INVENTRONICS LogoSUM-760SxxxMGR Rev.A
760W Programmable Driver with INV Digital Dimming

Features

  • INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital DimmingINVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - IconPanel Mount Connectors Facilitates Installation
  • Rotary Switch+RJ12 Connector
  • Hot-plugging Protection
  • Parallel LED Protection
  • Ultra High Efficiency (Up to 95.5%)
  • Full Power at Wide Output Current Range (Constant Power)
  • Adjustable Output Current (AOC) with Programmability
  • Isolated 0-10V/PWM/Resistor/3-Timer-Modes Dimmable
  • INV Digital Dimming, UART Based Communication Protocol
  • Dim-to-Off with Standby Power ≤ 0.5W
  • Minimum Dimming Level with 5% or 10% Selectable
  • Maximum Dimming Level with 9V or 10V Selectable
  • Fade Time Adjustable
  • Low Inrush Current
  • Output Lumen Compensation
  • End-of-Life Indicator
  • Input Surge Protection: DM 6kV, CM 10kV
  • All-Around Protection: IOVP, IUVP, OVP, SCP, OTP
  • IP66 and UL Dry/Damp/Wet Location
  • 5 Years Warranty

Description

The SUM-760SxxxMGR series is a 760W, constant-current, programmable and IP66 rated LED driver that operates from 90-305Vac input with excellent power factor. Created for many lighting applications including high mast, sports, UV-LED, aquaculture and horticulture, etc. It provides rotary switch, RJ12 connector and dim-to-off functionality. The dimming control supports 0-10V dimming as well as two-way communication via Digital Dimming, a UART based communication protocol. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure trouble-free operation,
protection is provided against input surge, input under voltage, input over voltage, output over voltage, short circuit, and over temperature.
Models

Adjustable Output Current Range

Full-Power
Current Range(1)
Default Output Current Input Voltage Range(2) Output Voltage Range Max Output Power Typical Efficiency (3) Typical Power Factor

Model Number

120Vac

220Vac

1.4-15.8A 14-15.8A 14 A 90~305Vac 127~300Vdc 34 ~54Vdc 760W 95.5% 0.99 0.96 SUM-760S15AMGR(4)

Notes:

  1. Output current range with constant power at 760W.
  2. Certified input voltage range: UL, FCC, CB 100-277Vac; otherwise: 100-240Vac
  3. Measured at 100% load and 220Vac input (see below “General Specifications” for details).
  4. SELV output

I-V Operating Area

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Fig

Input Specifications

Parameter Min. Typ. Max.

Notes

Input AC Voltage 90 Vac 305 Vac
Input DC Voltage 127 Vdc 300 Vdc
Input Frequency 47 Hz 63 Hz
Leakage Current 0.75 MIU UL 8750; 277Vac/ 60Hz
0.70 mA IEC 60598-1; 240Vac/ 60Hz
Input AC Current 7.54 A Measured at 100% load and 120 Vac input.
4.05 A Measured at 100% load and 220 Vac input.
Inrush Current(I2t) 1.87 A2s At 220Vac input, 25℃ cold start, duration=13.7 ms, 10%Ipk-10%Ipk. See Inrush Current Waveform for the details.
PF 0.90 At 100-277Vac, 50-60Hz,60%-100%Load (456-760W)
THD 20%
THD 10% At 220-240Vac, 50-60Hz,75%-100%Load (570- 60W)

Output Specifications

Parameter Min. Typ. Max.

Notes

Output Current Tolerance -5%Ioset 5%Ioset 100% load
Output Current Setting(Ioset Range) SUM-760S15AMGR 1400 mA 15800 mA
Output Current Setting Range with Constant Power SUM-760S15AMGR 14000 mA 15800 mA
Total Output Current Ripple (pk-pk) 5%Iomax 10%Iomax 100% load, 20 MHz BW
Output Current Ripple at < 200 Hz (pk-pk) 2%Iomax 70%-100% load
Parameter Min. Typ. Max.

Notes

Startup Overshoot Current 10%Iomax 100% load
No Load Output Voltage SUM-60S15AMGR 60 V
Line Regulation ±0.5% 100% load
Load Regulation ±3.0%
Turn-on Delay Time 0.5 s Measured at 120-277Vac input, 60%- 100% Load
Temperature Coefficient of Ioset 0.03%/°C Case temperature = 0°C ~Tc max

General Specifications

Parameter Min. Typ. Max.

