Kentec KS-CALL-POINT-W-SCI Weatherproof Addressable Manual Call Point
Product Usage Instructions
- Mount the KS-CALL-POINT-W-SCI on a suitable surface using appropriate hardware.
- Connect the call point to the Kentec Taktis or Syncro AS control panels as per the panel configuration settings.
- Ensure the panel is powered on and functioning correctly.
- In case of an emergency, press the non-frangible element on the call point to trigger an alarm.
- Monitor the bi-colour status LED for indications of system status.
FAQ
- Q: What should I do if the bi-colour status LED does not light up?
- A: Check the power supply and connections to ensure proper functionality. If the issue persists, consult the user manual or contact customer support.
- Q: Can the KS-CALL-POINT-W-SCI be used in outdoor environments?
- A: Yes, the KS-CALL-POINT-W-SCI has an IP 67 rating, making it suitable for outdoor use and providing weatherproof protection.
- Q: How do I configure the KS-CALL-POINT-W-SCI with Kentec Taktis or Syncro AS control panels?
- A: Refer to the panel configuration settings provided in the user manual or software documentation for detailed instructions on configuration options and settings.
KS-CALL-POINT-W-SCI
Weatherproof Addressable Manual Call Point with Short-Circuit Isolator
Features
- Fast response
- Integral Short Circuit Isolator (SCI)
- Bi-colour status LED
- Non-frangible element
- Electronically addressed
- Surface mount
- Optional polling indication controlled by Kentec panel
- IP 67 rating
- LPCB approved
- Compatible with Kentec Taktis and Syncro AS control panels
Description
- KS-CALL-POINT-W-SCI is a weatherproof addressable manual call point with built-in short circuit isolator (SCI), fully compatible with Hochiki’s ESP Analogue Addressable Protocol and Kentec’s Taktis and Syncro AS product ranges.
- KS-CALL-POINT-W-SCI provides manual activation of the fire alarm system by pressing the non-frangible element. The non-frangible element provides easy activation and quick and easy reset following activation using the special test key. The test key can also be used to activate the device without pressing the frangible element.
- KS-CALL-POINT-W-SCI has an LED status indicator which provides notification of the device state i.e. Polling, Fire or SCI active. By default the LED will flash red when polling, which confirms the device is communicating with the control panel. The polling function can be turned off if required through the Kentec control panel settings – perfect for applications where a flashing LED may be a distraction such as hotel rooms, theatres etc. In a fire condition the LED will be a continuous red, if the short circuit isolator has been activated the LED will show amber.
- KS-CALL-POINT-W-SCI is provided in a red modified polyphenylene oxide surface mount housing which has an IP rating of 67, making it suitable for external use or internal areas where jetwashing is carried out. An optional hinged cover can be fitted to the KS-CALL-POINT-SCI to help deter malicious activation or prevent accidental activation.
- KS-CALL-POINT-W-SCI requires a single loop address programmed via the TCH-B200 programmer and programming lead PL3.
Specification |
|
Ordering Code and Description | KS-CALL-POINT-W-SCI Weatherproof Addressable Call Point with SCI (Red) |
Operating Voltage | 17 – 41 VDC |
Low Power Mode | 180 μA (max), 100 μA (typical) |
Quiescent Current | 350 μA (max), 250 μA (typical) |
Alarm Current | 10.0 mA (max), 5 mA (typical) |
Resistance in positive | 100 mΩ when closed (max), 100 kΩ when open (min) |
Short-circuit threshold (typical) | 430 Ω |
Transmission Method | Digital Communication Using ESP |
Operating Temperature Range | -10 °C to + 50 °C |
Storage Temperature Range | -30 °C to + 70 °C |
Max Humidity | 95% RH – Non Condensing (at 40 °C) |
Colour / Case Material | Red / Modified Polyphenylene Oxide |
Weight (g) | 234 |
Dimensions (mm) | 98 W x 94 H x 78 D |
Accessories | HINGED COVER (PS200) – Hinged cover for Call Point |
Approvals | LPCB approved to EN54-11:2001, EN54-17:2005 |
IP Rating | IP67 |
KS-CALL-POINT-W-SCI panel configuration settings*
The following table details the configuration options available on the Kentec Taktis and Syncro AS control panels:
Configuration Options | Taktis | Syncro AS/XT+ |
Configurable location text | √ | √ |
Map to zone | √ | √ |
Input Options | Fire, Fault, Pre Alarm, Technical Alarm, Evacuate, Alert, Security, Silence, Reset, Transparent, Disablement, Test Mode, Change Sensitivity Mode, Status | Fire, Fault, Pre Alarm, Technical Alarm, Evacuate, Alert, Security, Silence, Reset, Transparent, Disablement, Test Mode |
Input Action Message | √ | √ |
Bypass Output Delay | √ | √ |
Polling LED | √ | √ |
Input Delay | X | X |
Latching or Non-Latching | √** | √** |
Invert Output Operation | √ | X |
- KS-CALL-POINT-W-SCI will be identified on Taktis and LE2 configuration software as its Hochiki equivalent part HCP-E(SCI).
When KS-CALL-POINT-W-SCI is used on a Syncro AS/XT+ control panel it will be identified by the panel as the Hochiki part HCPE and the LE2 software as an MCP-E/HCP-E - Dependent on Input Action.
Datasheet DS218 06/24 Rev.01
For further information visit www.kentec.co.uk
Kentec Electronics Ltd. reserves the right to alter the specification of its products from time to time without notice. Although every effort has been made to ensure the accuracy of the information contained in this document it is not warranted or represented by Kentec Electronics Ltd. to be a complete and up-to-date description.
Documents / Resources
![]() |
Kentec KS-CALL-POINT-W-SCI Weatherproof Addressable Manual Call Point [pdf] Owner's Manual KS-CALL-POINT-W-SCI Weatherproof Addressable Manual Call Point, KS-CALL-POINT-W-SCI, Weatherproof Addressable Manual Call Point, Addressable Manual Call Point, Manual Call Point, Call Point, Point |