Instruction Manual for KOOL SEAL models including: Safety Data Sheet, KSRV08120
5/21/2020. Date of previous issue. : 5/13/2020. Version. : 9.02. 1/13 ... Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
Kool Seal KSRV08120-16 Elastomeric RV Base Coat - 1 Gallon
File Info : application/pdf, 13 Pages, 138.38KB
DocumentDocumentSAFETY DATA SHEET
KSRV08120
Section 1. Identification
Product name
: KOOL SEAL® RV Elastomeric Base Coat
Product code
: KSRV08120
Other means of identification
Product type
: Not available. : Liquid.
Relevant identified uses of the substance or mixture and uses advised against
Paint or paint related material.
Manufacturer
: KST Coatings A Business Unit of the Sherwin-Williams Co.
101 W. Prospect Avenue
Cleveland, OH 44115
Emergency telephone number of the company
Product Information Telephone Number
: US / Canada: (216) 566-2917 Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year
: US / Canada: (888) 321-5665 Mexico: Not Available
Regulatory Information Telephone Number
: US / Canada: (216) 566-2902 Mexico: Not Available
Transportation Emergency : US / Canada: (216) 566-2917
Telephone Number
Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year
Section 2. Hazards identification
OSHA/HCS status
Classification of the substance or mixture
: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
: SKIN CORROSION/IRRITATION - Category 2 SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A SKIN SENSITIZATION - Category 1 CARCINOGENICITY - Category 2
GHS label elements
Hazard pictograms
:
Signal word Hazard statements
Precautionary statements General
: Warning : Causes serious eye irritation.
Causes skin irritation. May cause an allergic skin reaction. Suspected of causing cancer.
: Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
1/13
SHW-85-NA-GHS-US
Section 2. Hazards identification
Prevention
Response
Storage Disposal Supplemental label elements
: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves. Wear eye or face protection. Wear protective clothing. Avoid breathing vapor. Wash hands thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace.
: IF exposed or concerned: Get medical attention. IF ON SKIN: Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get medical attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
: Store locked up.
: Dispose of contents and container in accordance with all local, regional, national and international regulations.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Please refer to the SDS for additional information. Keep out of reach of children. Do not transfer contents to other containers for storage.
Hazards not otherwise classified
: None known.
Section 3. Composition/information on ingredients
Substance/mixture
Other means of identification
: Mixture : Not available.
CAS number/other identifiers
Ingredient name
Calcium Carbonate Titanium Dioxide Heavy Paraffinic Oil Light Aliphatic Hydrocarbon 1,2,4-Trimethylbenzene Light Aromatic Hydrocarbons 1,3,5-Triazine-triethanol
% by weight
10 - <20 3 1 <1 0.3 0.3 0.3
CAS number
1317-65-3 13463-67-7 64742-65-0 64742-47-8 95-63-6 64742-95-6 4719-04-4
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health and hence require reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.
Section 4. First aid measures
Description of necessary first aid measures
Eye contact
: Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Inhalation
: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
2/13
SHW-85-NA-GHS-US
Section 4. First aid measures
Skin contact Ingestion
: Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. In the event of any complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean shoes thoroughly before reuse.
: Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact
: Causes serious eye irritation.
Inhalation
: No known significant effects or critical hazards.
Skin contact
: Causes skin irritation. May cause an allergic skin reaction.
Ingestion
: No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact
: Adverse symptoms may include the following: pain or irritation
watering
redness
Inhalation
: No specific data.
Skin contact
: Adverse symptoms may include the following: irritation
redness
Ingestion
: No specific data.
Indication of immediate medical attention and special treatment needed, if necessary
Notes to physician
: Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Specific treatments
: No specific treatment.
Protection of first-aiders
: No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
See toxicological information (Section 11)
Section 5. Fire-fighting measures
Extinguishing media
Suitable extinguishing media
Unsuitable extinguishing media
: Use an extinguishing agent suitable for the surrounding fire. : None known.
Specific hazards arising from the chemical
: In a fire or if heated, a pressure increase will occur and the container may burst.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
3/13
SHW-85-NA-GHS-US
Section 5. Fire-fighting measures
Hazardous thermal decomposition products
: Decomposition products may include the following materials: carbon dioxide
carbon monoxide
metal oxide/oxides
Special protective actions for fire-fighters
Special protective equipment for fire-fighters
: Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.
: Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Section 6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
For non-emergency personnel
: No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Environmental precautions
: Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Methods and materials for containment and cleaning up
Small spill
: Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and
place in an appropriate waste disposal container. Dispose of via a licensed waste
disposal contractor.
Large spill
: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Section 7. Handling and storage
Precautions for safe handling
Protective measures
: Put on appropriate personal protective equipment (see Section 8). Persons with a history of skin sensitization problems should not be employed in any process in which this product is used. Avoid exposure - obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not ingest. Avoid breathing vapor or mist. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
4/13
SHW-85-NA-GHS-US
Section 7. Handling and storage
Advice on general occupational hygiene
: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.
Conditions for safe storage, including any incompatibilities
: Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.
Section 8. Exposure controls/personal protection
Control parameters Occupational exposure limits (OSHA United States)
Ingredient name Calcium Carbonate
Titanium Dioxide Heavy Paraffinic Oil
Light Aliphatic Hydrocarbon 1,2,4-Trimethylbenzene
Light Aromatic Hydrocarbons 1,3,5-Triazine-triethanol
CAS # 1317-65-3
13463-67-7 64742-65-0
64742-47-8 95-63-6
64742-95-6 4719-04-4
Exposure limits
OSHA PEL (United States, 5/2018). TWA: 5 mg/m³ 8 hours. Form: Respirable
fraction TWA: 15 mg/m³ 8 hours. Form: Total dust
NIOSH REL (United States, 10/2016). TWA: 5 mg/m³ 10 hours. Form: Respirable
fraction TWA: 10 mg/m³ 10 hours. Form: Total
ACGIH TLV (United States, 3/2019). TWA: 10 mg/m³ 8 hours.
OSHA PEL (United States, 5/2018). TWA: 15 mg/m³ 8 hours. Form: Total dust
OSHA PEL (United States, 5/2018). TWA: 5 mg/m³ 8 hours.
ACGIH TLV (United States, 3/2019). TWA: 5 mg/m³ 8 hours. Form: Inhalable
fraction NIOSH REL (United States, 10/2016).
TWA: 5 mg/m³ 10 hours. Form: Mist STEL: 10 mg/m³ 15 minutes. Form: Mist
ACGIH TLV (United States, 3/2019). Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon vapor) 8 hours. ACGIH TLV (United States, 3/2019).
TWA: 25 ppm 8 hours. TWA: 123 mg/m³ 8 hours. NIOSH REL (United States, 10/2016). TWA: 25 ppm 10 hours. TWA: 125 mg/m³ 10 hours.
None. None.
Occupational exposure limits (Canada)
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
5/13
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Ingredient name
CAS #
Exposure limits
Titanium dioxide
13463-67-7
CA British Columbia Provincial (Canada, 5/2019).
TWA: 3 mg/m³ 8 hours. Form: Respirable dust
TWA: 10 mg/m³ 8 hours. Form: Total dust CA Quebec Provincial (Canada, 1/2014).
TWAEV: 10 mg/m³ 8 hours. Form: Total dust. CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 10 mg/m³ 8 hours. CA Ontario Provincial (Canada, 1/2018).
TWA: 10 mg/m³ 8 hours. CA Saskatchewan Provincial (Canada, 7/2013).
STEL: 20 mg/m³ 15 minutes. TWA: 10 mg/m³ 8 hours.
Occupational exposure limits (Mexico)
CAS #
Exposure limits
None.
Appropriate engineering controls
Environmental exposure controls
: If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.
: Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.
Individual protection measures
Hygiene measures
: Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.
Eye/face protection
: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Skin protection
Hand protection
: Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.
Body protection
: Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before
handling this product.
Other skin protection
: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
6/13
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Respiratory protection
: Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Section 9. Physical and chemical properties
Appearance Physical state Color
Odor Odor threshold pH Melting point/freezing point Boiling point/boiling range Flash point Evaporation rate Flammability (solid, gas) Lower and upper explosive (flammable) limits Vapor pressure Vapor density Relative density Solubility Partition coefficient: noctanol/water Auto-ignition temperature Decomposition temperature Viscosity Molecular weight Aerosol product
Heat of combustion
: Liquid. : Not available. : Not available. : Not available. :9 : Not available. : 100°C (212°F) : Closed cup: Not applicable. : 0.09 (butyl acetate = 1) : Not available. : Not available.
: 2.3 kPa (17.5 mm Hg) [at 20°C] : 1 [Air = 1] : 1.16 : Not available. : Not available.
