Keeson RC309A Remote Control User Manual

Keeson RC309A Remote Control

Specifications

• Product Name: REMOTE CONTROL
• Model: RC309A
• Input: 2 x AAA 1.5V batteries
• Manufacturer: Keeson Technology Corporation Limited
• Country of manufacture: China

Usage Instructions

Figure 1 illustrates the buttons on the remote control.

1. Head up
   Press and hold the HEAD UP button of the remote, the head actuator moves out, stop when released.
2. Head down
   Press and hold the HEAD DC NNN button of the remote, the head actuator moves in, and stops when released.
3. Foot up
   Press and hold the FOOT UP button of the remote, the foot actuator moves out, stop when released.
4. Foot down
   Press and hold the FOOT button of the remote, the foot actuator moves in, stop when released.
5.  Flat
   lick FLAT button, the bed goes flat. Stop when you click any button during the process of going flat.
6. Massage head 
   lick MASSAGE HEAD button, head massage motor switches massage intensity, massage intensity switches among 0-1-2;
7. ZG button
   Click the ZG button, the actuator moves to the ZG position, stop when clicking any button during the movement.
8. Memory Favorite position
   licking once will move the app to the Favorite position; long-pressing to memorize the position. The backlight will flash twice, and releasing the button will continue the flashing.
9. Lock
   Press and hold the child lock button until the red light flashes twice, indicating that the child lock is successfully engaged. During the locking process, pressing any button will cause the red light to flash for 2 seconds, indicating that the lock is engaged.

Product information

• Product Name: REMOTE CONTROL
• Model: RC309B
• Input: 2 x Battery AAA 1.5V
• Manufacturer: Keeson Technology Corporation Limited
• Manufacturing country: China

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can adiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
• Consult the dealer or an experienced radio-TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirement. The device can be used in exposure condition without restriction.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence, exemplifying RSS standard(s). Operation is subject to the following two conditions:

• This device may not cause interference.
• This device must accept any interference, including interference that mav cause undesired operation of the device.

Troubleshooting

If the remote control is not functioning as expected:

• Check Batteries: Ensure that two AAA 1.5V batteries are correctly inserted and have sufficient charge.
• Child Lock: If the remote is unresponsive and the red light flashes for 2 seconds when a button is pressed, the child lock may be engaged. Refer to section 1.7 to disengage the child lock.
• Interference: This device complies with FCC rules regarding interference. If you experience unexpected operation, it might be due to external interference. Ensure there are no strong radio frequency sources nearby.

FAQs

Q: What type of batteries does the RC309A remote control use?
A: The remote control requires 2 x AAA 1.5V batteries.

Q: How do I stop the bed from moving once I’ve pressed a position button?
A: For continuous movements like Head Up/Down or Foot Up/Down, release the button to stop. For preset positions like Flat or ZG, clicking any button during the movement will stop the process.

Q: What does it mean if the red light flashes for 2 seconds when I press a button?
A: This indicates that the child lock feature is currently engaged. You will need to disengage the child lock to use the remote’s functions (refer to section 1.7).

Q: Can I modify the remote control?
A: Any changes or modifications not expressly approved by the manufacturer could void your authority to operate the equipment and are not recommended.