VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
“
Spesifikasi Produk
| Model No. | VFD-750C-230 |
|---|---|
| PWM Output | (Cathetan 1,2,3,4) |
| Vol inputtage Range (UVW) | 380Vmax, line-to-line voltage 0 ~ 268V luwes karo modulated PWM, cocok kanggo motor kelas 3PH 200-240V |
| Daya Rated | 350W |
| Efisiensi | DC BUS VOLTAGE PWM FREKUENSI RATED INPUT VOLTAGE: 2.5 KHz ~ 15 KHz, 90 ~ 264VAC |
Pandhuan Panggunaan Produk
1. Instalasi
Tindakake langkah iki kanggo nginstal VFD-750C-230:
- Priksa manawa sambungan listrik sing tepat digawe miturut
ditemtokake voltage sawetara. - Pasang modul kanthi aman ing papan sing cocog.
2. Operasi
Kanggo ngoperasikake VFD-750C-230:
- Gunakake daya ing vol sing ditemtokaketage sawetara.
- Ngontrol modul nggunakake sinyal PWM sing kasedhiya.
3. Pancegahan Safety
Kanggo nggunakake produk sing aman:
- Aja mbabarake modul menyang kelembapan utawa ekstrem
suhu. - Aja operate modul ngluwihi daya dirating lan saiki
watesan.
Pitakonan sing Sering Ditakoni (FAQ)
Q: Apa saiki inrush maksimum kanggo
VFD-750C-230?
A: Saiki inrush maksimum kanggo wiwitan kadhemen punika 50A ing
230VAC.
P: Kepiye carane bisa ngontrol VFD-750C-230?
A: modul bisa kontrol nggunakake sinyal PWM 3-phase minangka
kasebut ing manual.
“`
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
Manual pangguna
Video
IEC61800-5-1
Bauar t gepruft Sicherheit
egelma ge od os be wac g
www.tuv.com ID 2000000000
BS EN/EN61800-5-1
TPTC004
~
https://www.meanwell.com/serviceGTIN.aspx
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
SPESIFIKASI
MODEL NO. PWM OUTPUT
(Cathetan 1,2,3,4)
INPUT
KONTROL / FUNGSI
(Cathetan 5)
LINGKUNGAN PERLINDUNGAN
KESELAMATAN & EMC
CATETAN LAIN
VFD-750C-230
VOLTAGE RANGE (UVW)
380Vmax, line-to-line voltage 0 ~ 268V luwes karo modulated PWM, cocok kanggo 3PH 200-240V kelas motor
SAIKI
Rated Peak
3A 6A kanggo 5 detik
DAYA RATED
350W
EFISIENSI DC BUS VOLTAGE
93% 380±5VDC
PWM FREKUENSI RATE INPUT VOLTAGE
2.5 KHz ~ 15 KHz 90 ~ 264VAC
JANGKA FREKUENSI INPUT (Hz) 47 ~ 63Hz
FAKTOR DAYA (Jenis.)
PF>0.99/115VAC, PF>0.93/230VAC ing beban penuh
RATED INPUT SAIKI
8A / 115VAC 4A / 230VAC
KAWASAN INRUSH
wiwitan kadhemen 50A / 230VAC
LEAKAGE SAIKI 3-PHASE PWM CONTROL
<2mA/240VAC PWM sinyal kontrol kanggo driver gerbang kanggo IGBTs. (CN93, PIN8~13) 3.3V TTL/CMOS input: Dhuwur (> 2.7V): IGBT ON; Kurang (<0.4V): IGBT OFF
3-PHASE SENSOR SAIKI DC BUS VOLTAGE SENSOR
Built-in 100m resistor shunt sisih ngisor ing fase UVW (CN93, PIN4~6)
DC BUS voltage sensor output (CN93, PIN1) 2.5V@DC BUS 380V
SENSOR THERMAL
10K NTC sing dibangun kanggo ngrasakake suhu operasi IGBT. (TSM2A103F34D1R (Thinking Electronic), PIN3 saka CN93)
FAULT SIGNAL AUXILIARY POWER
Sinyal kesalahan inverter (Short circuit/OCP, CN93, PIN7).
