Kentec KS-SOLO-IN Addressable Single Input Module
Product Information
Specifications
- Ordering Code and Description: KS-SOLO-IN Addressable Single Input Module
- Operating Voltage: Loop powered
- Input Ratings: Single loop address programmed via TCH-B200
- Colour/Case Material: Compact design, Colour coded flying leads
- Approvals: LPCB approved
Product Usage Instructions
Installation
- Ensure power is disconnected before installation.
- Connect the KS-SOLO-IN module using the colour-coded flying leads for easy identification.
- Program the single loop address using the TCH-B200 programmer and PL3 programming lead.
- Install the module within third party equipment securely.
Frequently Asked Questions (FAQ)
Q: Can the KS-SOLO-IN module be used with non-addressable control panels?
A: No, the KS-SOLO-IN module is designed specifically for use with Kentec’s range of addressable control panels.
Features
Loop powered
- Single loop address programmed via TCH-B200
- Single Monitored input
- Compact design
- Colour coded flying leads for easy installation
- LPCB approved
Description
- KS-SOLO-IN is an addressable Single Input Module designed to monitor a changeover set of contacts i.e. Relay, keyswitch etc.
- A Hochiki ESP protocol device it is compatible with Kentec’s range of Taktis and Syncro Addressable control panels.
- The compact design of the enclosure enables it to be installed within third party equipment.
- KS -SOLO-IN requires a single loop address programmed via the TCH-B200 programmer and programming lead PL3.
Specification
| Specification | |
| Ordering Code and Description | KS-SOLO-IN Single Input Module |
| Operating Voltage | 17 – 41 VDC |
| Quiescent Current/ Alarm Current | 150 μA (at 41 V) |
| Input Ratings | Open Circuit >100 kΩ
Normal State ~10 kΩ (EOL resistor provided) Input Activation ~470 Ω (EOL resistor provided) Short Circuit <50 Ω |
| Operating Temperature Range | -10 °C to + 50 °C |
| Storage Temperature Range | -30 °C to + 60 °C |
| Max Humidity | 95% RH – Non Condensing (at 40 °C) |
| Colour/Case Material | Ivory / ACS |
| Weight (g) | 35 |
| Dimensions (mm) | 65 L x 42 W x 15 D |
| Approvals | LPCB approved to EN54-18:2005 |
KS-SOLO-IN panel configuration settings*
The following table details the configuration options available on the Kentec Taktis and Syncro AS control panels:
| Configuration Options | Taktis | Syncro AS/XT+ |
| Configurable location text | √ | √ |
| Map to zone | √ | √ |
| AAF – Alarm Acknowledgement Function | √ | X |
| Input Properties | Fire, Fault, Pre Alarm, Technical Alarm, Evacuate, Alert, Security, Silence, Reset, Transparent Disablement, Test Mode, Change sensitivity mode, Status, Acknowledge Alarm Extended Delay, Acknowledge Alarm Only, Override Delays | Fire, Fault, Pre Alarm, Technical Alarm, Evacuate, Alert, Security, Silence, Reset, Transparent Disablement, Test Mode |
| Input Action Message | √ | √ |
| Bypass Output Delay | √ | √ |
| Input Delay | √ | √ |
| Latching or Non-Latching | √ | √ |
| Invert input | √ | X |
* KS-SOLO-IN will be identified on Taktis and LE2 configuration software as its Hochiki equivalent part CHQ-SIM. When KS-SOLO IN is used on a Syncro AS/XT+ control panel it will be identified by the panel and the LE2 software as a CHQ-POM and must be programmed as an input device only, any configuration on the outputs will have no effect.
Documents / Resources
 |
Kentec KS-SOLO-IN Addressable Single Input Module [pdf] Owner's Manual KS-SOLO-IN Addressable Single Input Module, KS-SOLO-IN, Addressable Single Input Module, Single Input Module, Input Module, Module |
