2000W Pure Sine Wave Inverter with ATS and RCD
“
Specifications:
- Output Power: 3000W
- Input Voltage: 12V DC
- Output Voltage: 240V AC
Product Overview:
The iTechworld Inverter range was designed to convert 12V power
from a battery system into safe and reliable 240V power. This
allows operation of appliances typically used at home from a
caravan, camper, or 4WD.
Key Features:
- MOUNTING BRACKETS for easy installation
- CHASSIS GROUND for safety
- COOLING FAN for temperature regulation
- REMOTE PORT for remote control (remote sold separately)
Installation:
AC Output Installation:
Recommendation: It is advised to have a
licensed electrician perform this installation.
Before installing the inverter, ensure it is switched off and no
devices are connected to the AC 240V outputs.
Chassis Grounding:
Properly ground the inverter chassis according to local
electrical codes and regulations for safety.
Connecting the Battery:
- Ensure correct cable sizes and fuses are used.
- Remove plastic covers from inverter terminals.
- Loosen screws on terminal covers and slide them over the
leads. - Remove nuts and washers from inverter terminals.
Operation:
To operate the inverter, follow these steps:
- Ensure the inverter is connected to a properly sized
battery. - Turn on the inverter using the POWER SWITCH.
- The LED INDICATORS will show the status of the inverter.
Safety Precautions:
Ensure to follow all safety precautions mentioned in the user
manual to prevent accidents or damage to the inverter or connected
devices.
Contact Us:
If you have any questions or need assistance, please contact our
service center listed in the user manual.
Frequently Asked Questions (FAQ):
Q: What should I do if the Fault LED flashes once?
A: Isolate the inverter for 60 seconds, ensure the input voltage
is between 10.5V – 15.5V.
Q: How do I handle an AC Output Short Circuit Detected
fault?
A: Isolate the inverter, inspect your appliance, then reconnect
the appliance.
Q: What should I do if the inverter shows an Internal Fault
Detected error?
A: Isolate the inverter, then reconnect the appliance. If issues
persist, contact iTechworld service center.
“`
USER GUIDE
INVERTER
PURE SINE WAVE
1
CONTENTS
1. Overview
3
Key Features
3
Product Overview
3
Remote Overview (Sold Separately)
5
LED Indicators
6
Fault LED Indicators
6
2. Installation
7
AC Output Installation
7
Chassis Grounding
8
Connecting the Battery
8
Basic Setup Diagram
9
Remote Installation
10
Mounting Requirements
11
Cable & Fuse Guide
12
Battery Preparation
13
3. Operation
14
Operating the Inverter
14
AC 240V Output Overview
15
4.
16
5. Safety Precautions
17
6. Contact Us
Back Page
2
OVERVIEW
The iTechworld Inverter range was designed and developed to convert your 12V power from your battery system into safe and reliable 240V power. This allows you to operate appliances you’d typically have to stay at home to use, from the comfort of your caravan, camper, or 4WD.
KEY FEATURES:
· Pure Sine Wave Output
· Optional Remote
· Virtually Silent
· Lower Total Harmonic Distortion
· Extensive Internal Safety Features
PRODUCT OVERVIEW:
3000W
OUTPUT SIDE INPUT SIDE
MOUNTING BRACKETS CHASSIS GROUND
3
POSITIVE TERMINAL NEGATIVE TERMINAL COOLING FAN 240V OUTPUT PORT
POWER SWITCH LED INDICATORS REMOTE PORT
4
REMOTE OVERVIEW (SOLD SEPERATELY):
FAULT POWER
BATTERY LOAD
20% 40% 60% 80% 100%
The inverter remote provides you with the ability to control the inverter’s basic features from a more convenient location. For the remote to function, the on/off switch on the inverter must be turned on.
POWER BUTTON Press and hold for 3 seconds to turn the inverter on/off.
FAULT LED
Illuminated when the inverter encounters a fault.
POWER LED
Illuminated when theinverteris onand flashes when inverteris off.
BATTERY VOLTAGE The battery voltage is based on the DC input voltage.
LOAD DISPLAY
The load display is based on the current inverter load.
5
LED INDICATORS:
Status Standby In Use
Fault
Power LED Flashing
ON ON
LED Light
Fault LED Flashing
OFF Flashing
FAULT LED INDICATORS:
Fault LED Flashes Once
Fault
Over / Under Voltage Protection Activated
Solution
Isolate the inverter for 60 seconds, ensure the input voltage is between 10.5V – 15.5V.
Flashes Twice
AC Output Short Circuit Detected
Isolate the inverter, inspect your appliance, then reconnect the appliance.
Flashes 3 Times
Over / Under Temperature Protection Activated
Isolate the inverter, ensure the temperature is within -10°C and 50°C.
