iSkydance V1-SP RF Dimming LED Controller User Guide

Connect the RF Dimming LED Controller to the power supply
according to the wiring diagram provided.
Mount the controller securely using the installation rack.

Connect the LED strip to the output terminals of the
controller.

Matching with RF Remote Control:

Match Key:

To match, short press the match key on the controller and then
immediately press the on/off key (for single-zone remote) or zone
key (for multi-zone remote) on the remote control.
The LED indicator will fast flash to indicate a successful
match.

Power Restart:

To match, switch off the power and then switch it back on.
Repeat the process and immediately short press the on/off key (for
single-zone remote) or zone key (for multi-zone remote) three times
on the remote control.

The output light will flash three times to indicate a
successful match.

Delete Matched Remotes:

Press and hold the match key for 10 seconds to delete all
matched remotes. The LED indicator will fast flash to confirm
deletion.

Frequently Asked Questions (FAQ):

Q: What is the input voltage range for the RF Dimming LED
Controller?

A: The input voltage range is 12-48VDC.

Q: How many remote controls can be paired with one RF
controller?

A: One RF controller can accept up to 10 remote controls.

Q: What are the available dimming curves for this
controller?

A: The available dimming curves are Linear and Logarithmic.

Q: How can I delete all matched remotes from the
controller?

A: Press and hold the match key for 10 seconds to delete all
matched remotes. The LED indicator will fast flash to indicate
deletion.

“`

View Fullscreen

V1-SP
RF DimmingLED Controller

RFDIM

Mini RF dimming single channel constant voltage LED controller. Match with RF 2.4G single-zone or multi-zone dimming remote controller optional. One RF controller accept up to 10 remote control. 4096 levels 0-100% dimming smoothly without any ash. Logarithmic or linear dimming curves are available. 500Hz, 2KHz, 8KHz or 16KHz output PWM frequency selectable. Connect with external push switch to achieve on/off,
and brightness 0-100% adjustment function. Overheat/reverse/short circuit protection. 3s on/off fade can be set.

Technical Parameters

Input and Output

Dimming data

Input voltage

12-48VDC

Input signal

RF 2.4GHz + Push-DIM

Output voltage Output current
Output power

12-48VDC 6A@12/24V 5A@36/48V
72W@12V 144W@24V 180W@36V 240W@48V

Control distance Dimming gray scale Dimming range Dimming curve

30m(Barrier-free space) 4096 (2^12)levels 0 -100% Linear/Logarithmic

Environment

PWM frequency 500Hz/2KHz/8KHz/16KHz

Operation temperature Case temperature (Max.) IP rating

Ta: -20 OC ~ +55OC Tc: +73OC IP20

Warranty and Protection

Warranty Protection

5 years Anti-reverse, overheat short circuit

Safety and EMC
EMCstandard Safety standard Radio equipment
Certification Package Size Gross weight

EN IEC 55015/ EN IEC 61547-1/-2 ETSI EN 301 489-1/-17 EN 61347-1/-2 ETSI EN 300 328 ETSI EN 300 440 CE RoHs
L60 x W60 x H40mm 0.043kg

38.50mm

Mechanical Structures and Installations

LED indicator

RF antenna Installation rack
Push switch input

V1-SP
RF LED Dimmer Uin = 12-48VDC

SET tc: 73 PWM Freq

Uout= 12-48VDC

Iout = 6A@12/24V 5A@36/48V

2.4G

Temp Range: -20~+55

16KHz 8KHz 12 12
2KHz 500Hz

0.5-2.0mm²

6-7mm

INPUT

V- V+

OUTPUT LED+ LED-

1 2 1 2 ON Dim Curve
linear log

Match Key
5.00mm DIP Switch setting

Power input Power input + LEDoutput+

LEDoutput-

Note: The mounting ear on both sides can be broken along the indentation, to suit different mounting needs.
User Manual Ver 1.0.0 2025.7