Notes

Efficiency at 120 Vac input: SUM-760S15AMGR Io= 14000 mA Io= 15800 mA 91.5% 91.0%  

93.5% 93.0%


Measured at 100% load and steady-state temperature in 25°C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.)
Efficiency at 220 Vac input: SUM-60S15AMGR Io= 14000 mA Io= 15800 mA 93.5% 93.0% 95.5% 95.0%
Measured at 100% load and steady-state emperature in 25°C ambient;(Efficiency will be about 2.0% lower if measured immediately after startup.)
Efficiency at 277 Vac input: SUM-S15AMGRIo= 14000 mAIo= 15800 mA 93.5%93.5% 95.5% 95.5% – – Measured at 100% load and steady-state  emperature in 25°C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.)
Standby Power 0.5 W Measured at 230Vac/50Hz; Dimming off
MTBF 201,000 Hours Measured at 220Vac input, 80%Load and 25°C ambient temperature (MIL-HDBK- 217F)
Lifetime 102,000 Hours Measured at 220Vac input, 80%Load and 70°C case temperature; See lifetime vs. Tc curve for the details
81,000 Hours Measured at 220Vac input, 100%Load and 40°C ambient temperature
Operating Case Temperature for SafetyTc_s -40°C +90°C
Operating Case Temperature for Warranty Tc_w -40°C +80°C Case temperature for 5 years warranty Humidity: 10%RH to 95%RH
Storage Temperature -40°C +85°C Humidity: 5%RH to 95%RH
Dimensions Inches (L × W × H)illimeters (L × W × H) 15.35 × 4.25 × 1.91 390 × 108 × 48.5 With mounting ear 16.34 × 4.25 × 1.91 415 × 108 × 48.5
Net Weight 3500 g

Dimming Specifications

Parameter Min. Typ. Max.

Notes

Absolute Maximum Voltage on the Vdim (+) Pin -20 V 20 V
Source Current on Vdim (+)Pin 90 uA 100 uA 110 uA Vdim(+) = 0 V
Dimming Output Range with 10%-100% (Default) SUM-760S15AMGR 10%Ioset Ioset 14000 mA ≤ Ioset ≤ 15800 mA
SUM-760S15AMGR 1400 mA Ioset 1400 mA ≤ Ioset < 14000 mA
Dimming Output Range with5%-100% (Settable) SUM-760S15AMGR 5%Ioset Ioset 14000 mA ≤ Ioset ≤ 15800 mA
SUM-760S15AMGR 700 mA Ioset 1400 mA ≤ Ioset < 14000 mA
Recommended Dimming Input Range 0 V 10 V Default 0-10V dimming mode.
Dim off Voltage 0.35 V 0.5 V 0.65 V
Dim on Voltage 0.55 V 0.7 V 0.85 V
Hysteresis 0.2 V
PWM_in High Level 3 V 10 V Dimming mode set to PWM in Inventronics Programing Software.
PWM_in Low Level -0.3 V 0.6 V
PWM_in Frequency Range 200 Hz 3 KHz
PWM_in Duty Cycle 1% 99%
PWM Dimming off (Positive Logic) 3% 5% 8%
PWM Dimming on (Positive Logic) 5% 7% 10%
PWM Dimming off ( Negative Logic) 92% 95% 97%
PWM Dimming on ( Negative Logic) 90% 93% 95%
Hysteresis 2%

Safety &EMC Compliance

Safety Category

Standard

UL/CUL UL 8750,CAN/CSA-C22.2 No. 250.13
CE EN 61347-1, EN 61347-2-13
CB IEC 61347-1, IEC 61347-2-13

EMI Standards

Notes

EN 55015(1) Conducted emission Test &Radiated emission Test
EN 61000-3-2 Harmonic current emissions

EMI Standards

Notes

EN 61000-3-3 Voltage fluctuations & flicker
FCC Part 15(1) ANSI C63.4 Class B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired Operation.

