Kinexon KNX-ETAG1 UWB Tracking Tag with ePaper Display
Introduction
The KINEXON ePaper Tag is the Ultra-Wideband basic component for paperless material and goods handling in the industry. The ePaper solution combines high precision UWB localization technology with smart process visualization. The KINEXON ePaper Tag can be placed on workpieces and load carriers without leaving any residue to track their entire value-added process. In addition, an integrated display automatically informs about production steps that have already been completed and those that are still pending. As a result, all information is digitized, repeated and printing processes are eliminated. KINEXON ePaper solution is flexible and provides complete control and maximum flexibility for dynamic production. The combination of high-precision real-time localization and smart visualization is the key to paperless production. There are various potential use cases such as:
- ePaper-based workflow instructions for shop floor employees.
- Real-time interaction through configurable button (e.g. signal for replenishment).
- Dynamic labeling with the current status of the product or material.
- Digitization of all production & process relevant information.
Safety Information
- Read and follow all instructions before using the KINEXON ePaper Tag.
Never open the case of the KINEXON ePaper Tag. There are no user-serviceable parts or replaceable parts inside the case.
Do not use the KINEXON ePaper Tag if it has been damaged.
Use the Tag according to the following specifications. KINEXON will not take any responsibility or liability in case of accidents caused by misuse of the battery: - Stop using the device immediately and stay away from the battery if:
- The battery was exposed to high temperatures (60 °C or above).
- The battery shows signs of leakage.
- There is a noticeable odor coming from the battery. Avoid directly hitting or dropping the battery.
Disclaimer
The information in this document is subject to change without notice. KINEXON GmbH assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, contact KINEXON GmbH.
Intended Use
This manual describes the setup and use of the KINEXON ePaper Tag. Use this product only for the purpose it was designed for.
Key Facts
RF Specifications
|
RF Specifications |
|
| Positioning Principle | Real Time Location System (RTLS), Radio-based, Ultra-wideband (UWB) |
| Frequency Range | UWB (IEEE 802.15.4a):
UWB Channel 3 (4.25 – 4.75 GHz, Low Duty Cycle Interference Mitigation (LDC) according to EN 302 065-1) UWB Channel 5 (6.25 – 6.75 GHz) Average EIRP < -41 dBm / 1 MHz Peak EIRP < 0 dBm / 50 MHz |
| Update Rate | Configurable, typically 1 Hz in motion, 0.1 Hz in standstill |
| Positioning Data | 3D (x, y, z) |
| Positioning Accuracy | < 20 cm (depending on environment) |
Physical Specifications
|
Physical Specifications |
|
| Display | 4.2“, 85 x 64 mm (400×300 pixel)
2- color: black/white, display update time 3 s (25°C)
3- color: black/white/red, display update time 14 s (25°C) |
| Button | Two buttons for status and manual event trigger (event sent via RF) |
| Indicators | Two LEDs (Status and Action) |
| Accelerometer | 3-axis, +/-2 g to +/-16g, up to 200 Hz |
| Battery | Built-in 10Ah replaceable Li primary battery |
| Battery Lifetime | Up to 5 years (depending on update rate) |
| System Power | 3.0V / 200 mA |
|
Physical Specifications |
|
| Material | Acrylonitrile styrene acrylate (ASA) |
| Weight | 197g |
| Dimensions | Device only: (141 x 104.3 x 14.2) mm
Incl. holder: (168.8 x 104.3 x 24.6) mm |
Environmental Specifications
|
Environmental Specifications |
|
| Operating Temperature | 0 °C to +50 °C incl. battery |
| Storage Temperature | -20 °C to +30 °C incl. battery |
| Protection Class | IP67 |
| Regulatory Compliance (cert. ongoing) |
• FCC Part 15 subpart C • 15.250 (for indoor and outdoor use) • ETSI EN 302065-1 • ETSI EN 303883 • ETSI TS 103361 • SRRC • Draft EN 301 489 – 1, -33 • EN 61000-4-2, -4-3 • EN 62479 • 1999/519/EC • UN 38.3 • IEC 62133 |
Mechanical Drawing
Label Specifications
External Interfaces
Wireless Connection
For a wireless connection, an Ultra-Wideband (UWB) interface according to IEEE 802.15.4 standard is implemented.