Flashes 4 Times
AC Output Overload Detected
Isolate the inverter and ensure the total draw of your appliance/s does not exceed
the rated maximum of the inverter.
Flashes 5 Times Internal Fault Detected
Isolate the inverter, then reconnect the appliance. If you are still experiencing issues, please contact the iTechworld
service centre.
6
INSTALLATION
AC OUTPUT INSTALLATION:
WE RECOMMEND THIS INSTALL IS DONE BY A LICENSED ELECTRICIAN Before installing the inverter into your system, ensure the unit is switched off and that there are no devices plugged into the AC 240V outputs.
THIS STEP SHOULD BE COMPLETED BEFORE INSTALLATION 7
CHASSIS GROUNDING:
Grounding of the inverter is mandatory before use to prevent damage or injury. Locate the grounding point on the provided mounting bracket near the negative terminal of the inverter. Ground the inverter by securely attaching a copper cable which is at least 4mm 2. Connect the other end of the mentioned copper cable to a suitable earthing point, such as your vehicles frame or the grounded negative terminal of the battery. Please consult a licensed electrician to ensure your application meets Australian / New Zealand standards.
CONNECTING THE BATTERY:
1 – Before connecting the inverter to a battery, ensure you have the correct cable sizes and fuses. 2 – Begin my removing the plastic inverter terminal covers, loosen the screws at on the top and bottom of the terminal covers to remove them. Slide these covers over the leads you’ll be using to connect to the inverter. 3 – Remove the nuts and washers from the inverter terminals.
4 – Attach the positive and negative cable to their respective input terminal. Thread the cable eye and washer over the bold, then secure it with a nut to ensure a tight connection, repeat this step for both sides. 5 – Reinstall the inverter terminal covers. 6 – Connect the positive and negative inverter cables to the battery or DC power source. First, attach the positive terminal, followed by the negative terminal.
Ensure the positive lead has an appropriately sized and placed fuse for added safety.
8
BASIC SETUP DIAGRAM:
BM500
MAXI FUSE
BUSBARS FOR WIRING ACCESSORIES (OPTIONAL)
MAXI FUSE
9
REMOTE INSTALLATION (SOLD SEPARATELY):
The remote allows the inverter to be operated from a distance, making it perfect for installations where the inverter is not easily accessible. 1 – Select a space you would like the inverter remote to be installed, preferably away from moisture in a canopy or caravan wall. 2 – Refer to the mounting diagram below for the dimensions of the hole you will have to make. 3 – Drill 2mm holes on the designated mounting points and cut a hole in the mounting surface according the diagram above.
86mm 60mm
10
86mm 60mm
4 – Remove the faceplate of the inverter remote by pulling on the small recess along one of the outer edges. 5 – Insert the remote into the prepared hole and secure it in place using M3 screws
6 – Reattach the inverter remote faceplate and connect the included RJ12 cable to the core
MOUNTING REQUIREMENTS:
When mounting the inverter, please adhere to the following guidelines: VENTILATION – Provide at least a 100mm space around the inverter to prevent heat build up.
ORIENTATION – ldeally, mount the inverter horizontally on a flat surface. Vertical mounting is ok however this may put stress on the circuit board. Do not mount the inverter upside down (with the base facing up). STABLE – Ensure the inverter is mounted on a sturdy surface capable of supporting its weight, utilising all of the mounting points with the correct fasteners. DRY – Mount the inverter in an area free from moisture.
11
COOL – Opt for a mounting location that stays within 0°C and 40°C. SAFE – Ensure the mounting area is free from fumes and other potential hazards. LIMIT DUST – Mount the inverter in an area with minimal dust ingress to prevent dust from being drawn in my the fans during operation. ELECTRICAL – Position the inverter close to the battery to minimise voltage drop. Maintain a distance of at least 300mm between the inverter and the battery. Install a fuse on the positive cable between the inverter and the battery, placing the fuse close to the battery end to protect the cable.
CABLE & FUSE GUIDE:
The cable between the inverter and battery must be thick enough to prevent voltage drop. Since voltage drop happens between the battery positive and ground, the total length of both cables must be considered. NOTE: The cables should be routed in a way that reduces the risk of damage. Consider using cable conduit or protective tubing to mitigate this risk to ensure
+ MAXI FUSE
12
LENGTH 0-1M 1-2M 2-3M
MODEL FUSE SIZE
2000W 70mm² (2/0) 70mm² (2/0) 90mm² (3/0)
SIZE (AWG)
3000W 90mm² (3/0) 90mm² (3/0) 120mm² (4/0)
2000W 250A
3000W 450A
BATTERY PREPARATION:
Before installing your inverter, it is essential to verify your batteries are 12v and is one of the following chemistries: SLD, AGM, GEL, or LiFeP04. The inverters are also capable of being connected to batteries in parallel. Paralleling an iTechworld battery with a compatible iTechworld battery of the same Ah and type will increase the maximum continuous discharge rate.
