Juniper | Office Furniture for the Entire Workspace
Instruction Manual for Juniper models including: BHA2GSA, BHA2GSA Height Adjustable Workstation Think Desk, Height Adjustable Workstation Think Desk, Adjustable Workstation Think Desk, Workstation Think Desk, Think Desk, Desk
Think Desk | Juniper Office Furniture
File Info : application/pdf, 28 Pages, 2.25MB
DocumentDocumentBHA2GSA BHA3GSA THINK Desk Height-Adjustable Workstation Includes Add-Ons: A1 | A2 | A3 | A4 General Installation Guide TABLE OF CONTENTS Edition Code BHA :: Workstation.................................................................................... 1 Add-ons A1 :: Casters .................................................................................................. 9 A2 :: Modesty Panel............................................................................... 13 A3 :: Slim Pedestal...................................................................................17 A4 :: Cable Tray ........................................................................................ 21 Workstation Overview THINK Height-Adjustable Workstation All parts listed are for a single workstation; additional parts will be needed for additional workstations. 1 WORKSTATION Parts List Code Qty. Description ###### 1 1 1 2 2 BHA3GSA 1 or BHA2GSA 1 1 8 24 3 8 BHANBEAM* 1 BHA19* 2 TLEG. ADAPTGSA* 1 BASB72* 1 Surface Center-Adjustable Beam Feet (Set of 2) 23" Arm Bracket Leg with Motor Handset Short & Long Extension Cord Power Cable Screw (A) Screw (B) Screw (C) Screw (D) BOOST Replacement Beam 19" Arm Bracket T-Leg Adapter (Set of 2) 42" Support Bar *If applicable. 2 WORKSTATION 1 | Determine Surface Size for Installation Use the chart below to identify which arm brackets will be used with surface size, and if surface will need replacement beam (BHANBEAM). Note: Reference STEP 4 after completing STEP 2 and 3. Surface Depth Surface Width Including Surface Dividers? 24" 36"-47" No 24" 36"-47" Yes 24" 48" No 24" 48" Yes 24" 54"-72" No 24" 54"-72" Yes 30" 36"-47" Yes/ No 30" 54"-72" Yes/ No Arm Bracket Type Default BHA19 Default BHA19 Default Default Default Default BHANBEAM Reference Step 4 Yes A Yes B No C No D No E No F Yes G No 3 WORKSTATION 2 | Assemble Workstation Frame Attach legs with motor and arm brackets to the center beam using screws (A). Note: Replace default arm brackets if workstation requires BHA19 or T-brackets. Surface width 36"-47" will need to replace beam, with replacement beam (BHANABEAM-without control box). BHA19 BHANABEAM 3 | Place Frame on the Surface Loosen existing locking screws on adjustable beam to extend beam to fit table size. Run cord through cutout from the adjustable beam and secure the handset to control box. Attach the short extension cord to the motor closest to control box and attach the longer extension cord on the opposite end. Locking Screws Short Ext. Cord Long Ext. Cord 4 WORKSTATION 4 | Adjust Frame on Surface Note: Based on STEP 1 surface size chart, reference one of the following workstation diagrams to secure frame. (A) 24"D x 36"47"W Surfaces Without Side Dividers Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). (B) 24"D x 36"47"W Surfaces With Side Dividers If using side dividers, frame will include arm brackets BHA19. Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). BHA19 Brackets 5 WORKSTATION (C) 24"D x 48"W and Smaller Surfaces Without Side Dividers Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). (D) 24"Dx48"W and Smaller Surfaces With Side Dividers If using side dividers, frame will include arm brackets BHA19. Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). BHA19 Brackets 6 WORKSTATION (E) 24"D x 54"72"W Surfaces Without Dividers Extend the frame equal to the surface width. Center arm brackets in reference to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). (F) 24"D x 54"72"W Surfaces with Side Dividers If using side dividers, inset the frame 2" from each end. Center arm brackets to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). Note: If using side dividers AND a facing divider with BSBHL, replace the arm brackets with BHA19. 2" 2" 7 END OF WORKSTATION SECTION (G) 30" Deep Surfaces Extend the frame equal to the surface width. Center arm brackets to surface depth. Secure frame to surface using wood screws (B) and secure handset using wood screws (C). 5 | Secure Power Cord & Install Feet Secure power cord to the control box. Secure locking screws on the adjustable beam and install the feet using screws (D) for each leg. If workstation is complete, flip over. Reference handset guide for initialization and operation functions. Note: Use T-feet if using T-arm brackets. 8 A1: Casters Overview THINK Height-Adjustable Workstation All parts listed are for a set of 4 casters; additional parts will be needed for additional casters. 9 CASTERS Parts List Code Qty. Description 1 Caster Kit (Set of 4) BHACAST 16 Screws 10 CASTERS 1 | Remove Glides From Feet Unscrew all four glides from feet and disregard. 11 END OF CASTERS SECTION 2 | Attach Casters to Feet The workstation's feet have pre-drilled holes for the caster plate. Attach casters using self-tapping metal screws. 12 A2: Modesty Panel Overview THINK Height-Adjustable Workstation All parts listed are for a single modesty panel; additional parts will be needed for additional modesty panels. 13 MODESTY PANEL Parts List Code Qty. Description 1 Laminate Modesty Panel* GLMP## 4 Machine Screws BMPBFB 2 L-Brackets 4 Wood Screws *For Steel Modesty Panel: components may vary, but process is similar. 14 MODESTY PANEL 1 | Secure Brackets to Modesty Panel Connect the BMPBFB bracket to the modesty panel using screws. Secure tightly. 15 END OF MODESTY PANEL SECTION 2 | Attach Modesty Panel to Surface Attach modesty panel to surface using wood screws provided with brackets. Panel will be center aligned and flushed with back of surface. 16 A3: Slim Pedestal Overview THINK Height-Adjustable Workstation All parts listed are for a single slim pedestal; additional parts will be needed for additional slim pedestals. 17 SLIM PEDESTAL Parts List Code Qty. Description 1 Large Mounting Bracket BFSLM.SM 1 Small Mounting Bracket BFSLM 1 Slim Pedestal 8 BFSLM.HW 10 Machine Screw Wood Screw 18 SLIM PEDESTAL 1 | Secure Brackets to Slim Pedestal Align large mounting bracket to front of pedestal and align small mounting bracket to back. Secure both brackets using provided screws. 19 END OF SLIM PEDESTAL SECTION 2 | Attach Slim Pedestal to Surface Secure pedestal to surface using wood screws. The pedestal brackets will connect on either side of the center beam. 20 A4: Cable Tray Overview THINK Height-Adjustable Workstation All parts listed are for a single cable tray; additional parts will be needed for additional cable trays. 21 CABLE TRAY Parts List Code BHCT Qty. Description 1 Surface-Mount Cable Management Tray 10 Wood Screws 22 CABLE TRAY 1 | Extend Cable Tray to Desired Length Extension range: 25"45". 23 END OF CABLE TRAY SECTION 2 | Attach Cable Tray to Surface Attach cable tray using wood screws. 24 1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com © 2023 Juniper Office | Version 23.0.0