fire-fighters

Promptly isolate the scene by removing all persons from the vicinity of the incident if

there is a fire.  No action shall be taken involving any personal risk or without suitable

training.

Special protective

equipment for fire-fighters

Fire-fighters should wear appropriate protective equipment and self-contained breathing

apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures

For non-emergency

personnel

No action shall be taken involving any personal risk or without suitable training.

Evacuate surrounding areas.  Keep unnecessary and unprotected personnel from

entering.  Do not touch or walk through spilled material.  Avoid breathing vapor or mist.

Provide adequate ventilation.  Wear appropriate respirator when ventilation is

inadequate.  Put on appropriate personal protective equipment.

For emergency responders If specialized clothing is required to deal with the spillage, take note of any information in

Section 8 on suitable and unsuitable materials.  See also the information in “For nonemergency

personnel”.

Environmental precautions Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains

and sewers.  Inform the relevant authorities if the product has caused environmental

pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up

Small spill Stop leak if without risk.  Move containers from spill area.  Dilute with water and mop up

if water-soluble.  Alternatively, or if water-insoluble, absorb with an inert dry material and

place in an appropriate waste disposal container.  Dispose of via a licensed waste

disposal contractor.

Large spill Stop leak if without risk.  Move containers from spill area.  Approach release from

upwind.  Prevent entry into sewers, water courses, basements or confined areas.  Wash

spillages into an effluent treatment plant or proceed as follows.  Contain and collect

spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or

diatomaceous earth and place in container for disposal according to local regulations

(see Section 13).  Dispose of via a licensed waste disposal contractor.  Contaminated

absorbent material may pose the same hazard as the spilled product.  Note: see

Section 1 for emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling

Protective measures Put on appropriate personal protective equipment (see Section 8).  Persons with a

history of skin sensitization problems should not be employed in any process in which

this product is used.  Avoid exposure – obtain special instructions before use.  Do not

handle until all safety precautions have been read and understood.  Do not get in eyes

or on skin or clothing.  Do not ingest.  Avoid breathing vapor or mist.  If during normal

use the material presents a respiratory hazard, use only with adequate ventilation or

wear appropriate respirator.  Keep in the original container or an approved alternative

made from a compatible material, kept tightly closed when not in use.  Empty containers

retain product residue and can be hazardous.  Do not reuse container.

Advice on general

occupational hygiene

Eating, drinking and smoking should be prohibited in areas where this material is

handled, stored and processed.  Workers should wash hands and face before eating,

drinking and smoking.  Remove contaminated clothing and protective equipment before

entering eating areas.  See also Section 8 for additional information on hygiene

measures.

Conditions for safe storage,

including any

incompatibilities

Store in accordance with local regulations.  Store in original container protected from

direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials

(see Section 10) and food and drink.  Store locked up.  Keep container tightly closed

and sealed until ready for use.  Containers that have been opened must be carefully

resealed and kept upright to prevent leakage.  Do not store in unlabeled containers.

Use appropriate containment to avoid environmental contamination.  See Section 10 for

incompatible materials before handling or use.

Section 8. Exposure controls/personal protection

Control parameters

Occupational exposure limits (OSHA United States)

Ingredient name CAS # Exposure limits
Calcium Carbonate 1317-65-3 OSHA PEL (United States, 5/2018).

TWA: 5 mg/m³ 8 hours. Form: Respirable

fraction

TWA: 15 mg/m³ 8 hours. Form: Total dust

NIOSH REL (United States, 10/2016).

TWA: 5 mg/m³ 10 hours. Form: Respirable

fraction

TWA: 10 mg/m³ 10 hours. Form: Total

Titanium Dioxide 13463-67-7 ACGIH TLV (United States, 3/2019).

TWA: 10 mg/m³ 8 hours.

OSHA PEL (United States, 5/2018).

TWA: 15 mg/m³ 8 hours. Form: Total dust

Heavy Paraffinic Oil 64742-65-0 OSHA PEL (United States, 5/2018).

TWA: 5 mg/m³ 8 hours.

ACGIH TLV (United States, 3/2019).

TWA: 5 mg/m³ 8 hours. Form: Inhalable

fraction

NIOSH REL (United States, 10/2016).

TWA: 5 mg/m³ 10 hours. Form: Mist

STEL: 10 mg/m³ 15 minutes. Form: Mist

Light Aliphatic Hydrocarbon 64742-47-8 ACGIH TLV (United States, 3/2019).

Absorbed through skin.

