Keeson RC302F Remote Control User Manual

Keeson RC302F Remote Control

Specifications

• Product Name: REMOTE CONTROL
• Model: RC302F
• Input: 3 x Battery AAA 1.5V
• Manufacturer: Keeson Technology Corporation Limited
• Manufacturing Country: China

Usage Instructions

Basic Adjustments

• Head Up: Press and hold the ‘HEAD UP’ button. The head actuator will move out. Release to stop.
• Head Down: Press and hold the ‘HEAD DOWN’ button. The head actuator will move in. Release to stop.
• Foot Up: Press and hold the ‘FOOT UP’ button. The foot actuator will move out. Release to stop.
• Foot Down: Press and hold the ‘FOOT DOWN’ button. The foot actuator will move in. Release to stop.
• Lumbar Up: Press and hold the ‘LUMBAR UP’ button. The lumbar actuator will move out. Release to stop.
• Lumbar Down: Press and hold the ‘LUMBAR DOWN’ button. The lumbar actuator will move in. Release to stop.
• Tilt Up: Press and hold the ‘TILT UP’ button. The head tilt actuator will move out. Release to stop.
• Tilt Down: Press and hold the ‘TILT DOWN’ button. The head tilt actuator will move in. Release to stop.

Special Functions

• UBB (Underbed Light): Click the ‘UBB’ button to turn the underbed light on or off.
• Massage Head +: Click the ‘MASSAGE HEAD +’ button to cycle through head massage intensity levels (0-1-2-3).
• Massage Head -: Click the ‘MASSAGE HEAD -‘ button to gradually decrease head massage intensity (3 levels).
• Massage Foot +: Click the ‘MASSAGE FOOT +’ button to cycle through foot massage intensity levels (0-1-2-3).
• Massage Foot -: Click the ‘MASSAGE FOOT -‘ button to gradually decrease foot massage intensity (3 levels).
• Massage Timer: If massage motors are active, click this button to switch the massage time. Setting the timer to ‘0’ will turn off the massage. This button is inactive if massage motors are off.
• Flat: Click the ‘FLAT’ button to return the bed to a flat position. The process will stop if any other button is clicked during movement.
• Zero G (ZG): Click the ‘ZG’ button to move the bed to the Zero Gravity position. The movement will stop if any other button is clicked during the process.
• Memory Position: Click the ‘MEMORY POSITION’ button to move the bed actuators to a pre-set memory position.

Overview

1. Head up
   Press and hold the HEAD UP button of the remote, the head actuator moves out, stop when released.
2. Head down
   Press and hold the HEAD DOWN button of the remote, the head actuator moves in, and stops when released.
3. Foot up
   Press and hold the FOOT UP button of the remote, the foot actuator moves out, stop when released.
4. Foot down
   Press and hold the FOOT DOWN button of the remote, the foot actuator moves in, stop when released.
5. Lumbar up
   Press and hold the LUMBAR UP button of the remote. The lumbar actuator moves out and stops when released.
6. Lumbar down
   Press and hold the LUMBAR DOWN button of the remote, the lumbar actuator moves in, and stops when released.
7. Tilt up
   Press and hold the TILT UP button of the remote, the head tilt actuator moves out, and stops when released.
8. Tilt down
   Press and hold the TILT DOWN button of the remote, the head tilt actuator moves in, and stops when released.
9. UBB
   Click the Underbed light button to open or shut the light under the bed.
10. Massage head +
    Click the MASSAGE HEAD button, head massage motor switches massage intensity, massage intensity switches among 0-1-2-3；
11. Massage foot +
    Click the MASSAGE Foot button, head massage motor switches massage intensity, massage intensity switches among 0-1-2-3；
12. Massage head –
    Clicking will cause the intensity of the head massage to gradually decrease, with a total of 3 levels.；
13. Massage foot –
    Clicking will cause the foot massage intensity to cycle and decrease gradually, with a total of 3 levels.；
14. Massage timer
    If the massage motors do not work, the button is invalid. If the massage motors work, click the button to switch the massage time. When the massage time switches to 0, turn off the massage.
15. Flat
    Click the FLAT button, and the bed goes flat. Stop when you click any button during the process of going flat.
16. ZG button
    Click the ZG button, the actuator moves to the ZG position, and stops when any button is clicked during the movement.
17. Memory position
    Click the memory position to move the actuator to the memory position.

FCC STATEMENT

FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

• The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

ISED RSS Warning
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This devicemay not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Troubleshooting

• Remote not responding: Ensure batteries are correctly inserted and not depleted. Replace with new AAA 1.5V batteries if necessary.
• Bed not moving: Check if the remote’s batteries are working. Ensure no obstructions are preventing bed movement. If the bed is stuck, try pressing the ‘FLAT’ button.
• Massage not working: Ensure the massage motors are turned on. The ‘Massage Timer’ button will be invalid if the motors are off.
• RF Exposure: The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

FAQs

• Q: What type of batteries does the remote use?
  • A: The RC302F remote control uses 3 x AAA 1.5V batteries.
• Q: How do I stop the bed from moving to a preset position (eg, Flat or Zero G)?
  • A: You can stop the bed’s movement to a preset position by clicking any other button on the remote during the process.
• Q: Can I adjust the massage intensity?
  • A: Yes, you can increase head/foot massage intensity using ‘MASSAGE HEAD +’ / ‘MASSAGE FOOT +’ buttons and decrease it using ‘MASSAGE HEAD -‘ / ‘MASSAGE FOOT -‘ buttons. There are 3 levels of intensity.
• Q: What does the UBB button do?
  • A: The UBB button controls the underbed light, turning it on or off with a click.
• Q: What should I do if the remote isn’t working after changing batteries?
  • A: Ensure the new batteries are inserted with the correct polarity. If the issue persists, contact Keeson Technology Corporation Limited customer support.