3.3V TTL/CMOS output: Normal: High(>3V); Abnormal: Low (<0.5V) Non-terisolasi 15V daya output kanggo papan kontrol eksternal (CN93,PIN 14 kanggo PIN2) 15V@0.1A; Toleransi +/- 0.5V, Ripple 1Vp-p maks
SHORT CIRCUIT KERJA TEMP.
Jinis pangayoman: Mati o/p voltage, urip maneh kanggo mbalekake -30 ~ +60 (Deleng "Kurva Ngimpi")
KERJA Asor STORAGE TEMP., Asor
20 ~ 90% RH non-kondensasi -40 ~ +85, 10 ~ 95% RH non-kondensasi
GETERAN
10 ~ 500Hz, 2G 10min./1siklus, wektu kanggo 60min. saben sumbu X, Y, Z
STANDAR KESELAMATAN
CB IEC61800-5-1,TUV/BS EN/EN61800-5-1,EAC TP TC004 disetujoni
Tahan VOLTAGE
I/P-FG: 2KVAC
RESISTANCE Isolasi
I/P-FG: 100M Ohm/500VDC/25/70%RH
Paramèter
Standar
Test Level / Cathetan
EMISI EMC
Dilaksanakake Radiated Harmonic Current Voltage Kelip-kelip
BS EN/EN IEC61800-3 BS EN/EN IEC61800-3 BS EN/EN IEC61000-3-2 BS EN/EN61000-3-3
Kelas A, C2 Kelas A, C2 Kelas A —–
BS EN/EN IEC61800-3, lingkungan kapindho
KEMALANGAN EMC
Parameter ESD Radiated EFT/Burest Surge Conducted Magnetic Field
Standar BS EN/EN61000-4-2 BS EN/EN IEC61000-4-3 BS EN/EN61000-4-4 BS EN/EN61000-4-5 BS EN/EN61000-4-6 BS EN/EN61000-4-8
Test Level / Cathetan Level 3, 8KV air ; Level 2, 4KV kontak Level 3 Level 3 Level 3, 2KV/Line-Earth ; Level 3, 1KV/Line-Line Level 3 Level 4
Voltage Dips lan Interupsi BS EN/EN IEC61000-4-11
>95% dip 0.5 periode, 30% dip 25 periode, >95% gangguan 250 periode
MTBF
Voltage penyimpangan
IEC 61000-2-4 Kelas 2
± 10% Un
Total Harmonic distortion (THD) Individual Harmonic orders
IEC 61000-2-4 Kelas 3 IEC 61000-4-13 Kelas 3
THD 12%
Variasi frekuensi
IEC 61000-2-4
± 4%
Tingkat owah-owahan frekuensi
IEC 61000-2-4
2%/s
2863.4K jam min.Telcordia SR-332 (Bellcore); 310.5K jam min.MIL-HDBK-217F (25)
UKURAN (L * W * H)
150 * 100 * 41 mm
KEMASAN
0.8Kg; 30pcs/25kg/1.64CUFT
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
Diagram Blokir
ACL ACN FG
Saringan EMI
SIRKUIT PFC
380VDCBus
UH
VH WH GATE DRIVE KONTROL UL
VL WL FAULT ITRIP
DAYA AUX
SHORTCIRCUIT PROTEKSI
HV+ HV-
suhu IGBT
sensor
V/I KURVE
Io
6A
Puncak arus
U
(5 detik)
V
3.24A
W
3A
1.62A
Tugas terus menerus S1 area
RSH_U RSH_V RSH_W PWM_UH PWM_UL PWM_VH PWM_VL PWM_WH PWM_WL FAULT HV+ sensor
HV-
Vaux_15V
RTH
150V
268V
Vo
Kurva Derating
Output Derating VS Input Voltage
BEBAN (%)
100
80
Pendinginan konduksi
or
Dipeksa hawa cooling
50
40
Pendinginan konveksi
30
20
-30
0
10
20
30
40
50
60 70 (HORIZONTAL)
TEMPERATUR AMBIEN
BEBAN (%)
100
90
80
70
60
Kanthi Kipas 23.5CFM
50 40
90 95 115 120 130 140 160 180 200 220 240 264
INPUT VOLTAGE (VAC) 60Hz
Puncak Arus
200%
80% 5 detik.
