KAVACPOL01A P1 Pro Pool Robot User Guide

The indicator will turn green while charging and turn blue when fully charged.
Disconnect the power adaptor and replace the protective cover on the charging port.

Powering On and Selecting a Cleaning Mode:
To start the robot, move the ‘Cleaning Mode’ switch to the right. This will power on the robot and allow you to select the desired cleaning mode. Ensure the robot is fully charged before use.

Placing the Robot in the Pool:

Select the desired cleaning mode and place the robot in the water as soon as possible.
Slowly lower the robot into the water. The robot will release any air in the body and sink to the bottom of the pool.

The robot will start cleaning within 10 seconds after reaching the bottom of the pool.

Removing the Robot from the Pool:

The robot will automatically stop at the bottom edge of the swimming pool once the cleaning program has been completed or when the battery power is low.
Use the provided hook to carefully lift the robot from the pool.

After removing, place the ‘Cleaning Mode’ switch into the ‘OFF’ position.
The filter basket should be emptied and cleaned after every cleaning cycle. Refer to the ‘Cleaning & Care’ section.

Safety & Warnings

Read this user guide carefully before using the product for the first time, and keep it for future reference.
This product is intended for domestic use only and should not be used for commercial or industrial purposes.

The product has undergone rigorous testing, including underwater tests, before leaving the factory. Some water droplets or dirt may be present inside, which will not affect performance.
Do not operate the product while people or animals are in the pool.

Fully charge the robot before first use.
Only use the provided power adaptor for charging. Do not use third-party adaptors, extension cables, or charge near combustible materials.

Do not use a damaged power adaptor. If the power cord is damaged, it must be replaced by Kogan.com, a service agent, or qualified personnel. Do not attempt to repair it yourself. Contact help.Kogan.com for support.
Ensure the charging port is dry before connecting to power.

Charge the product in a safe, dry location away from water.
Use an electrical outlet protected by a Residual Current Device (RCD) or a ground leakage circuit breaker.

Do not charge or use the robot if any abnormalities are detected. Contact help.Kogan.com for support.
This product is not suitable for use by individuals with reduced physical, sensory, or mental capabilities unless supervised by a responsible person.
Keep children supervised to prevent them from playing with the robot.
Children must not clean or maintain the product without supervision.
Dispose of all packaging materials properly and keep them away from children and pets.
This product contains a non-replaceable battery. Do not disassemble it. When the battery reaches the end of its life, dispose of the product properly.
Do not attempt to repair or modify any part of the product. If repairs are needed, contact help.Kogan.com for support.
Only qualified professionals should service this product, especially for the installation and maintenance of pool equipment. Always follow safety instructions.
Before cleaning or performing maintenance on the robot, unplug it from the electrical outlet.
Do not puncture, impact, or expose the robot to excessive temperatures.
Remove the battery before recycling or disposing of the product. Disconnect from power before removing the battery.
Dispose of used batteries according to local regulations. Seek professional recycling services if necessary.
The motor’s oil seal contains grease, which may cause minor water pollution if the motor is damaged. If a leak is suspected, cease use immediately and contact help. Kogan.com for support.
Charge the product at least 3 metres away from the pool’s edge.
Use the robot only under the following water conditions:

Chlorine Max 4 ppm

PH 7.0-7.4

Temperature 5-35°C (41-95°F)

Sodium chloride Max 5000 ppm

Maximum operating depth 2.5m

Components

Maintenance Kit

Combined machine screw 1 (x2)
Combined machine screw 2 (x2)
Self-tapping screw 1 (x4)

Self-tapping screw 2 (x4)
Flip buckle hand piece (x1)
Circlip (x4)

Rubber strip (x1)

Overview

Operation

Charging
Fully charge the robot before first use.

Remove the robot from the pool and turn it off.
Remove the protective cover and ensure the charging port is properly dried.
Connect the provided power adaptor to the charging port.

Connect the power adaptor to an electrical outlet.
The indicator will turn green while charging and turn blue when fully charged.
Disconnect the power adaptor and replace the protective cover on the charging port.
Notes:
- Charge the product in a safe, dry location away from water.
- Charge the product at least 3m away from the pool’s edge.

Indicator

Indicator	Status
Green	Sufficient battery
Blue	Insufficient battery
Orange	Very low battery
Red	Fault

Powering On and Selecting a Cleaning Mode
To start the robot, move the ‘Cleaning Mode’ switch to the right. This will power on the robot and allow you to select the desired cleaning mode. Ensure the robot is fully charged before use.

Switch Position	Cleaning Mode	Cleaning Area
AUTO	Intelligent cleaning	Clean the floor/wall/waterline
FLOOR	Floor cleaning	Clean only the floor
WALL	Wall cleaning	Clean the wall and waterline
OFF	Off	N/A

Placing the Robot in the Pool

Select the desired cleaning mode and place the robot in the water as soon as possible.
Slowly lower the robot into the water. The robot will release any air in the body and sink to the bottom of the pool.

The robot will start cleaning within 10 seconds after reaching the bottom of the pool.

Removing the Robot from the Pool

The robot will automatically stop at the bottom edge of the swimming pool once the cleaning program has been completed or when the battery power is low.
Use the provided hook to carefully lift the robot from the pool.
After removing, place the ‘Cleaning Mode’ switch into the ‘OFF’ position.
The filter basket should be emptied and cleaned after every cleaning cycle. Refer to the ‘Cleaning & Care’ section.

