Caddie Wheel V3 Caddy Tek 3 Wheel Golf Push Cart
CaddyTek CaddyLite 11.5 V3 Installation Guide
លក្ខណៈបច្ចេកទេស
| លក្ខណៈ | ព័ត៌មានលម្អិត |
|---|---|
| គំរូ | CaddyLite 11.5 V3 |
| សម្ភារៈ | ស៊ុមអាលុយមីញ៉ូម |
| ទម្ងន់ | 18.5 ផោន |
| វិមាត្រ | 53.5 x 27 x 45 អ៊ីញ |
ជំហានដំឡើង
Step 1: Insert the Bar
Insert the bar and line up the threaded hole with the hole in the plastic bracket.
Step 2: Align the Bar
Slide the bar until it lines up with the hole of the plastic handle.
Step 3: Secure the Bar
Thread in the screw and tighten using the Allen key.
ជំហានទី 4: ភ្ជាប់តង្កៀប
The bracket goes on this metal arm of the cart.
Step 5: Fit the Bracket
Fit the bracket between the two metal arms of the cart as shown.
Step 6: Correct Bracket Placement
This is the correct placement of the left bracket. Make sure that this part of the bracket butts up against the nut.
Step 7: Insert Zip Ties
Starting from the inside top corner, insert the zip tie. Start the other zip tie from this corner.
Step 8: Weave the Zip Tie
Weave the zip tie through the front and then back down the other side.
Step 9: Secure Zip Ties
The zip tie is weaved all the way around. This shows both zip ties weaved around, but they are only hand tight at this point.
Step 10: Tighten Zip Ties
Insert the zip tie through the small slot of the red tensioner and tighten using only the two longer arms. Once tightened, snip off the excess using the shorter arm of the tensioner. Repeat with the other zip tie and repeat everything for the right bracket.
Step 11: Use Zip Ties
Use zip ties here. The “U” Channel is a hard stop so that the bracket does not slide up during use. It is placed above the bracket as shown.
Step 12: Secure Velcro Strap
The zip tie holding the Velcro strap goes around the main post. Leave the zip tie loose and make sure that it is above the cup holder.
Step 13: Unclip the Rubber Clip
To unclip, pinch firmly the two protruding arms of the rubber clip.
Step 14: Drop in the Caddie Wheel
Drop in the Caddie Wheel between the two brackets and slide the bar to the left. Be careful when dropping in the Caddie Wheel that the right rubber clip does not get caught underneath.
Step 15: Lock the Rubber Clip
To lock, press firmly on the lower arm of the rubber clip. Make sure that it is firmly locked in. You should hear two clicks.
Step 16: Feed the Velcro Strap
Feed the Velcro strap through the slot.
Step 17: Loop the Velcro Strap
Loop the Velcro strap back up. Important: leave the strap a bit loose so that the Caddie Wheel may follow the contour of the ground.
Step 18: Start the Caddie Wheel
Showing that the Velcro strap has some slack. To start the Caddie Wheel, use the side button or just give your cart a good push if you do not want to bend down.
សំណួរគេសួរញឹកញាប់
How do I ensure the bar is securely attached?
Make sure the threaded hole lines up with the hole in the plastic bracket and tighten the screw using an Allen key.
What should I do if the bracket does not fit properly?
Ensure the bracket is placed between the two metal arms of the cart and that it butts up against the nut.
How tight should the zip ties be?
Initially, keep them hand tight, then use the tensioner to secure them firmly.
How do I start the Caddie Wheel?
Use the side button or give your cart a push to start the Caddie Wheel.
ឯកសារ/ធនធាន
 |
Caddie Wheel V3 Caddy Tek 3 Wheel Golf Push Cart [pdf] ការណែនាំអំពីការដំឡើង V3 Caddy Tek 3 Wheel Golf Push Cart, V3, Caddy Tek 3 Wheel Golf Push Cart, 3 Wheel Golf Push Cart, Golf Push Cart, Push Cart, Cart |