55 sek.
EFISIENSI (%)
Efisiensi vs Beban
100% 95% 90% 85% 80% 75% 70% 65% 60%
30% 40% 50% 60% 70% 80% 90% 100%
115VAC 230VAC
MUNGKIN
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
Manual Fungsi
1. 3-phase PWM Control (CN93, PIN8 ~ 13) VFD-750C-230 menehi sirkuit enem-ngalih kanthi nggunakake 3 setengah jembatan IGBT. IGBT saben fase dikontrol dening PWM_UH/UL, PWM_VH/VL lan PWM_WH/WL (PIN 8~13). Syarat input kanggo PWM kompatibel karo sinyal TTL lan CMOS 3.3V. Mangga deleng diagram ing ngisor iki.
PIN 13 PWM_UL PIN 12 PWM_UH PIN 11 PWM_VL PIN 10 PWM_VH PIN 9 PWM_WL PIN 8 PWM_WH
Kertu Kontrol MCU eksternal
PWM
MCU
PÈNGET: Sampeyan kudu tetep mati-mati minimal antarane ngalih ndhuwur lan ngisor saben phase.
t mati
t mati
tdead (Min.)
300ns
PWMxH
PWMxL
t sw
Output Voltage
VX
380V 0V
tdead : Ngalih mati-wektu t sw : Ngalih wektu
x = U, V, W
2. Deteksi Arus 3 fase & Perlindhungan Arus Luwih (CN93, PIN4~6)
Resistor shunt sisih ngisor 100m dipasang ing saben fase VFD-750C-230 kanggo pangukuran saiki lan deteksi sirkuit cendhak. Disaranake kanggo nyepetake sirkuit deteksi eksternal lan ndeteksi sinyal kasebut nganggo OPA. Mangga deleng diagram ing ngisor iki.
PIN 6 RSH_W PIN 5 RSH_V PIN 4 RSH_U PIN 2 HV-
Voff nyetel
Kertu Kontrol MCU eksternal
x3
+ OPA
–
IU ADC MCU
Yen output saiki ngluwihi 200% nilai dirating, sirkuit pangayoman internal bakal micu lan mateni driver gapura kanggo pangayoman.
Gate - drive
ITRIP
Voc U
COMP
Voc V Voc W
Short-circuit
Iu
pangayoman
Iv
Iw
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
3. BUS DC Voltage Deteksi (CN93, PIN1) VFD-750C-230 dibangun karo DC bus voltage sensor (sensor HV+, PIN 1). Sensor menehi output 2.5V nalika DC bus voltage ing 380V. Disaranake kanggo ndeteksi sinyal kasebut dening OPA. Nalika voltage saka bis DC ngluwihi 420V, sinyal input PWM kudu mati kanggo pangayoman.
Kertu Kontrol MCU eksternal
PIN1 sensor HV+
+ OPA
–
ADC MCU
Nyata DC Bus voltase ge (V)
Persamaan kanggo DC bus voltage pitungan: VDC BUS = 380 x HV + sensor
2.5
Spesifikasi sensor HV+ 600 400 200
0
0.00
1.00
2.00
3.00
4.00
output sensor HV+ voltage (V)
4. Deteksi Suhu IGBT (CN93, PIN3)
VFD-750C-230 dibangun ing sensor suhu kanggo ndeteksi suhu modul daya. Pangguna bisa ndeteksi suhu modul daya kanggo pangayoman. Sirkuit deteksi sing disaranake ana ing ngisor iki. Disaranake kanggo mateni input PWMs, yen pin 3 voltage ngluwihi 3.3V.
PIN 3 RTH
Vtemp
MCU kertu kontrol MCU njaba
PIN 2 HV-
5. Fault sinyal
Yen VFD-750C-23 nemokke kondisi overcurrent lan tetep ing negara kanggo wektu overcurrent minimal, sinyal FAULT bakal diaktifake (aktif kurang) kanggo ngabari controller external utawa sirkuit.
Output Saiki
t Tripmin.
