Bambu Lab A1 mini 3D Printer: Disclaimer and Safety Guidelines

This document provides essential information regarding the safe operation, installation, and maintenance of your Bambu Lab A1 mini 3D Printer. Please read carefully before use.

Product Information

Product Name: Bambu Lab A1 mini 3D Printer

Model Number: PF002-M

Manufacturer: Shenzhen Tuozhu Technology Co., Ltd. (Bambulab USA Inc)

Material: 80g matte coated paper

Process: Die-cutting, single-color spot color printing

PANTONE Color: 447 C

Disclaimer and Warning

Thank you for purchasing a Bambu Lab product. The information in this document affects your safety and legal rights. Failure to follow instructions may result in serious injury, damage to the product, or other property. Bambu Lab accepts no liability for damage or injury incurred indirectly or directly from the use of the product. By using this product, you agree to use it only for proper purposes and in accordance with all applicable laws and guidelines provided by Bambu Lab.

Note: Bambu Lab is a trademark of Shenzhen Tuozhu Technology Co., Ltd. Other product and brand names are trademarks of their respective owners.

Before You Start

Ensure you have all included parts. Review the Quick Start Guide before operating the printer. Contact Bambu Lab or an authorized dealer if you have questions or problems during installation, maintenance, or use.

Safety Guidelines

Use by trained, knowledgeable, and experienced personnel only.
Disconnect power before installation or maintenance.
Connect to a grounded mains socket outlet.
Installation and maintenance must be performed by a skilled worker following manufacturer instructions and local safety regulations.
Do not use multiple plug adapters or extension leads.
Do not touch the product with wet body parts or operate while barefoot.
Do not reach inside the appliance while it is in operation.
Keep out of reach of children.
For indoor use only; keep in a dry environment.
Recommended operating temperature: 10°C to 30°C (50°F-86°F).
Recommended humidity level: under 85%.
Recommended operating altitude: less than 2000m.
Position on a clean, stable, and flat workbench.
Keep in a well-ventilated location.

Compliance Information

FCC Compliance Notice

Supplier's Declaration of Conformity

Product Name: A1 mini

Model Number: PF002-M

Responsibility Party: Shenzhen Tuozhu Technology Co., Ltd. (Bambulab USA Inc)

Address: 8000 Centre Park Drive, STE 330, Austin, TX, 78754

Website: www.bambulab.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try to correct it by reorienting the antenna, increasing separation, connecting to a different circuit, or consulting a dealer.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits for an uncontrolled environment. Install and operate with a minimum distance of 20cm between the radiator and your body.

ISED Compliance Notice

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation.

French Translation: Cet appareil contient un (s) émetteur (s) / récepteur (s) exempté (s) de licence (s) conforme à l'innovation, à la science et au développement économique Canada exempte (s) RSS (s). L'opération est soumise aux deux conditions suivantes: (1) Cet appareil peut ne pas causer d'interférence. (2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant entraîner un fonctionnement indésirable de l'appareil.

ISED Radiation Exposure Statement: The device meets exemption from routine evaluation limits in section 2.5 of RSS-102 and compliance with RSS-102 RF exposure. Users can obtain Canadian information on RF exposure and compliance. Install and operate with a minimum distance of 20 centimeters between the radiator and your body.

French Translation: Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

EU Compliance Statement

Shenzhen Tuozhu Technology Co., Ltd. declares that the radio equipment type A1 mini is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.bambulab.com/euro-compliance

UK Compliance Statement

Shenzhen Tuozhu Technology Co., Ltd. declares that the radio equipment type A1 mini is in compliance with Radio Equipment Regulations 2017. The full text of the GB declaration of conformity is available at: www.bambulab.com/euro-compliance

Safety Symbols:

DANGER ELECTRIC SHOCK ⚡
KEEP HANDS CLEAR OF MOVING PARTS ✋
DO NOT TOUCH NOZZLE OR BED WHILE HOT ?

Certifications: FC, CE, RoHS, UKCA

Model Identifier: 214-230198