TWA: 200 mg/m³, (as total hydrocarbon

vapor) 8 hours.

1,2,4-Trimethylbenzene 95-63-6 ACGIH TLV (United States, 3/2019).

TWA: 25 ppm 8 hours.

TWA: 123 mg/m³ 8 hours.

NIOSH REL (United States, 10/2016).

TWA: 25 ppm 10 hours.

TWA: 125 mg/m³ 10 hours.

Light Aromatic Hydrocarbons

1,3,5-Triazine-triethanol

64742-95-6

4719-04-4

None.

None.

Occupational exposure limits (Canada)

Ingredient name CAS # Exposure limits
Titanium dioxide 13463-67-7 CA British Columbia Provincial (Canada,

5/2019).

TWA: 3 mg/m³ 8 hours. Form: Respirable

dust

TWA: 10 mg/m³ 8 hours. Form: Total dust

CA Quebec Provincial (Canada, 1/2014).

TWAEV: 10 mg/m³ 8 hours. Form: Total dust.

CA Alberta Provincial (Canada, 6/2018).

8 hrs OEL: 10 mg/m³ 8 hours.

CA Ontario Provincial (Canada, 1/2018).

TWA: 10 mg/m³ 8 hours.

CA Saskatchewan Provincial (Canada,

7/2013).

STEL: 20 mg/m³ 15 minutes.

TWA: 10 mg/m³ 8 hours.

Occupational exposure limits (Mexico)

CAS # Exposure limits

 

Appropriate engineering

controls

If user operations generate dust, fumes, gas, vapor or mist, use process enclosures,

local exhaust ventilation or other engineering controls to keep worker exposure to

airborne contaminants below any recommended or statutory limits.

Environmental exposure

controls

Emissions from ventilation or work process equipment should be checked to ensure

they comply with the requirements of environmental protection legislation.  In some

cases, fume scrubbers, filters or engineering modifications to the process equipment

will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures Wash hands, forearms and face thoroughly after handling chemical products, before

eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Contaminated work clothing should not be allowed out of the workplace.  Wash

contaminated clothing before reusing.  Ensure that eyewash stations and safety

showers are close to the workstation location.

Eye/face protection Safety eyewear complying with an approved standard should be used when a risk

assessment indicates this is necessary to avoid exposure to liquid splashes, mists,

gases or dusts.  If contact is possible, the following protection should be worn, unless

the assessment indicates a higher degree of protection:  chemical splash goggles.

Skin protection

Hand protection Chemical-resistant, impervious gloves complying with an approved standard should be

worn at all times when handling chemical products if a risk assessment indicates this is

necessary.  Considering the parameters specified by the glove manufacturer, check

during use that the gloves are still retaining their protective properties.  It should be

noted that the time to breakthrough for any glove material may be different for different

glove manufacturers.  In the case of mixtures, consisting of several substances, the

protection time of the gloves cannot be accurately estimated.

Body protection Personal protective equipment for the body should be selected based on the task being

performed and the risks involved and should be approved by a specialist before

handling this product.

Other skin protection Appropriate footwear and any additional skin protection measures should be selected

based on the task being performed and the risks involved and should be approved by a

specialist before handling this product.

Respiratory protection Based on the hazard and potential for exposure, select a respirator that meets the

appropriate standard or certification.  Respirators must be used according to a

respiratory protection program to ensure proper fitting, training, and other important

aspects of use.

Section 9. Physical and chemical properties

Appearance

Physical state Liquid.
Color Not available.
Odor Not available.
Odor threshold Odor threshold
pH 9
Melting point/freezing point Not available.
Boiling point/boiling range 100°C (212°F)
Flash point Closed cup: Not applicable.
Evaporation rate 0.09 (butyl acetate = 1)
Flammability (solid, gas) Not available.
Lower and upper explosive

(flammable) limits

Not available.
Vapor pressure 2.3 kPa (17.5 mm Hg) [at 20°C]
Vapor density 1 [Air = 1]
Relative density 1.16
Solubility Not available.
Partition coefficient: noctanol/water Not available.
Auto-ignition temperature Not available.
Decomposition temperature Not available.
Viscosity Kinematic (40°C (104°F)): >0.205 cm

/s (>20.5 cSt)

Molecular weight

Aerosol product

Not applicable.
Heat of combustion 0.861 kJ/g

Section 10. Stability and reactivity

Reactivity No specific test data related to reactivity available for this product or its ingredients.
Chemical stability The product is stable.
Possibility of hazardous

Reactions

Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to avoid No specific data.
Incompatible materials No specific data.
Hazardous decomposition

Products

Under normal conditions of storage and use, hazardous decomposition products should

not be produced.