200% dirating saiki
tTripmin.
1an
PIN7 FAULT
t Tripmin.
5an
Min. wektu tripping liwat-saiki
6. Rekomendasi Rem (CN100, PIN1,3)
VFD-750C-230reserved CN100 PIN1,3 sing nyambung menyang HV+,HV- kanggo desain sirkuit rem. Maksimum voltage ing DC Bus(HV+) ora luwih saka 420V.
Kertu Kontrol MCU eksternal
CN93 PIN1 HV+ Sensor TB100 PIN3 HV-
TB100 PIN1 HV+
Vref COMP Gate drive
Resistor Rem HV+
HV-
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
Spesifikasi Mekanik
(Satuan: mm, toleransi ± 1mm)
150
143
3.5
8
6 7.62
3 2 1 TB1
TB100 5 4 3 2 1
4-4.2 L=6
7.62
6
84
100
1
13
CN93
2
14
1
13
2
14
41
Pin Terminal Input AC NO. Tugas (TB1)
Pin No. Tugas
1
AC/L
2
AC/N
3
Pin Terminal Output NO. Tugas (TB100)
No. Pin Tugas No. Pin
1
W
4
HV-
2
V
5
HV+
3
U
TB100 Pin4, Pin5 digunakake kanggo nginstal piranti brake regenerative, Nyingkiri karusakan VFD-750C-230.
Kontrol Pin NO. Tugas (CN93): HRS DF11-14DP-2DS utawa sing padha
No. Pin Tugas No. Pin
1
Sensor HV+
8
PWM_W H
2
HV-
9
PWM_W L
3
RTH
10
PWM_V H
4
RSH _U
11
PWM_V L
5
RSH _V
12
PWM_U H
6
RSH _W
13
PWM_U L
7
LUPA
14
Vaux_15V
omah kawin: HRS DF11-14DS utawa padha karo Terminal HRS DF11-**SC utawa padha karo
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
No. Pin Kontrol Tugas (CN93):
Nomer Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Deskripsi Fungsi
Sensor HV+ DC BUS voltage output sensor, referensi kanggo pin 2 (HV-)
HV-DC BUS voltage sensor output lemah
Sensor suhu RTH
RSH_U RSH_V RSH_W FAULT
U phase output sensor saiki V phase output sensor saiki W phase output sensor saiki Swara deteksi saiki. Normal > 3V, Abnormal <0.5V
PWM_WH PWM_WL PWM_VH PWM_VL PWM_UH PWM_UL Vaux_15V
W phase input logika sisih dhuwur, ing> 2.7V; mati < 0.4VW phase low input logika sisi, on > 2.7V; mateni <0.4VV fase input logika dhuwur, on> 2.7V; mateni <0.4VV fase input logika sisi rendah, urip> 2.7V; mati <0.4VU fase input logika sisih dhuwur, ing> 2.7V; mati <0.4VU fase input logika sisi rendah, on> 2.7V; mati <0.4V Auxiliary voltage output 15V referensi kanggo pin2 (HV-). Arus beban maksimum yaiku 0.1A
Aplikasi
Aplikasi example: aplikasi drive BLDC
Input AC
ACL ACN FG
VFD-750C-230
UVW
PWM_UH PWM_UL PWM_VH PWM_VL PWM_WH PWM_WL
Vaux_15V
LUPA
RTH
RSH_U
RSH_V
380VDC
Sensor RSHW HV+
HV+ HV- HV-
(TB100)(TB100)
Motor BLDC Kab
Beban Mekanik
poros
Sensor posisi Encoder / Hall-efek
Papan kontrol BLDC pangguna
Piranti rem pangguna
Kontrol Rem
1. Tokoh nuduhake sistem drive BLDC nyiyapake karo VFD-750C-230. 2. Pangembang bisa ngontrol sinyal PWM saka 6-switch kanthi nggunakake SPWM utawa SVPWM, etc. kanggo 3-phase voltage modulasi, lan mbangun basis metode kontrol
ing sensor shunt saiki ing 3-phase low-side switch (RSH_U/V/W) lan DC BUS voltage sensor (sensor HV +) sing diwenehake dening VFD-750C-230. 3.Developers bisa milih cocok BLDC sensor posisi kayata encoder utawa Hall-efek sensor pas aplikasi sing. 4. Disaranake nginstal sirkuit rem / piranti ing HV + / HV- pin (DC BUS, CN100) supaya DC BUS OVP nalika BLDC decelerating. 5. Disaranake kanggo mateni input PWM utawa nyambung menyang piranti resistor brake kanggo safety nalika DC Bus voltage luwih saka 420V. 6. Yen VFD-750C-230 ditrapake kanthi kontrol sing ora cocog, kayata nyepetake kanthi cepet utawa kontrol arus sing ala, bisa uga nyebabake VFD-750C-230
fault-state kanggo mateni output voltage (low-level ing FAULT pin).
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W Tipe Umum Variabel Frekuensi Drive kanthi fungsi PFC
Instalasi
1.Operate karo piring aluminium tambahan Supaya bisa ketemu "Kurva Derating" lan "Karakteristik statis", seri VFD kudu dipasang ing piring aluminium (utawa lemari ukuran sing padha) ing ngisor. Ukuran sing disaranake piring aluminium kapacak ing ngisor iki. Lan kanggo ngoptimalake kinerja termal, piring aluminium kudu duwe permukaan sing rata lan lancar (utawa dilapisi pelumas termal), lan seri VFD kudu dipasang kanthi kuat ing tengah piring aluminium.
M4*4
450
450
2.With 23.5CFM dipeksa online
23.5CFM
Penggemar
Arah aliran udara
75 mm
100 mm
3
File Name:VFD-750C-230-SPEC 2024-11-22
VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC
Dhaptar Aksesoris
Yen sampeyan duwe syarat kontrol aplikasi tartamtu, hubungi MEAN WELL kanggo rincian liyane. Papan kontrol motor (Papan kontrol motor lan modul drive VFD kudu dipesen kanthi kapisah):
Urutan MW No.
Papan kontrol
Saran Majelis
Jumlah
VFD-CB
1
Aplikasi Khas
1 Modul Frekuensi Variabel (seri VFD)
2 Papan kontrol Drive Frekuensi Variabel (Dirancang dening Panganggo utawa Soluton sing Disedhiyakake dening MEAN WELL
3 3-phase Pompa Motor
1 Baterei
2 Modul Frekuensi Variabel (seri VFD)
3 Papan kontrol Drive Frekuensi Variabel (Dirancang dening Panganggo utawa Soluton sing Disedhiyakake dening MEAN WELL)
4 3-phase Wheel Motor kanggo AGV Aplikasi
1 Modul Frekuensi Variabel (seri VFD)
2 Papan kontrol Drive Frekuensi Variabel (Dirancang dening Panganggo utawa Soluton sing Disedhiyakake dening MEAN WELL)
3 3-phase Fan Motor
4 HEPA kanggo Nyaring Udara
PAKET DEMO
Hubungi MEAN WELL kanggo rincian liyane.
VFD Demo Kit Fungsi Utama lan Fitur. 1 Dibangun ing VFD-350P-230 lan motor 230V. 2 Motor wiwitan / mandeg / maju / mundur / kontrol kacepetan. 3 Indikator wiwitan / mandeg / maju / mundur motor tengen. 4 Tampilan kacepetan motor (RDM). 5 Papan kontrol bisa diganti. 6 Ndhukung sambungan motor eksternal.
Manual Instalasi
Mangga deleng: http://www.meanwell.com/manual.html
File Name:VFD-750C-230-SPEC 2024-11-22
Dokumen / Sumber Daya
 |
MEAN WELL VFD-750C-230 750W AC Modul Penggerak Frekuensi Variabel Input kanthi Fungsi PFC [pdf] Manual Pamilik Modul Drive Frekuensi Variabel Input VFD-750C-230 750W AC kanthi Fungsi PFC, VFD-750C-230, Modul Drive Frekuensi Variabel Input 750W AC kanthi Fungsi PFC, Modul Drive Frekuensi Variabel kanthi Fungsi PFC, Modul Drive Kanthi Fungsi PFC, Kanthi Fungsi PFC |