56.00mm 42.50mm
50.00mm 56.00mm

18.00mm

Wiring Diagram

DIMremote

Push Switch

SET
PWM Freq 16KHz 8KHz

12 12 2KHz 500Hz

1 2 1 2 ON Dim Curve
linear log

AC100-240V

Power Supply 12-48VDC
Constant Voltage

+ Single color LED strip
–

Wire preparation: 1. The wiring can be solid or stranded with a cross-sectional area of 0.5 to 2.0 mm².
Conventional 1mm² can withstand 10A output current. 2. When wiring is installed, the terminals must be tightened. If they are not tightened, the contact point resistance will be too high
and the terminals will easily burn due to heat when used at full load for a long time. Note: The output power of a constant voltage power supply should be at least 1.2 times that of the output load (LED strip), otherwise the full power output of the load can easily cause automatic flickering or shaking of the light.

Match with RF Remote Control

There are two ways to match/delete:
Use match key
Match: Short press match key, enter the match state. immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote, The LED indicator fast flash means match is successful.

Use Power Restart
Match: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The output light flashes 3 times means match is successful.

Delete: Press and hold match key for 10s to delete all match, The LED indicator fast flash means all matched remotes were deleted.
Push Switch Dimming

Delete: Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The output light flashes 5 times means all matched remotes were deleted.

The push switch interface can be connected to push panel switch or push button for dimming.
Short press: Turn the light on or off. Double-click: Switch between 10% and 100% brightness. Long press(1-6s): Continuously increase or decrease the brightness,
long press again after each release, the brightness changes in the opposite direction. Dimming memory: The brightness value has been set by long-pressing Push, with power-down memory. Synchronize: If multiple controllers are connected to the same self-reset switch,
please long press for 10s first to synchronize all lights to 100% brightness. It is recommended that the number of controllers connected to the same push switch does not exceed 25, and the length of the connecting wire does not exceed 20m.

Page 1-2

PWM Frequency Setting

12 12 12 12
500Hz 2KHz 8KHz 16KHz

Four PWM frequencies can be selected: 500Hz, 2KHz, 8KHz or 16KHz. Higher PWM frequency will result in lower output current, higher power supply noise, more suitable for camera shooting (video without flicker).

PWM duty(%) PWM duty(%)

Dimming Curve Setting

Linear Dimming Curve

110000 9900 8800 7700 6600 5500 4400 3300 2200 1100

Gamma=1.0

10 20 30 40 50 60 70 80 90 100

Brightness(%)

Logarithmic Dimming Curves

100
Gamma=1.6
90 80 70 60 50 40 30 20 10

10 20 30 40 50 60 70 80 90 100

Brightness(%)

On/Off Fade Time Setting
Press and hold the match key for 10s to restore the default parameters, factory default parameters: light on/off fade time is 0.5s. Press and hold the match key for 15s, the light on/off fade time is set to 3s.

Installation Precautions
1. The products shall not be stacked, the distance should be 20cm, so as not to affect lifespan of the products due to poor heat dissipation.
2. The product shall not be installed close to the switching power supply with an interval of 20cm to avoid radiation interference of the switching power supply.
3. The installation height shall be 1m from the oor to avoid shortening remote control distance due to too weak reception signal. 4. The products are not allowed to be close to or covered by metal objects, with an interval of 20cm to avoid signal attenuation
and shorten the remote distance. 5. Avoid installation at the corner of the wall or the corner of the beam, with an interval of 20cm to avoid signal interference.

User Manual Ver 1.0.0 2025.7

Page 3-4

Documents / Resources

iSkydance V1-SP RF Dimming LED Controller [pdf] User Guide
V1-SP RF Dimming LED Controller, V1-SP, RF Dimming LED Controller, Dimming LED Controller, LED Controller

References

User Manual

iSkydance V1-SP RF Dimming LED Controller User Guide

V1-SP RF Dimming LED Controller

Product Specifications:

Product Usage Instructions:

Installation: