DIGI TM-B3SENSOR Smart Sense B3 Sensor
Use these instructions to add a SmartSense B3 Sensor to an existing SmartSense environment.
ការដំឡើងឧបករណ៍ចាប់សញ្ញា B3
Your SmartSense B3 Sensor arrives powered off.
- Hold the power button for 2-5 seconds, then release to turn on the B3 Sensor.
- Both the green and red LEDs will simultaneously blink twice to indicate the sensor is on and will report at a scheduled interval (under normal operation, these are the only times the LEDs will illuminate).
- To check the status of a B3 Sensor, press the power button once. A green LED indicates the sensor is on, while a red LED indicates that the sensor is in Hibernation Mode (not collecting or sending data).**
- SmartSense recommends installing the sensor according to the FDA Food Code, placing it “in a location that is representative of the actual storage temperature of the unit,” away from any compressors or fans.
- ប្រើខ្សែ zip ដែលរួមបញ្ចូលដើម្បីភ្ជាប់ឧបករណ៍ចាប់សញ្ញា B3 ។ ខ្សែរ៉ូតគួរតែត្រូវបានភ្ជាប់តាមរយៈរង្វិលជុំម៉ោននៅផ្នែកខាងលើនៃឧបករណ៍ចាប់សញ្ញា ហើយភ្ជាប់ដោយសុវត្ថិភាពទៅនឹងចំណុចម៉ោន ដើម្បីឱ្យឧបករណ៍ចាប់សញ្ញាព្យួរបញ្ឈរ ហើយបែរមុខទៅទ្វារនៃករណីរបស់អ្នក។
- If a suitable mounting point does not exist, contact SmartSense Support for additional mounting options.
Once turned on, the B3 Sensor may be placed back into Hibernation Mode if not in use. To place the sensor into Hibernation Mode, hold the power button down for about 5 seconds (until the green and red LEDs simultaneously blink 3 times), release the button, and hold the button again for 2-5 seconds within 20 seconds to confirm Hibernation Mode is activated (a single red LED flash will confirm the device is back in Hibernation Mode). You can press the power button again to confirm the B3 Sensor is in Hibernation Mode (the red LED will flash once).
ចំណាំ
When you put the B3 Sensor in Hibernation Mode, the device cannot be re-enabled for one minute to allow for proper shutdown; all stored data will be deleted, and the device will revert to its default configuration.
ការប្រុងប្រយ័ត្ន
Risk of fire and burns. Do not recharge, disassemble, heat above (manufacturer’s specified temperature), or incinerate. Keep the battery out of reach of children and in its original package until ready to use. Dispose of used batteries promptly.
ផ្ទៀងផ្ទាត់ឧបករណ៍ចាប់សញ្ញា B3 កំពុងរាយការណ៍
បញ្ជាក់ថាឧបករណ៍ចាប់សញ្ញា B3 កំពុងទំនាក់ទំនងជាមួយផ្ទាំងគ្រប់គ្រង SmartSense របស់អ្នក។ ប្រសិនបើអ្នកមិនមានការចូលដោយប្រើ Super Admin ឬការអនុញ្ញាតពីអ្នកគ្រប់គ្រងទេ សូមសួរមិត្តរួមការងារឱ្យធ្វើការត្រួតពិនិត្យនេះ។ អ្នកនឹងត្រូវចូលទៅ SmartSense Web កម្មវិធី
- បើក ក web browser and navigate to app.smartsense.co.
- Enter your credentials (username and password), then select LOG IN.
- At the top of the screen, click ADMI, N, then select SYSTEM MANAGEMENT.
- Click the UNASSIGNED SENSORS tab.
- នៅក្នុងរបារស្វែងរក សូមបញ្ចូលលេខសម្គាល់ឧបករណ៍នៅខាងមុខឧបករណ៍ចាប់សញ្ញា B3 (លេខសម្គាល់ឧបករណ៍ចាប់ផ្តើមដោយ "D6" ហើយការស្វែងរកតម្រូវឱ្យមានលេខសម្គាល់ឧបករណ៍ចាប់សញ្ញាពេញលេញ) ។
- When the B3 Sensor is communicating successfully, the LAST COMMUNICATION DATE column should display a recent date and time.
- This confirms that the B3 Sensor is communicating as expected.
ការណែនាំអំពីការដំឡើង
- Ambient Sensor Installation
- SmartSense Sensor Hub User Guide
- Grocery Self-Installation Guide
- Kitchen Self-Installation Guide
- Warehouse Self-Installation Guide
- Hospital and Pharmacy Self-Installation Guide
- Glycol Probe Installation
- SmartSense
- SmartTemps
- ការចេញផ្សាយថ្មី។
- Trainings & FAQs
- ឧបករណ៍ចាប់សញ្ញា
- ច្រកផ្លូវ
- ការស៊ើបអង្កេត
- ការដំឡើង
- កេរដំណែល
- តំរង់ទិស ឬផ្លាស់ប្តូរទីតាំងអង់តែនទទួល
- បង្កើនការបំបែករវាងឧបករណ៍និងអ្នកទទួល
- ភ្ជាប់ឧបករណ៍ទៅនឹងព្រីនៅលើសៀគ្វីខុសពីឧបករណ៍ទទួលត្រូវបានភ្ជាប់
- ពិគ្រោះជាមួយអ្នកចែកបៀ ឬអ្នកបច្ចេកទេសវិទ្យុ/ទូរទស្សន៍ដែលមានបទពិសោធន៍ ដើម្បីទទួលបានជំនួយ
CAN ICES-3 (B)/NMB-3 (B)
ឧបករណ៍ឌីជីថលថ្នាក់ B នេះអនុលោមតាម ICES-003 របស់កាណាដា។
សេចក្តីថ្លែងការណ៍មិនកែប្រែ
SmartSense by Digi has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment.
សេចក្តីថ្លែងការណ៍ RF Exposure
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between radiator and any part of your body. This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20 cm between the radiator and any part of your body.
អង់តែន
The B3 Sensor has been certified with a permanent, ceramic chip antenna installed on the internal circuit board. The max peak gain tested was 2.93dBi.
The following chip antennas have been considered:
- Johanson part number 2450AT18B100
- PSA-Walsin part number RFANT3216120A5T
ឯកសារ/ធនធាន
 |
DIGI TM-B3SENSOR Smart Sense B3 Sensor [pdf] សៀវភៅណែនាំរបស់ម្ចាស់ 2ATZ3-B3SENSOR, 2ATZ3B3SENSOR, TM-B3SENSOR Smart Sense B3 Sensor, TM-B3SENSOR, Smart Sense B3 Sensor, Sense B3 Sensor, B3 Sensor, Sensor |