Interaction Buttons
| Action Button (Upper Button) | ||
| Description | Duration | Effect |
| Short (normal) press | 150ms | Toggles alarm mode status (on or off). The content of ePaper display shown for each mode can be configured on the RIoT web interface |
| Very long press | >8s | Hardware reset |
| Status Button (Lower Button) | ||
| Description | Duration | Effect |
| Short (normal) press | 150ms | • If there is only one page configured on the RIoT web interface, the Tag refreshes the ePaper display
• If there is more than one page configured on the RIoT web interface, the Tag switches the ePaper display to the next available page • If the last page is already shown, the Tag switches the ePaper display back to the first page |
Visual LEDs
| Info LED (Left LED) | ||
| Color | Type & Duration | Explanation |
| Red | Constant, 1s | Either action or status button was pressed |
| Dynamic | Dynamic | Further info LED behavior including color & blinking duration can be configured on the RIoT web interface
|
| Power-on reset | ||
| Green | Constant, ~1s | Tag bootloader is starting |
| Yellow | Constant, ~7s | Tag in Bootloader and waiting for connection |
| Purple | Constant, duration depends on firmware size | Tag is being bootloaded with new firmware |
| Status LED (Right LED) | ||
| Color | Type & Duration | Explanation |
| Blue/Green | alternating flashing, infinite | Tag is running, the speed of flashing equals update rate of Aloha uplink |
| Blue/Red | alternating flashing, infinite | Tag is running with low battery, the speed of flashing equals update rate of Aloha uplink |
| Red | flashing, 1s | Tag is going to reset due to unrecoverable internal error detected by firmware |
Tag Battery
| A primary soft cell non-rechargeable battery is used | |
| Type | CP7839109 |
| Nominal Voltage | 3.0V |
| Capacity | 10000mAh |
| Size | (8.0 x 40.0 x 110) mm |
| Weight | 63.0g |
Hardware Variants
| Variant | Description |
| KNX-T5.1-1.1-x | ePaper Tag with non-rechargeable battery, b/w/r display |
| KNX-T5.1-1.4-x | ePaper Tag with non-rechargeable battery, b/w display |
| KNX-T5.1-4.1-x | ePaper Tag with non-rechargeable battery, b/w/r display, Bluetooth |
| KNX-T5.1-4.4-x | ePaper Tag with non-rechargeable battery, b/w display, Bluetooth |
| KNX-T5.1-2.2-x | ePaper Tag with rechargeable battery, b/w/r display |
| KNX-T5.1-2.5-x | ePaper Tag with rechargeable battery, b/w display |
| KNX-T5.1-5.2-x | ePaper Tag with rechargeable battery, b/w/r display, Bluetooth |
| KNX-T5.1-5.5-x | ePaper Tag with rechargeable battery, b/w display, Bluetooth |
Accessories
Holder
The KINEXON ePaper Tag is clipped to the holder. The holder can be mounted using the following options:
- Velcro tape: recommended width of the tape is 15mm.
- Zip-tights: maximum width of zip-tights is 15mm.
- Magnets: 18x8x4 N45 magnets hold into place with crushing ribs that can be pressed in manually.
- Screws: lateral placing using countersink screws (dmax=3.5mm, dheadmax=7.2 mm), central placing using cylinder head, pan head, button head screws (dmax=5 mm, dheadmax=9.5 mm).
Regulatory and Legal Information
The KINEXON ePaper Tag has been designed to be in compliance with both the U.S. FCC Part 15 subpart F regulations, section 15.250, and with the European Union ETSI EN 302 065 standards. Two different versions of the
KINEXON ePaper Tag are available, one version supports the FCC emissions mask (Region 1), and the second
supports the ETSI standard mask (Region 2).
FCC Compliance
This device complies with 47 CFR Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device may not be employed for the operation of toys. Operation on board an aircraft, a ship, or a satellite is prohibited. The use of this device mounted on outdoor structures, e.g., on the outside of a building or on a telephone pole, or any fixed outdoor infrastructure is prohibited. Moreover, the following statements apply: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
User information according to FCC 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation.
User information according to FCC 15.21
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body
ISED Caution
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference
- This device must accept any interference, including interference that may cause undesired operation of the device.
These devices are not permitted for operation onboard aircraft or satellites and shall also not be used for operating toys. The use of this device mounted on a fixed outdoor infrastructure, including antennas mounted on outdoor structures such as poles or buildings, is not permitted, except for operation onboard ships or land vehicles.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body.
Documents / Resources
 |
Kinexon KNX-ETAG1 UWB Tracking Tag with ePaper Display [pdf] User Manual KNX-ETAG1, KNXETAG1, 2ALC5-KNX-ETAG1, 2ALC5KNXETAG1, KNX-ETAG1 UWB Tracking Tag with ePaper Display, UWB Tracking Tag with ePaper Display |
 |
Kinexon KNX-ETAG1 UWB Tracking Tag with ePaper Display [pdf] User Manual KNX-ETAG1, KNXETAG1, 2ALC5-KNX-ETAG1, 2ALC5KNXETAG1, KNX-ETAG1 UWB Tracking Tag with ePaper Display, UWB Tracking Tag with ePaper Display |