: Not available. : Not available. : Kinematic (40°C (104°F)): >0.205 cm2/s (>20.5 cSt) : Not applicable.
: 0.861 kJ/g
Section 10. Stability and reactivity
Reactivity
: No specific test data related to reactivity available for this product or its ingredients.
Chemical stability
: The product is stable.
Possibility of hazardous reactions
: Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to avoid
: No specific data.
Incompatible materials
: No specific data.
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should
products
not be produced.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
7/13
SHW-85-NA-GHS-US
Section 11. Toxicological information
Information on toxicological effects Acute toxicity
Product/ingredient name Result
Heavy Paraffinic Oil
1,2,4-Trimethylbenzene
Light Aromatic Hydrocarbons 1,3,5-Triazine-triethanol
LD50 Dermal
LD50 Oral LC50 Inhalation Vapor LD50 Oral LD50 Oral LD50 Oral
Irritation/Corrosion
Product/ingredient name Result
Titanium Dioxide
Skin - Mild irritant
Light Aromatic Hydrocarbons Eyes - Mild irritant
Species
Rabbit Rat Rat Rat Rat Rat
Dose
>5000 mg/kg >5000 mg/kg 18000 mg/m³ 5 g/kg 8400 mg/kg 763 mg/kg
Exposure
4 hours -
Species Human
Rabbit
Score -
-
Exposure
72 hours 300 ug I 24 hours 100 Ul
Observation -
-
Sensitization Not available.
Mutagenicity Not available.
Carcinogenicity Not available.
Classification Product/ingredient name Titanium Dioxide
OSHA -
IARC 2B
NTP -
Reproductive toxicity Not available.
Teratogenicity Not available.
Specific target organ toxicity (single exposure) Name Calcium Carbonate Light Aliphatic Hydrocarbon
1,2,4-Trimethylbenzene Light Aromatic Hydrocarbons
Specific target organ toxicity (repeated exposure)
Category
Category 3
Category 3 Category 3
Category 3
Category 3 Category 3
Route of exposure Not applicable.
Not applicable. Not applicable.
Not applicable.
Not applicable. Not applicable.
Target organs
Respiratory tract irritation Narcotic effects Respiratory tract irritation Respiratory tract irritation Narcotic effects Respiratory tract irritation
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
8/13
SHW-85-NA-GHS-US
Section 11. Toxicological information
Name
Light Aliphatic Hydrocarbon Light Aromatic Hydrocarbons 1,3,5-Triazine-triethanol
Aspiration hazard
Name Heavy Paraffinic Oil Light Aliphatic Hydrocarbon 1,2,4-Trimethylbenzene Light Aromatic Hydrocarbons
Category
Category 2 Category 2 Category 1
Route of exposure
Not determined Not determined Not determined
Target organs
Not determined Not determined Not determined
Result
ASPIRATION HAZARD - Category 1 ASPIRATION HAZARD - Category 1 ASPIRATION HAZARD - Category 1 ASPIRATION HAZARD - Category 1
Information on the likely : Not available. routes of exposure
Potential acute health effects
Eye contact
: Causes serious eye irritation.
Inhalation
: No known significant effects or critical hazards.
Skin contact
: Causes skin irritation. May cause an allergic skin reaction.
Ingestion
: No known significant effects or critical hazards.
Symptoms related to the physical, chemical and toxicological characteristics
Eye contact
: Adverse symptoms may include the following: pain or irritation
watering
redness
Inhalation
: No specific data.
Skin contact
: Adverse symptoms may include the following: irritation
redness
Ingestion
: No specific data.
Delayed and immediate effects and also chronic effects from short and long term exposure
Short term exposure
Potential immediate effects
: Not available.
Potential delayed effects : Not available.
Long term exposure
Potential immediate effects
: Not available.
Potential delayed effects : Not available.
Potential chronic health effects
Not available.
General
Carcinogenicity
Mutagenicity Teratogenicity
: Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels.
: Suspected of causing cancer. Risk of cancer depends on duration and level of exposure.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
9/13
SHW-85-NA-GHS-US
Section 11. Toxicological information
Developmental effects Fertility effects
: No known significant effects or critical hazards. : No known significant effects or critical hazards.
Numerical measures of toxicity Acute toxicity estimates Not available.