Cleaning & Care

Cleaning the Filter Basket
The filter basket must be cleaned after every cleaning cycle.

Open the filter compartment cover.

Remove the filter basket.
Open the filter basket cover and remove any debris.

Rinse the filter basket and place the filter basket back into the filter compartment.

Note:
Regularly clean the filter basket to maintain optimal performance. A clogged filter can reduce suction and prevent the robot from effectively collecting dirt and debris. If cleaning does not restore performance, the filter basket may need to be replaced. Contact help.Kogan.com for support.

Maintenance

For optimal performance, ensure the robot is properly maintained by following these scheduled instructions.

Daily Maintenance:

Clean the robot and filter basket after each cleaning cycle.
Keep the robot away from direct sunlight.

Ensure the charging port is dry before charging.

Periodic Maintenance:

Every 3-4 months: Inspect and clean the roller brushes, tracks, and gears.

Every 12 months: Check for wear on tracks and roller brushes. Replace if necessary.

Off-season Storage:

Thoroughly clean and dry all components before storage.

Fully charge the battery before storing.
Store in a cool, dry place (5-45°C, humidity <80% RH).
Charge the battery at least every 3 months to prevent over-discharge.

Keep out of reach of children and unauthorised users.

Parts Replacement

Roller Brush:

Remove the silicone buckles securing the roller brush.

Replace with a new roller brush and secure the buckles.

Track Replacement:

Remove the side panels: Use a Phillips head screwdriver to remove the 2 screw covers. Unscrew the 2 screws securing the side panels and track panels.
Carefully detach and set aside the side panels and track panels. Ensure that no debris or dirt is present in the track housing before proceeding with the replacement.

Remove the tracks.
Clean and dry all the comcomponentsside of the panels.

Replace the tracks and reassemble the side panels.
Repeat the process for the other side of the robot.

Specifications

Applicable pool size 100m2 (1,076ft2)

Pool depth 0.5-2.5m (1.64-8.2 ft)
Robot dimensions 488 x 419 x 237mm
Robot weight 9.9kg

Charger input 100-240V~50/60Hz
Charger output 29.2V=3A (US: 29.4V=3A)
Robot input 29.2V=3A (US: 29.4V=3A)

Lithium battery capacity 5,200mAh (Max.)
Battery life ≥ 2 hours
Charging time:e 2.5 hours

Filter density 180μm
Moving speed 10-15m/min
Waterproof rating IP68

Storage temperature -20°C to +45°C

FAQ

If an issue persists after the suggested solutions are implemented, contact help.Kogan.com for support.

Issue	Possible Cause	Solutions
The robot is not charging.	The electrical outlet has no power.	Check whether the electrical outlet is working.
	The power cord is not properly connected to the electrical outlet.	Check the connection between the power cord and the electrical outlet.
	The connection between the power adaptor and the robot is loose.	Check the connection between the robot and the power adaptor.
	The power adaptor is not working.	Ensure the indicator illuminates when the adaptor is connected to the robot. If not, replace the charger. Contact help.Kogan.com for support
	Water has entered the charging port.	Dry the charging port and try charging again.
The robot is not working, or the indicator is not on.	The battery is flat.	Fully charge the battery.
The robot is not working, or the indicator is not on.	Check that the ‘Cleaning Mode’ switch is in the correct position	Place in the ‘OFF’ position and then try again.
The robot is not cleaning the pool walls.	The battery is too low.	Fully charge the battery.
	Check the ‘Cleaning Mode’ switch.	Place the ‘Cleaning Mode’ switch in either ‘AUTO’ or ‘WALL’
	The filter basket is clogged.	Clean the filter basket.
	There is algae on the wall, and the pH value is not right.	Check the levels of chemicals in the water. Poor water quality can allow algae to grow, making walls slippery. In this case, adjust the water quality and manually scrub the walls.
	The tracks and/or roller brushes are worn.	Replace the tracks and/or roller brushes.

The robot moves in circles.	The filter basket is clogged.	Clean the filter basket.
The robot moves in circles.	Debris is stuck on the tracks or roller brushes.	Remove any debris from tracks or roller brushes.
The robot stops underwater, and the indicator is red.	Debris is stuck on the tracks or roller brushes.	If the motor is stuck, check whether the left/right track can be manually rotated. If not, check for any obstructions on the track.
The robot stops underwater, and the indicator is red.	Debris blocks the water pump motor impeller.	If the water pump motor is stuck, check for obstacles on the impellers.
There are water droplets and dirt in the newly purchased robot.	Every robot has undergone rigorous testing before leaving the factory, including underwater testing. Therefore, there may be a trace amounts of water droplets or dirt remaining inside.	This is normal and will not affect the operation of the robot.

Disposal

This marking indicates that this appliance should not be disposed of with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Need more information?

We hope that this user guide has given you the assistance needed for a simple setup.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.Kogan.com.

AQ

How often should I clean the filter basket?
The filter basket must be cleaned after every cleaning cycle to maintain optimal performance. If cleaning does not restore performance, consider replacing the filter basket. Contact help.Kogan.com for support.

Documents / Resources

KAVAC KAVACPOL01A P1 Pro Pool Robot [pdf] User Guide
KAVACPOL01A P1 Pro Pool Robot, KAVACPOL01A P1, Pro Pool Robot, Pool Robot, Robot

References

User Manual

KAVACPOL01A P1 Pro Pool Robot

Product Specifications

Product Usage Instructions