R1 snjall hreyfiskynjari
“
Tæknilýsing
- Name: Smart Motion Sensor R1
- Gerð: R1
- Stærðir: N/A
- Operation Voltage: N/A
- Gerð rafhlöðu: N/A
- Vinnutíðni: N/A
- Working Condition: N/A
- Vinnuhitastig: Ekki til staðar
Vörulýsing
The Smart Motion Sensor R1 is a wireless motion sensor designed
to detect movement within a specific range. It features adjustable
sensitivity levels and LED indicators to provide real-time feedback
on motion detection.
Notkunarleiðbeiningar fyrir vöru
Uppsetning
- Open the battery cover and remove the insulation strip to power
á tækinu. - If not in pairing mode, press and hold the + button for 10
seconds to factory reset. - Follow platform instructions to add the device.
Using Case
- Place the sensor in a suitable location away from interference
heimildum. - Adjust sensitivity level (1-5) based on sensing distance.
- Set up routines on the platform using the sensor as a
kveikja.
Uppsetning
The sensor can be placed on a table or mounted on a wall using
skrúfur.
- Lóðrétt sett á borð
- Hangið á vegginn
Úrræðaleit
To optimize detection accuracy:
- Avoid installing on metal surfaces; use insulating layers if
nauðsynlegar. - Keep the sensor away from strong signal fields of other
þráðlaus tæki. - Avoid placing multiple sensors with detection surfaces opposite
hvert annað.
Algengar spurningar
Q: How do I adjust the sensitivity level of the R1 sensor?
A: The sensitivity level can be adjusted by pressing the +/-
buttons on the device. Refer to the user manual for specific
instructions on changing sensitivity levels.
Q: Can I use the R1 sensor with platforms other than those
skráð?
A: The R1 sensor is compatible with platforms such as Amazon
SmartThings, Home Assistant, Hubitat, ThirdReality, Homey, and
Aeotec. For optimal functionality, it is recommended to use with
these supported platforms.
“`
Snjall hreyfiskynjari R1
Flýtileiðarvísir
Vörulýsing
The THIRDREALITY Motion Sensor R1 is the perfect companion for a smarter, more secure home. Seamlessly integrating with popular Zigbee hubs like Echo devices with built-in Zigbee hubs, SmartThings, and Home Assistant, it fits effortlessly into your existing setup. Imagine customizing its detection range from 1.5 to 9.5 meters to monitor your living room, hallway, or office just the way you need. With three AA batteries, the sensor delivers long-lasting performance up to 3 years in typical use, so you can focus on what’s important without constant maintenance. Set up routines via compatible apps to turn on lights as you enter a room or receive instant alerts when motion is detected, adding convenience and peace of mind. Whether placed discreetly on a shelf or mounted on a wall, the Motion Sensor R1 adapts to your space, keeping your home connected and secure.
Tæknilýsing
Name Model Dimensions Operating Voltage Battery Type Working Frequency Working Condition Working Temperature Range
Smart Motion Sensor R1 3RSMR01067Z 2.56 inch×1.18 inch×2.56 inch DC 4.5V AA battery × 3 (included) Zigbee 3.0 : 2.4GHz, Radar : 5.8GHz Indoor Use Only Default 0~40 (indoor)
Detect Level & Range
Stig 1 2 3 4 5
Range (m/inch) 1.5 / 59 3.5 / 138 5.5 / 217 7.5 / 295 9.5 / 374
01
Hnappar virka
Reset (+) LED (-)
Function Reset Indication Enhance sensitivity En/Disable motion detect light Decrease sensitivity
Procedure Press and hold for 10 seconds Click once Press and hold for 3 seconds Click once
LED staða
Operation Factory Reset Pairing Motion detected
Offline Low Battery
Description The LED is illuminated. The LED flashes rapidly. When the device is triggered, the indicator light for the current sensitivity level will illuminate for 1 second. The LED flashes once every 3 seconds. The LED flashes twice every 5 seconds.
*The sensitivity indicator light will be reused with the status indicator light.
02
03
Uppsetning
1. Open the battery cover on the device and remove the insulation strip to power the device.
2. When the device is powered on, the sensitivity indicator will flash rapidly and the device will enter the Zigbee pairing mode. If the sensor is not in the pairing mode, press and hold the + button for 10 seconds to factory reset the sensor.
3. Follow the instructions on the platform to add the device.
Samhæfðir pallar
Platform Amazon SmartThings Home Assistant Hubitat ThirdReality Homey Aeotec
Requirement Echo with built-in Zigbee hub 2015/2018 models, Station ZHA and Z2M with Zigbee dongle With Zigbee hub Smart Hub/Smart Bridge MZ1 Homey Bridge/Pro Aeotec Hub
04
Using Case
1. Hang or place the R1 sensor in a suitable and sturdy location. This location should be away from the wireless router and places where there may be slight vibrations (such as washing machines). If there are multiple R1 sensors, avoid overlapping sensing areas to cause false alarms.