Section 12. Ecological information
Toxicity
Product/ingredient name Titanium Dioxide Light Aliphatic Hydrocarbon 1,2,4-Trimethylbenzene
1,3,5-Triazine-triethanol
Result
Acute LC50 >1000000 µg/l Marine water Acute LC50 2200 µg/l Fresh water Acute LC50 4910 µg/l Marine water
Acute LC50 7720 µg/l Fresh water Acute EC50 26.1 ppm Fresh water Acute LC50 39 ppm Fresh water
Species
Fish - Fundulus heteroclitus Fish - Lepomis macrochirus Crustaceans - Elasmopus pectenicrus - Adult Fish - Pimephales promelas Daphnia - Daphnia magna Fish - Lepomis macrochirus
Exposure
96 hours 4 days 48 hours
96 hours 48 hours 96 hours
Persistence and degradability Product/ingredient name Aquatic half-life Light Aromatic Hydrocarbons -
Photolysis -
Biodegradability Readily
Bioaccumulative potential
Product/ingredient name LogPow
1,2,4-Trimethylbenzene
-
Light Aromatic Hydrocarbons -
BCF
243 10 to 2500
Potential
low high
Mobility in soil
Soil/water partition coefficient (KOC)
: Not available.
Other adverse effects
: No known significant effects or critical hazards.
Section 13. Disposal considerations
Disposal methods
: The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
10/13
SHW-85-NA-GHS-US
Section 14. Transport information
UN number
DOT Classification
Not regulated.
TDG Classification
Not regulated.
Mexico Classification
Not regulated.
IATA Not regulated.
UN proper
-
shipping name
Transport
-
hazard class(es)
-
-
-
-
-
-
IMDG Not regulated. -
Packing group -
Environmental No. hazards
Additional
-
information
-
-
-
-
No.
No.
No.
No.
-
-
-
-
Special precautions for user : Multi-modal shipping descriptions are provided for informational purposes and do not consider container sizes. The presence of a shipping description for a particular mode of transport (sea, air, etc.), does not indicate that the product is packaged suitably for that mode of transport. All packaging must be reviewed for suitability prior to shipment, and compliance with the applicable regulations is the sole responsibility of the person offering the product for transport. People loading and unloading dangerous goods must be trained on all of the risks deriving from the substances and on all actions in case of emergency situations.
Transport in bulk according : Not available. to Annex II of MARPOL and the IBC Code
Proper shipping name Ship type Pollution category
: Not available. : Not available. : Not available.
Section 15. Regulatory information
TSCA 5(a)2 proposed significant new use rules: 5-Chloro-2-methylisothiazolinone SARA 313 SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet.
California Prop. 65 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
International regulations
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
11/13
SHW-85-NA-GHS-US
Section 15. Regulatory information
International lists
: Australia inventory (AICS): Not determined. China inventory (IECSC): Not determined. Japan inventory (ENCS): Not determined. Japan inventory (ISHL): Not determined. Korea inventory (KECI): Not determined. New Zealand Inventory of Chemicals (NZIoC): Not determined. Philippines inventory (PICCS): Not determined. Taiwan Chemical Substances Inventory (TCSI): Not determined. Thailand inventory: Not determined. Turkey inventory: Not determined. Vietnam inventory: Not determined.
Section 16. Other information
Hazardous Material Information System (U.S.A.)
Health
*3
Flammability
0
Physical hazards
0
The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc.
Procedure used to derive the classification
Classification
SKIN CORROSION/IRRITATION - Category 2 SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A SKIN SENSITIZATION - Category 1 CARCINOGENICITY - Category 2
Justification
Calculation method Calculation method Calculation method Calculation method
History
Date of printing
: 5/21/2020
Date of issue/Date of revision
: 5/21/2020
Date of previous issue
: 5/13/2020
Version
: 9.02
Key to abbreviations
: ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group UN = United Nations
Indicates information that has changed from previously issued version.
Notice to reader
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
12/13
SHW-85-NA-GHS-US
Section 16. Other information
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and any hazards associated with the product. This information is provided in good faith and believed to be accurate as of the effective date herein. However, no warranty, express or implied, is given. The information presented here applies only to the product as shipped. The addition of any material can change the composition, hazards and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer, or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user should not use the product for any purpose other than the purpose shown in the applicable section of this SDS without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other source.
Date of issue/Date of revision
: 5/21/2020 Date of previous issue
KSRV08120
KOOL SEAL® RV Elastomeric Base Coat
: 5/13/2020
Version : 9.02
13/13
SHW-85-NA-GHS-US
DynaPDF 3.0.32.82