KONICA MINOLTA Reflection 2 Mini D5 PWM D-RGB Mini Distro Plate Strix
BOX CONTENTS
DISTRIBUTION PLATE DIMENSIONS
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
| Position | EAN | Description | Quantity |
| 1 | 105063 | Bottom plexi plate | 1 |
| 2 | 105064 | Top plexi plate | 1 |
| 3 | 105067 | LED Cover (Black e.) | 1 |
| 4 | 100663 | EK – Badge | 1 |
| 5 | 5154 | OR 52 x 3 mm | 1 |
| 6 | 3831109837597 | D5 Pump | 1 |
| 7 | 101803 | Pump cover (Acetal) | 1 |
| 8 | 8311 | Screw M4 x 20 DIN7984 | 4 |
| 9 | 8312 | Screw M4 x 16 DIN7991 | 49 |
| 10 | 104642 | Left Mount (Black E.) | 1 |
| 11 | 9061 | Screw M3 x 25 DIN7991 | 6 |
| 12 | 104599 | Mylar – Reflection2 | 2 |
| 13 | 102639 | EK – Plug G1/4 | 10 |
| 14 | SET | OR SET | 1 |
| 15 | 100815 | LED D-RGB strip 500/400 mm | 1 |
| 16 | 3831109834282 | Plug Cover (Black) | 10 |
PREPARING THE O11D Mini CHASSIS
Before installing the distribution plate, carefully read the PC case manual.
STEP 1
Unscrew the factory provided screws and remove the top panel from the case.
STEP 2
Remove side and the front panel from the case.
INSTALLING THE DISTRIBUTION PLATE
STEP 1
Carefully place the EK-Quantum Reflection2 PC-O11D Mini D5 PWM D-RGB distribution plate into the PC case and align the mounting holes.
STEP 2
Secure the distribution plate to the chassis with eight (8) M4 x 8 DIN7991 screws (as shown in the diagram).
For this step you will need:
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
It is mandatory to use at least one of each type of port and all remaining ports should be sealed using the supplied plugs. The EK-Loop Multi Allen Key may be used to install all EK fittings, do not use excessive force. If one of the prescribed components will not be installed (ie. bottom radiator or GPU block) then one IN and one OUT port must still be joined together in order for this distribution plate to function!
7-SLOT CONFIGURATION ITX / mATX / ATX
5-SLOT CONFIGURATION ITX / mATX
FLOW DIAGRAM
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground.
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
- SATA Connector: It must be connected directly to your PSU at all times as it is used to power the pump.
- 4-pin PWM fan: It can be connected to your motherboard’s CPU_ Fan or designated water pump header. It can also be connected to a controller. This cable is used to control and report the rotational speed of the pump. If it’s not connected, the pump will run at maximum speed (100% PWM).
TESTING THE LOOP
To make sure the installation of EK components was successful, we recommend you perform a leak test for 24 hours. When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. Turn on the PSU and let the pump run continuously. It is normal for the coolant level to drop during this process as air collects in the distribution plate. Inspect all parts of the loop, and in the eventuality that coolant leaks, fix the issue and repeat the testing process. Ensure that all hardware is dry before the system is powered on in order to prevent any damage.
SUPPORT AND SERVICE
In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND PRODUCT PARTS” where you can find the EAN number of each part you might need. Include the EAN number with quantity in your request.
- EKWaterBlocks
- @EKWaterBlocks
- ekwaterblocks
- EKWBofficial
- ekwaterblocks
Documents / Resources
 |
KONICA MINOLTA Reflection 2 Mini D5 PWM D-RGB Mini Distro Plate Strix [pdf] User Guide Reflection 2 Mini D5 PWM D-RGB Mini Distro Plate Strix, Reflection 2, Mini D5 PWM D-RGB Mini Distro Plate Strix, Distro Plate Strix, Plate Strix, Strix |
