User Guide for KONICA MINOLTA models including: Reflection 2 Mini D5 PWM D-RGB Mini Distro Plate Strix, Reflection 2, Mini D5 PWM D-RGB Mini Distro Plate Strix, Distro Plate Strix, Plate Strix, Strix
EK Water Blocks Quantum Line EK-Quantum Reflection² PC-O11D Mini D5 PWM D-RGB ab € 639,24 (2022) | Preisvergleich Geizhals Österreich
EKWB EK-Quantum Reflection² PC-O11D Mini D5 PWM D-RGB – Plexi
File Info : application/pdf, 16 Pages, 3.57MB
DocumentDocumentEK-Quantum Reflection2 PC-O11D Mini D5 PWM D-RGB DISTRIBUTION PLATE USER GUIDE Please note the installation of the product is intended to be undertaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance. We disclaim our liability for any damages to the product as well as incidental, consequential, or indirect damages incurred due to improper or inappropriate installation. Before you start using this product please follow these basic guidelines: Please carefully read the manual before beginning with the installation process! The EK Fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets. The use of quality market-proven corrosion-inhibiting coolants is always strongly recommended for any liquid cooling system. Do not use pure distilled water as a cooling liquid! For best results, EK recommends the use of EK-CryoFuel Coolants. TABLE OF CONTENTS BOX CONTENTS 4 DISTRIBUTION PLATE DIMENSIONS 5 TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6 PREPARING THE O11D Mini CHASSIS 7 INSTALLING THE DISTRIBUTION PLATE 8 RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 9 7-SLOT CONFIGURATION 9 5-SLOT CONFIGURATION 11 FLOW DIAGRAM 13 CONNECTING THE D-RGB LED STRIP 14 CONNECTING THE PUMP 14 TESTING THE LOOP 15 SUPPORT AND SERVICE 16 SOCIAL MEDIA 16 - 3 - BOX CONTENTS 8 EK-Quantum Reflection2 PC-O11D Mini D5 PWM D-RGB - 4 - M4 x 8 7991DIN (8 pcs) Allen Key 2.5 mm (1 pc) EK-Loop Multi Allen Key DISTRIBUTION PLATE DIMENSIONS 206 mm 189.5 mm 332 mm 302.5 mm 230.5 mm - 5 - 8 mm 30.5 mm 76 mm TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 8 7 6 5 1 15 2 4 16 13 3 14 11 Technical Specification: Dimensions with the attached pump (H x W x D): 332 x 206 x 76 mm D-RGB LED count: 12 D-RGB cable length: 500 mm D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 EAN 105063 105064 105067 100663 5154 3831109837597 101803 8311 8312 104642 9061 104599 102639 SET 100815 3831109834282 Description Bottom plexi plate Top plexi plate LED Cover (Black e.) EK - Badge OR 52 x 3 mm D5 Pump Pump cover (Acetal) Screw M4 x 20 DIN7984 Screw M4 x 16 DIN7991 Left Mount (Black E.) Screw M3 x 25 DIN7991 Mylar - Reflection2 EK - Plug G1/4 OR SET LED D-RGB strip 500/400 mm Plug Cover (Black) Quantity 1 1 1 1 1 1 1 4 49 1 6 2 10 1 1 10 9 9 10 11 12 - 6 - PREPARING THE O11D Mini CHASSIS Before installing the distribution plate, carefully read the PC case manual. STEP 1 Unscrew the factory provided screws and remove the top panel from the case. FACTORY PROVIDED SCREWS STEP 1 STEP 2 Remove side and the front panel from the case. STEP 2 - 7 - INSTALLING THE DISTRIBUTION PLATE STEP 1 Carefully place the EK-Quantum Reflection2 PC-O11D Mini D5 PWM D-RGB distribution plate into the PC case and align the mounting holes. STEP 1 M4 x 8 7991DIN SCREW STEP 2 Secure the distribution plate to the chassis with eight (8) M4 x 8 DIN7991 screws (as shown in the diagram). For this step you will need: Allen Key 2.5 mm M4 x 8 7991DIN (8 pcs) 8 STEP 2 - 8 - RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS PLUG RADIATOR 2 OUT RADIATOR 2 IN CPU OUT CPU IN GPU IN/OUT (SLOT 1) GPU IN/OUT (SLOT 2) GPU IN/OUT (SLOT 3) GPU IN (SLOT 2) GPU IN (SLOT 3) DRAIN RADIATOR 1 OUT It is mandatory to use at least one of each type of port and all remaining ports should be sealed using the supplied plugs. The EK-Loop Multi Allen Key may be used to install all EK fittings, do not use excessive force. If one of the prescribed components will not be installed (ie. bottom radiator or GPU block) then one IN and one OUT port must still be joined together in order for this distribution plate to function! 7-SLOT CONFIGURATION ITX / mATX / ATX RADIATOR 2 Up to S240 (side) RADIATOR 1 Up to S360 (bottom) RADIATOR 1 IN - 9 - RADIATOR 2 Up to S240 (side) FILL (EXTERIOR) DRAIN (EXTERIOR) RADIATOR 1 Up to S360 (bottom) - 10 - RADIATOR 2 (Optional) Up to S240 (side) RADIATOR 3 (Optional) Up to S360 (top) RADIATOR 2 OUT RADIATOR 2 IN CPU OUT 5-SLOT CONFIGURATION ITX / mATX CPU IN GPU IN/OUT (SLOT 1) RADIATOR 1 Up to S360 (bottom) DRAIN RADIATOR 1 OUT RADIATOR 1 IN - 11 - RADIATOR 2 (Optional) Up to S240 (side) RADIATOR 3 (Optional) Up to S360 (top) FILL (EXTERIOR) DRAIN (EXTERIOR) RADIATOR 1 Up to S360 (bottom) - 12 - FLOW DIAGRAM - 13 - CONNECTING THE D-RGB LED STRIP Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground. D-RGB Header RGB Header CONNECTING THE PUMP SATA CONNECTOR 4-PIN PWM FAN CONNECTOR The EK-D5 PWM pump has two connectors. 1. SATA Connector: It must be connected directly to your PSU at all times as it is used to power the pump. 2. 4-pin PWM fan: It can be connected to your motherboard's CPU_ Fan or designated water pump header. It can also be connected to a controller. This cable is used to control and report the rotational speed of the pump. If it's not connected, the pump will run at maximum speed (100% PWM). - 14 - TESTING THE LOOP To make sure the installation of EK components was successful, we recommend you perform a leak test for 24 hours. When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. Turn on the PSU and let the pump run continuously. It is normal for the coolant level to drop during this process as air collects in the distribution plate. Inspect all parts of the loop, and in the eventuality that coolant leaks, fix the issue and repeat the testing process. Ensure that all hardware is dry before the system is powered on in order to prevent any damage. - 15 - SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with "TECHNICAL SPECIFICATIONS AND PRODUCT PARTS" where you can find the EAN number of each part you might need. Include the EAN number with quantity in your request. SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks