CRAVOT MagRack F2 Hitch Bike Rack

Introduction

This manual provides essential information for the assembly, adjustment, and safe use of the CRAVOT MagRack F2 hitch bike rack. Please read thoroughly before assembly and use.

CRAVOT is committed to delivering a properly assembled and accurately adjusted bike rack. For inquiries after reviewing this manual, please reach out to the Help Center. Our customer service team is ready to address questions regarding assembly, performance, operation, service parts, or general services.

Keep this manual for future reference. Information is subject to change as products are refined. Pay special attention to warnings, cautions, and notices marked with symbols or specific labels.

Parts List

Visual representation of the parts: Part 1 is the main base combination. Part 2 are connecting blocks. Part 3 are straps for securing bikes. Part 4 is the pin lock assembly.

Installation Instructions

Step 1: Loosen and Eject Nut

Rotate the red plastic wrench at the indicated position counterclockwise to loosen it, then push in the direction of the arrow [arrow] to eject the nut on the other side from the slide slot.

[Diagram Description: Illustration shows a red plastic wrench being rotated counterclockwise to loosen a component. It is then pushed in the direction of an arrow to eject a nut from a slide slot.]

Step 2: Extend Support Rod

Extend the support rod in the direction of the arrow [arrow].

[Diagram Description: Illustration shows a support rod being extended outwards, indicated by an arrow.]

Step 3: Tighten Nut

Pull the red plastic wrench at the indicated position, ensure the nut side aligns and enters the slot, then rotate the wrench clockwise to tighten.

[Diagram Description: Illustration shows a red plastic wrench being pulled. The nut is aligned to enter a slot, and the wrench is rotated clockwise to tighten it.]

Step 4: Adjust Wheel Holders

Adjust the Wheel Holder's position as shown in the diagram, ensuring it is positioned on the left and right sides.

[Diagram Description: Illustration demonstrates adjusting the position of the wheel holders on the rack, specifying placement on the left and right sides.]

Step 5: Install Connecting Block

Install the Connecting Block (2), then press the button to adjust the position up or down. Note: When installing the connecting block, the button must be placed in the sawtooth [sawtooth] position, otherwise it cannot be fixed.

[Diagram Description: Illustration shows a connecting block being installed. A button on the block allows for up/down adjustment. A note emphasizes that the button must be engaged in the sawtooth position for secure fixing.]

Step 6: Insert into Vehicle Receiver

Insert the Bike Rack into the vehicle's 2" receiver, then insert the pin to secure it.

[Diagram Description: Illustration shows the bike rack's hitch being inserted into a vehicle's 2-inch receiver. A pin is then inserted through both the rack and receiver to secure the assembly.]

Folding Steps

Step 1: Fold Tire Bracket

The tire bracket can be folded when the frame is unloaded. Warning: Please ensure it is locked, otherwise it may cause product damage or even affect personal safety.

[Diagram Description: Illustration shows the tire bracket being folded. A warning symbol is present, emphasizing the need to ensure it is locked to prevent damage or safety issues.]

How to Use the Strap

Step 1: Secure Wheels

Use the strap to secure the wheel to the rear support rod of the tire bracket to ensure the tire is firmly fastened during transit. Place the tire into the tire bracket and secure both the front and rear wheels with the strap.

[Diagram Description: Illustration shows straps being used to secure a bicycle wheel to the rear support rod of the tire bracket. Another illustration depicts a tire placed in the bracket and secured with straps.]

Warning: The connecting block can only be fixed on the top tube or seat tube of the bicycle. It is prohibited to attach it to the down tube or any other position, as this may cause product damage or even pose a safety risk.

Bike Installation Instructions

Place the tire into the tire bracket and secure both the front and rear wheels with the strap.

[Diagram Description: Three diagrams illustrate bicycle mounting. The first two show correct installation with green checkmarks (✔️). The third shows an incorrect installation with a red cross mark (❌), accompanied by a warning about placement.]

Correct Installation: Bikes are mounted securely, with wheels and frame properly attached.

Incorrect Installation Warning: Attaching the connecting block to the down tube or other positions may cause damage or safety risks.

Dimensions

[Diagram Description: Diagram of the bike rack displaying its dimensions: 52.7 inches (length), 35.4 inches (height), and 29 inches (width).]

• Length: 52.7"
• Height: 35.4"
• Width: 29"

Technical Specifications

• Maximum Load: Bikes under 150 LBS
• Maximum bike wheelbase: 51"
• Applicable Types of Hitched Bike: Electric Bike/Regular Bike
• Not intended for use with mopeds, motorcycles or 3-wheel bikes
• Applicable for tires width within 3.5"

Warnings

• Do not overload beyond the bike rack's weight capacity of 150lbs.
• Do not carry more than 2 bikes on the carrier.
• The bike rack is not intended for transporting humans or animals.
• If planning to load only one bike, place it in the position closest to the vehicle.
• All bikes must be secured properly before operating the vehicle.
• Ensure the front of the bike(s), when mounted, are at or above the bottom of the bumper to avoid damage.
• Do not carry flammable items on the bike rack.
• If transporting electric bikes, remove the batteries prior to transport to reduce carrier weight.
• During long trips, frequently check straps and bike position, especially on rough terrain.
• Do not make alterations to the product.
• Failure to heed warnings may result in personal injury and/or property damage.
• Inspect the bike rack for wear, corrosion, and fatigue before each use. Do not use if parts are bent, broken, deformed, or missing.

CRAVOT Warranty Policy

CRAVOT provides a Limited Warranty for its products. This product is covered by a 1-year warranty from the date of purchase. The duration of the warranty varies based on the product category and manufacturing standards. Specific warranty details for your product can be found in the product manual or on our website.

Warranty Coverage: Covers defects in materials and workmanship under normal use. Proof of purchase is required to validate warranty claims.

Exclusions from Warranty: Damages from improper use, accidents, unauthorized repairs/modifications, or normal wear and tear are not covered. Products outside of the warranty period or damages not covered can be repaired at a reasonable cost if applicable (Determined by CRAVOT).

Claiming Warranty Service: To claim warranty service, please contact customer service with your proof of purchase and a description of the issue. Our customer service team will guide you through the warranty process.

Repair/Replacement Policy: Qualifying products damaged by non-human factors will be repaired or replaced free of charge within the warranty period. Replacement products or parts may be new or refurbished but will function like new.

State Law Considerations: This warranty grants specific legal rights, and you may also have other rights which vary from state to state in the United States. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

Disclaimer of Liability: It is crucial to follow the instructions provided in the product manual for proper use. CRAVOT is not responsible for any damages or losses resulting from improper operation or handling of the product. This disclaimer includes but is not limited to personal injury, damage to property, or any other losses incurred due to non-compliance. The warranty does not apply to the product when resold as a second-hand item.

Customer Support

CRAVOT's customer support team is always ready to assist with any questions or concerns regarding their products or services. Please contact them through the provided contact methods.

Contact methods:

• Website: cravot.com
• Email: support@cravot.com

Thank you for your support and trust in CRAVOT. We are committed to delivering high-quality products and ensuring your satisfaction with our services.

[Diagram Description: A section labeled "Get Support" with contact information is visually represented.]