 

Section 11. Toxicological information

Information on toxicological effects

Acute toxicity

Product/ingredient name Result Species Dose Exposure
Heavy Paraffinic Oil

1,2,4-Trimethylbenzene

Light Aromatic Hydrocarbons

1,3,5-Triazine-triethanol

LD50 Dermal

LD50 Oral

LC50 Inhalation Vapor

LD50 Oral

LD50 Oral

LD50 Oral

Rabbit

Rat

Rat

Rat

Rat

Rat

>5000 mg/kg

>5000 mg/kg

18000 mg/m³

5 g/kg

8400 mg/kg

763 mg/kg

4 hours

Irritation/Corrosion

Product/ingredient name Result Species Dose Exposure Observation
Titanium Dioxide

Light Aromatic Hydrocarbons

Skin – Mild irritant

Eyes – Mild irritant

Human

Rabbit

72 hours 300

ug I

24 hours 100

Ul

Sensitization

Not available.

Mutagenicity

Not available.

Carcinogenicity

Not available.

Classification

Product/ingredient name OSHA IARC NTP
Titanium Dioxide 2B

Reproductive toxicity

Not available.

Teratogenicity

Not available.

Specific target organ toxicity (single exposure)

Name Category Route of exposure Target organs
Calcium Carbonate

Light Aliphatic Hydrocarbon

1,2,4-Trimethylbenzene

Light Aromatic Hydrocarbons

Category 3

Category 3

Category 3

Category 3

Category 3

Category 3

Not applicable.

Not applicable.

Not applicable.

Not applicable.

Not applicable.

Not applicable.

Respiratory tract

irritation

Narcotic effects

Respiratory tract

irritation

Respiratory tract

irritation

Narcotic effects

Respiratory tract

Irritation

Light Aliphatic Hydrocarbon

Light Aromatic Hydrocarbons

1,3,5-Triazine-triethanol

Category 2

Category 2

Category 1

Not determined

Not determined

Not determined

Not determined

Not determined

Not determined

Aspiration hazard

Name Result
Heavy Paraffinic Oil

Light Aliphatic Hydrocarbon

1,2,4-Trimethylbenzene

Light Aromatic Hydrocarbons

ASPIRATION HAZARD – Category 1

ASPIRATION HAZARD – Category 1

ASPIRATION HAZARD – Category 1

ASPIRATION HAZARD – Category 1

 

Information on the likelyroutes of exposure Not available.
Potential acute health effects
Eye contact Causes serious eye irritation.
Inhalation No known significant effects or critical hazards.
Skin contact Causes skin irritation.  May cause an allergic skin reaction.
Ingestion No known significant effects or critical hazards.
Symptoms related to the physical, chemical and toxicological characteristics
Eye contact Adverse symptoms may include the following:

pain or irritation

watering

redness

Inhalation No specific data.
Skin contact Adverse symptoms may include the following:

irritation

redness

Ingestion No specific data.
Delayed and immediate effects and also chronic effects from short and long term exposure

Short term exposure

Potential immediate

effects

Not available.
Potential delayed effects

Long term exposure

Not available.
Potential immediate

Effects

Not available.
Potential delayed effects Not available.
Potential chronic health effects Not available.
General Once sensitized, a severe allergic reaction may occur when subsequently exposed to

very low levels.

Carcinogenicity Suspected of causing cancer.  Risk of cancer depends on duration and level of

exposure.

Mutagenicity No known significant effects or critical hazards.
Teratogenicity No known significant effects or critical hazards.
Developmental effects No known significant effects or critical hazards.
Fertility effects No known significant effects or critical hazards.

Numerical measures of toxicity

Acute toxicity estimates

Not available.

Section 12. Ecological information

Toxicity

Product/ingredient name Result Species Exposure
Titanium Dioxide

Light Aliphatic Hydrocarbon

1,2,4-Trimethylbenzene

1,3,5-Triazine-triethanol

Acute LC50 >1000000 µg/l Marine water

Acute LC50 2200 µg/l Fresh water

Acute LC50 4910 µg/l Marine water

Acute LC50 7720 µg/l Fresh water

Acute EC50 26.1 ppm Fresh water

Acute LC50 39 ppm Fresh water

Fish – Fundulus heteroclitus

Fish – Lepomis macrochirus

Crustaceans – Elasmopus

pectenicrus – Adult

Fish – Pimephales promelas

Daphnia – Daphnia magna

Fish – Lepomis macrochirus

96 hours

4 days

48 hours

96 hours

48 hours

96 hours

Persistence and degradability
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Light Aromatic Hydrocarbons Readily
Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
1,2,4-Trimethylbenzene

Light Aromatic Hydrocarbons

243

10 to 2500

low

high

Mobility in soil
Soil/water partition

coefficient (KOC)

Not available.
Other adverse effects No known significant effects or critical hazards.

 

Section 13. Disposal considerations

Disposal methods :

The generation of waste should be avoided or minimized wherever possible.  Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements.  Dispose of surplus and non-recyclable products via a licensed waste disposal contractor.  Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled.  Incineration or landfill should only be considered when recycling is not feasible.  This material and its container must be disposed of in a safe way.  Care should be taken when handling emptied containers that have not been cleaned or rinsed out.  Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information

DOT

Classification

TDG

Classification

Mexico

Classification

IATA IMDG
UN number UN number Not regulated. Not regulated. Not regulated. Not regulated.
UN proper

shipping name

Transport

hazard class(es)

Packing group
Environmental

Hazards

No No No No No
Additional

Information

 

Special precautions for user Multi-modal shipping descriptions are provided for informational purposes and do not

consider container sizes. The presence of a shipping description for a particular

mode of transport (sea, air, etc.), does not indicate that the product is packaged

suitably for that mode of transport. All packaging must be reviewed for suitability

prior to shipment, and compliance with the applicable regulations is the sole

responsibility of the person offering the product for transport. People loading and

unloading dangerous goods must be trained on all of the risks deriving from the

substances and on all actions in case of emergency situations.

Transport in bulk according

to Annex II of MARPOL and

the IBC Code

Not available.
Proper shipping name :Not available.
Ship type Not available.
Pollution category Not available.

Section 15. Regulatory information

TSCA 5(a)2 proposed significant new use rules: 5-Chloro-2-methylisothiazolinone

SARA 313

SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet.

California Prop. 65

WARNING:  This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

International regulations

International lists Australia inventory (AICS): Not determined.

China inventory (IECSC): Not determined.

Japan inventory (ENCS): Not determined.

Japan inventory (ISHL): Not determined.

Korea inventory (KECI): Not determined.

New Zealand Inventory of Chemicals (NZIoC): Not determined.

Philippines inventory (PICCS): Not determined.

Taiwan Chemical Substances Inventory (TCSI): Not determined.

Thailand inventory: Not determined.

Turkey inventory: Not determined.

Vietnam inventory: Not determined.

 

Section 16. Other information

Hazardous Material Information System (U.S.A.)

Hazardous Material Information System

The customer is responsible for determining the PPE code for this material. For more information on HMIS®

Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc.

Procedure used to derive the classification

Classification Justification
SKIN CORROSION/IRRITATION – Category 2

SERIOUS EYE DAMAGE/ EYE IRRITATION – Category 2A

SKIN SENSITIZATION – Category 1

CARCINOGENICITY – Category 2

Calculation method

Calculation method

Calculation method

Calculation method

History

Date of printing 5/21/2020
Date of issue/Date of

Revision

5/21/2020
Date of previous issue 5/13/2020
Version 9.02
Key to abbreviations ATE = Acute Toxicity Estimate

BCF = Bioconcentration Factor

GHS = Globally Harmonized System of Classification and Labelling of Chemicals

IATA = International Air Transport Association

IBC = Intermediate Bulk Container

IMDG = International Maritime Dangerous Goods

LogPow = logarithm of the octanol/water partition coefficient

MARPOL = International Convention for the Prevention of Pollution From Ships, 1973

as modified by the Protocol of 1978. (“Marpol” = marine pollution)

N/A = Not available

SGG = Segregation Group

UN = United Nations

Indicates information that has changed from previously issued version.

Notice to reader

It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and any hazards associated with the product. This information is provided in good faith and believed to be accurate as of the effective date herein. However, no warranty, express or implied, is given. The information presented here applies only to the product as shipped. The addition of any material can change the composition, hazards and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer,  or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user should not use the product for any purpose other than the purpose shown in the applicable section of this SDS without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other source.

Date of issue/Date of revision : 5/21/2020

Date of previous issue : 5/13/2020

Version : 9.02 13/13

KSRV08120 KOOL SEAL® RV Elastomeric Base Coat

SHW-85-NA-GHS-US

File Downloads

Instruction Manual
Safety Data Sheet, KSRV08120
Download [optimized]
Download

References

Leave a comment

Your email address will not be published.