2. After completing the installation, you should first adjust the sensor’s sensitivity. There are 5 sensitivity levels from low to high, represented by numbers 1-5. Please try the sensing distance from level 3 (The default is level 3). If the sensing distance is too close, you can switch to a higher level, otherwise you should adjust to a lower level. The sensitivity and LED indicator switch can only be adjusted on the device.
3. Start setting the routine. The R1 sensor is the same as the Wireless Motion sensor. You can select the R1 sensor as the trigger on the platform, and then set some switches or devices as reactors. When the device is triggered, the indicator light for the current sensitivity level will illuminate for 1 second.
05
Uppsetning
Varan er með hálkuvörn, sem gerir það kleift að setja hana beint á borð eða festa hana á vegg með skrúfum.
Sylgjur
1 Vertically placed on table
2 Hang on the wall 06
Úrræðaleit
To achieve the desired detection accuracy: Do not install the sensor on a metal surface. If you need to install it, please place a non-metallic insulating layer (e.g. plastic or rubber pad, >5mm thick) between the radar and the metal surface. When installing the sensor, please keep it at least 1m away from other wireless devices that will create a strong signal field (e.g. Wireless router). When installing multiple radar sensors, do not place the detection surfaces opposite each other.
Skannaðu QR-kóðann til view smáatriði
https://bit.ly/3PdGajZ 07
Samræmi við FCC reglugerðir
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.
Breytingar eða breytingar sem ekki hafa verið samþykktar sérstaklega af þeim aðila sem ber ábyrgð á samræmi gæti ógilt heimild notanda til að nota búnaðinn.
ATHUGIÐ: Þessi búnaður hefur verið prófaður og reynst vera í samræmi við takmarkanir fyrir stafrænt tæki í flokki B, samkvæmt 15. hluta FCC reglnanna. Þessi mörk eru hönnuð til að veita eðlilega vörn gegn skaðlegum truflunum í íbúðarhúsnæði. Þessi búnaður framkallar notkun og getur geislað út radíótíðniorku og, ef hann er ekki settur upp og notaður í samræmi við leiðbeiningarnar, getur hann valdið skaðlegum truflunum á fjarskipti. Hins vegar er engin trygging fyrir því að truflun eigi sér stað í tiltekinni uppsetningu. Ef þessi búnaður veldur skaðlegum truflunum á útvarps- eða sjónvarpsmóttöku, sem hægt er að ákvarða með því að slökkva og kveikja á búnaðinum, er notandinn hvattur til að reyna að leiðrétta truflunina með einni eða fleiri af eftirfarandi ráðstöfunum:
08
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help important announcement. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Yfirlýsing um útsetningu fyrir geislun
Þessi búnaður er í samræmi við geislaálagsmörk FCC sem sett eru fram fyrir óviðráðanlegt umhverfi. Þessi búnaður ætti að vera settur upp og notaður með lágmarksfjarlægð 20 cm á milli ofnsins og líkamans. Þessi sendir má ekki vera staðsettur samhliða eða virka í tengslum við önnur loftnet eða sendi.
09
ISED yfirlýsing
Þetta tæki er í samræmi við Innovation, Science and Economic Development Canada RSS-staðla sem eru undanþegnir leyfisskyldu. Rekstur er háður eftirfarandi tveimur skilyrðum:
(1) þetta tæki má ekki valda truflunum og (2) þetta tæki verður að sætta sig við hvers kyns truflun, þar með talið truflanir sem geta valdið óæskilegri notkun tækisins.
Le présent appareil est confrome aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accept tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Leysi í flokki sem er endurtekið ISED festa og umhverfis ekki stjórna. Uppsetning og vinnsla á materiel devrait með échangeur fjarlægð lágmarki entre 20 cm tonna corps.Lanceurs eða ekki peuvent sem sameinast samlífa antenne eða capteurs avec d'autres.
Takmörkuð ábyrgð
For limited warranty, please visit https://3reality.com/faq-help-center/ For customer support, please contact us at info@3reality.com or visit www.3reality.com For questions on other platforms, visit the corresponding platform’s application/support platform.
10
11
11
Skjöl / auðlindir
 |
THIRDREALITY R1 Smart Motion Sensor [pdfNotendahandbók R1_QSG_20250310, R1, R1 Smart Motion Sensor, R1 Motion Sensor, Smart Motion Sensor, Motion Sensor, Smart Sensor, Sensor |