BHA2GSA Height Adjustable Workstation Think Desk
BHA2GSA
BHA3GSA
THINK Desk
Height-Adjustable Workstation
Includes Add-Ons: A1 | A2 | A3 | A4
General Installation Guide
Workstation
Overview
THINK Height-Adjustable Workstation
All parts listed are for a single workstation; additional parts will be needed for additional workstations.
Parts List
*If applicable.
WORKSTATION
1 | Determine Surface Size for Installation
Use the chart below to identify which arm brackets will be used with
surface size, and if surface will need replacement beam (BHANBEAM).
Note: Reference STEP 4 after completing STEP 2 and 3.
|
Surface Depth |
Surface Width |
Including Surface Dividers? |
Arm Bracket Type |
BHANBEAM |
Reference Step 4 |
|
24” |
36”-47” |
No |
Default |
Yes |
A |
|
24” |
36”-47” |
Yes |
BHA19 |
Yes |
B |
|
24” |
48” |
No |
Default |
No |
C |
|
24” |
48” |
Yes |
BHA19 |
No |
D |
|
24” |
54”-72” |
No |
Default |
No |
E |
|
24” |
54”-72” |
Yes |
Default |
No |
F |
|
30” |
36”-47” |
Yes/No |
Default |
Yes |
G |
|
30” |
54”-72” |
Yes/No |
Default |
No |
WORKSTATION
2 | Assemble Workstation Frame
Attach legs with motor and arm brackets to the center beam using screws (A).
Note: Replace default arm brackets if workstation requires BHA19 or T-brackets.
Surface width 36”-47” will need to replace beam, with replacement beam (BHANABEAM-without control box).
3 | Place Frame on the Surface
Loosen existing locking screws on adjustable beam to extend beam to fit table size. Run cord through cutout from the adjustable beam and secure the
handset to control box. Attach the short extension cord to the motor closest to control box and attach the longer extension cord on the opposite end.
4 | Adjust Frame on Surface
Note: Based on STEP 1 surface size chart, reference one of the following workstation diagrams to secure frame.
(A) 24”D x 36”–47”W Surfaces Without Side Dividers
Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
(B) 24″D x 36″–47″W Surfaces With Side Dividers
If using side dividers, frame will include arm brackets BHA19. Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
BHA19 Brackets
(C) 24”D x 48”W and Smaller Surfaces Without Side Dividers
Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
(D) 24”Dx48”W and Smaller Surfaces With Side Dividers
If using side dividers, frame will include arm brackets BHA19. Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
BHA19 Brackets
(E) 24”D x 54”–72”W Surfaces Without Dividers
Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
(F) 24”D x 54”–72”W Surfaces with Side Dividers
If using side dividers, inset the frame 2” from each end. Center arm brackets to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C).
Note: If using side dividers AND a facing divider with BSBHL, replace the arm brackets with BHA19.
(G) 30” Deep Surfaces
Extend the frame equal to the surface width. Center arm brackets to surface depth. Secure frame to surface using wood screws (B) and secure handset ORKSTATION SECTION
using wood screws (C).
5 | Secure Power Cord & Install Feet
Secure power cord to the control box. Secure locking screws on the adjustable beam and install the feet using screws (D) for each leg. If workstation is complete, flip over. Reference handset guide for initialization and operation functions.
Note: Use T-feet if using T-arm brackets.
A1: Casters
Overview
THINK Height-Adjustable Workstation
All parts listed are for a set of 4 casters;
additional parts will be needed for additional casters.
Parts List
|
Code |
Qty. |
Description |
|
|
BHACAST |
1 |
Caster Kit (Set of 4) |
|
|
16 |
Screws |
|
|
CASTERS
1 | Remove Glides From Feet
Unscrew all four glides from feet and disregard.
2 | Attach Casters to Feet
The workstation’s feet have pre-drilled holes for the caster plate. Attach casters using self-tapping metal screws.
A2: Modesty Panel
Overview
THINK Height-Adjustable Workstation
All parts listed are for a single modesty panel; additional parts will be needed for additional modesty panels.
Parts List
|
Code |
Qty. |
Description |
|
|
GLMP## |
1 |
Laminate Modesty Panel* |
|
|
4 |
Machine Screws |
|
|
|
BMPBFB |
2 |
L-Brackets |
|
|
4 |
Wood Screws |
|
|
*For Steel Modesty Panel: components may vary, but process is similar.
1 | Secure Brackets to Modesty Panel
Connect the BMPBFB bracket to the modesty panel using screws. Secure tightly.
END OF M
2 | Attach Modesty Panel to Surface
Attach modesty panel to surface using wood screws provided with brackets. Panel will be center aligned and flushed with back of surface.
A3: Slim Pedestal
Overview
THINK Height-Adjustable Workstation
All parts listed are for a single slim pedestal; additional parts will be needed for additional slim pedestals.
SLIM PEDESTAL
Parts List
|
Code |
Qty. |
Description |
|
|
BFSLM.SM |
1 |
Large Mounting Bracket |
|
|
1 |
Small Mounting Bracket |
|
|
|
BFSLM |
1 |
Slim Pedestal |
|
|
BFSLM.HW |
8 |
Machine Screw |
|
|
10 |
Wood Screw |
|
|
SLIM PEDESTAL
1 | Secure Brackets to Slim Pedestal
Align large mounting bracket to front of pedestal and align small mounting bracket to back. Secure both brackets using provided screws.
END OF SLIM PEDESTAL SECTION
2 | Attach Slim Pedestal to Surface
Secure pedestal to surface using wood screws. The pedestal brackets will connect on either side of the center beam.
A4: Cable Tray
Overview
THINK Height-Adjustable Workstation
All parts listed are for a single cable tray; additional parts will be needed for additional cable trays.
CABLE TRAY
Parts List
|
Code |
Qty. |
Description |
|
|
BHCT |
1 |
Surface-Mount Cable Management Tray |
|
|
10 |
Wood Screws |
|
|
CABLE TRAY
1 | Extend Cable Tray to Desired Length Extension range: 25″–45″.
END OF CABLE TRAY SECTION
2 | Attach Cable Tray to Surface
Attach cable tray using wood screws.
A4: Cable Tray
Overview
THINK Height-Adjustable Workstation All parts listed are for a single cable tray;
additional parts will be needed for additional cable trays.
Parts List
1 | Extend Cable Tray to Desired Length
Extension range: 25″–45″.
2 | Attach Cable Tray to Surface
Attach cable tray using wood screws.
1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com © 2023 Juniper Office | Version 23.0.0
Documents / Resources
 |
Juniper BHA2GSA Height Adjustable Workstation Think Desk [pdf] Instruction Manual BHA2GSA, BHA2GSA Height Adjustable Workstation Think Desk, Height Adjustable Workstation Think Desk, Adjustable Workstation Think Desk, Workstation Think Desk, Think Desk, Desk |
