Keeson RF304 Adjustable Bed Remote Control User Manual

Keeson RF304 Adjustable Bed Remote Control

Specifications

• Product Name: REMOTE CONTROL
• Model: RC304C
• Input: 3 x Battery AAA 1.5V
• Manufacturer: Keeson Technology Corporation Limited
• Manufacturing Country: China

Button Function

USING INSTRUCTION

• Head up
  • Press and hold the HEAD UP button of the remote, the head actuator moves out, stop when released；
• Head down
  • Press and hold the HEAD DOWN button of the remote, the head actuator moves in, stop when released；
• Foot up
  • Press and hold the FOOT UP button of the remote, the foot actuator moves out, and stops when released;
• Foot down
  • Press and hold the FOOT DOWN button of the remote. The foot actuator moves in and stops when released
• Underbed light
  • Click the Underbed light button to open or shut the light under the bed.
• Massage head
  • Click the MASSAGE HEAD button, head massage motor switches massage intensity, massage intensity switches among 0-1-2-3；
• Massage foot
  • Click the MASSAGE Foot button, head massage motor switches massage intensity, massage intensity switches among 0-1-2-3；
• Massage timer
  • If the massage motors do not work, the button is invalid. If the massage motors are working, click the button to switch the massage time. When the massage time switches to 0, turn off the massage;
• Flat
  • Click the FLAT button, and the bed goes flat. Stop when you click any button during the process of going flat.
• Zero G
  • Click the ZG button, the actuator moves to the ZG position, stops when any button is clicked during the movement;
• Memory position
  • Click the memory position to move the actuator to the memory position.
• One-touch sleep
  • Trigger the sleep-inducing process and sequentially perform the series of sleep-inducing actions

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet the general RF exposure requirements.

IC RSS warning

This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions:

1. This device may not cause interference,
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference,
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Troubleshooting

• Massage Timer Button Not Working: Ensure that the massage motors are currently active. The massage timer button is only functional when the massage motors are running.
• Bed Movement Stops Unexpectedly: If the bed is moving to a “Flat” or “Zero G” position and stops, check if any other button was accidentally pressed. Pressing any button during these movements will halt the process.
• Remote Control Not Responding: Check the batteries. The remote requires 3 x AAA 1.5V batteries. Replace them if necessary.