MODEL MAX CONSTANT AMP DRAW
2000W 185A
3000W 278A
DEEP-CYCLE BATTERY DEEP-CYCLE BATTERY
MAXI FUSE SHUNT BM500
13
OPERATION
OPERATING THE INVERTER:
Once you’ve wired the input side, your inverter is ready to power your 240V appliances. Before operating the inverter, ensure the total wattage of the appliance/s you intend to use is below the rated wattage of the inverter.
1 – If you’re powering the inverter from an 12V source, ensure that the battery has enough charge to support the draw.
2 – Plug the appliance into the AC 240V output.
3 – Turn on the inverter.
4- Turn on your appliance/s.
240V SOCKETS
APPLIANCES
+ MAXI FUSE
14
AC 240V OUTPUT OVERVIEW:
AC 240V OUTPUT
Each inverter is equipped with standard Type I AC 240V sockets for appliances. You have the option to directly plug the appliance into the inverter or use a power board to power multiple appliances simultaneously.
It is important to note you can only connect appliances with a wattage the same or below the rated max of the specific inverter.For instance, iTechworld 300OW inverter has a maximum continuous output of 3000W. So you will have to ensure the combined wattage of all the connected devices does not exceed 3000W.
MODEL 2000W 3000W
AC OUTPUT INTERFACE 10A Type I 15A Type I
15
SPECIFICATIONS
Model Name Max Continuous Output Peak Output Battery Type Compatibility Input Voltage Range Output Plug Rating Output Voltage & Current No Load Draw
Output Waveform
IP Rating Operating Temperature Storage Temperature Dimensions
Safety Features
General
2000W
3000W
2000W
3000W
4000W
6000W
SLD, AGM, GEL, or LiFeP04.
10.5V – 15.5V
10A
15A
240V ~ 50Hz
<1.3A
<1.6A
89%~92%
Pure Sine Wave
<3%
IP22
-10°C-50°C
-30°C-70°C
440 x 265 x 97mm
494 x 289 x 105mm
Protections
15.5±0.2V DC 10.5±0.2V DC
Terminal Dimensions
Remote
RJ12 86 x 86 x 19mm
The iTechworld Inverter Range comply with AS/NZS 4763:2011 and IEC/EN 62368-1 including Australian deviations.
16
SAFETY PRECAUTIONS
For safe operation and optimal performance, the iTechworld Pure Sine Wave Inverter must be installed and operated correctly. Please carefully read, understand, and follow all instructions and guidelines in this user guide.
Pure Sine Wave Inverter. Failure to follow these instructions may result in damage to the unit, property, death, or serious injury.
Disclaimer: While iTechworld has taken every precaution to ensure the accuracy of the contents of this user guide, iTechworld assumes no responsibility for any errors or omissions.
without notice.
WARNING: This inverter generates AC 240V power which may cause death or severe injury. Even with the inverters advanced internal safety features, caution should be used when operating the unit.
WARNING: People with physical disabilities, visual, sensory, or mental impairments (including children) should not use this inverter. Children should be supervised to ensure they do not play with Inverters.
WARNING: Please use the fuses and wires recommended in this user guide, otherwise, it may
WARNING: Ensure the continuous output of this inverter does not exceed the battery’s recommended discharge rate. If you are unsure of the recommended discharge rate, please consult your battery’s manufacturer.
17
DANGER: Do not disassemble or modify the inverter, doing so may result in a risk of DANGER: This inverter is only suitable for battery types listed in the user guide. Do not use it for other purposes. DANGER: Do not connect the inverter with reverse polarity, as doing so may result in a risk EXPLOSION HAZARD: (such as gas bottles). LIMITATIONS OF USE: Do not use in connection with life support systems or other medical equipment / devices.
18
CONTACT US
1300 483 249
service@itechworld.com.au
www.itechworld.com.au
When it comes to energy storage and creation at iTechworld, we take pride in being one of the biggest names in the industry. Based in Australia, we are a family-owned and operated business. With many more innovative products on the horizon we are committed to constantly raising the bar to provide bigger and better benefits to all our customers Australia-wide.
Whether you’re an avid camper, 4WD enthusiast , freedom seeker or camper, we’ve got your power needs covered. Escape the grid without compromise, minimise your downtime and travel with comfort with our large range of leading products at great prices. iTechworld. The Power Expert.
LOVE YOUR iTECHWORLD INVERTER? LEAVE A REVIEW
Documents / Resources
 |
iTECHWORLD 2000W Pure Sine Wave Inverter with ATS and RCD [pdf] User Guide 2000W Pure Sine Wave Inverter with ATS and RCD, 2000W, Pure Sine Wave Inverter with ATS and RCD, Wave Inverter with ATS and RCD, ATS and RCD |