EMS Standards

Notes

EN 61000-4-2 Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge
EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test-RS
EN 61000-4-4 Electrical Fast Transient / Burst-EFT
EN 61000-4-5 Surge Immunity Test: AC Power Line: Differential Mode 6 kV, Common Mode 10 kV
EN 61000-4-6 Conducted Radio Frequency Disturbances Test-CS
EN 61000-4-8 Power Frequency Magnetic Field Test
EN 61000-4-11 Voltage Dips
EN 61547 Electromagnetic Immunity Requirements Applies To Lighting Equipment

Note:

  1. This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself.

Derating

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating

Lifetime vs. Case Temperature

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating

Inrush Current Waveform

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 2

Efficiency vs. Load
SUM-760S15AMGR(lo=14000mA)

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 3

Power Factor

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 4

Total Harmonic Distortion

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 5

Hot-plugging Protection
This feature protects LEDs when connecting to a driver that is already powered on. This is disabled by default and can be enabled through the Inventronics Programing Software.
INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 6LED threshold voltage (Vth) is the minimum voltage required for current to flow through the LED load. After this threshold is met, the LED forward voltage (Vf) increases as the current increases.
Set Vth close to, but higher than the actual LED threshold voltage for optimized performance. The greater the difference between the Vth setting and the actual LED threshold voltage, the higher the overshoot current will be. The Vth setting must be lower than Vf. Please test, program, and tune this feature for each LED load design.

Parameter Min. Typ. Max.

Notes

 

Hot-plugging Protection

LED Threshold
Voltage Setting Range
44 V 54 V Set Vth close to, but higher than the actual LED threshold voltage
Setting Tolerance -2% 2%

Parallel LED Protection
This feature helps protect parallel LEDs from a high, overcurrent condition by limiting the voltage. This is disabled by default and can be enabled through the Inventronics Programing Software.

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 7

Set V_overload close to, but higher than the maximum forward voltage for optimized performance. The greater the difference between the V_overload setting and the maximum forward voltage, the higher the overload stress will be. The V_overload setting must be higher than Vf. Please test, program, and tune this feature for each LED load design.

Parameter Min. Typ. Max.

Notes

 

Parallel LED Protection

Overload Voltage Setting Range 47 V 56 V Set V_overload close to, but higher than the maximum LED forward voltage
Setting Tolerance -2% 2%

Protection Functions

Parameter Min. Typ. Max.

Notes

Over Temperature Protection Decreases output current, returning to normal after over temperature is removed.
Short Circuit Protection Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed.
Over Voltage Protection Limits output voltage at no load and in case the normal voltage limit fails.
Input Under  voltage Protection (IUVP) Input Protection Voltage 70 Vac 80 Vac 90 Vac Turn off the output when the input voltage falls below protection voltage.
Input Recovery Voltage 75 Vac 85 Vac 95 Vac Auto Recovery. The driver will restart when the input voltage exceeds recovery voltage.
 

 

Input Over Voltage Protection (IOVP)

Input Over Voltage

Recovery

 

310 Vac

 

320 Vac

 

330 Vac

Auto Recovery. The driver will restart when the input voltage falls below recovery voltage.
Input Over Voltage Recovery 300 Vac 310 Vac 320 Vac Auto Recovery. The driver will restart when the input voltage falls below recovery voltage.
Max. of Input Over Voltage 350 Vac The driver can survive for 8 hours with a stable input voltage stress of 350Vac.
  • Input Under Voltage Protection DiagramINVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 8
  • Input Over Voltage Protection DiagramINVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 9
  • Rotary Switch and RJ12 Connector
    Output current can be set as 0, 40%, 60%, 80%, 100% level by rotary switch and the output current can be dimmed by dimming wire in RJ12 connector when rotary switch is at ‘EXT’ position. The default mode is in ‘EXT’.INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 10

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 11

Pin

Function

1,6 Vprg
2,5 Dim+
3,4 Dim-

Dimming

  •  0-10V Dimming
    The recommended implementation of the dimming control is provided below.

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 12

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 13

Notes:

  1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
  2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener.
  3. When 0-10V negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby.
    PWM Dimming
    The recommended implementation of the dimming control is provided below.

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 14

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 15

Notes:

  1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
  2. When PWM negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby.
    Resistor Dimming
    The recommended implementation of the dimming control is provided below.

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 16

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 17

Notes:

  1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
  2. When resistor negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby.
  • Time Dimming
    Time dimming control includes 3 kinds of modes, they are Self Adapting-Midnight, Self Adapting Percentage and Traditional Timer.
    Self Adapting-Midnight: Automatically adjusts the dimming curve based on the on-time of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time.
    Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) / (programmed on-time from the dimming curve).
    Traditional Timer: Follows the programmed timing curve after power on with no changes.
  • Output Lumen Compensation
    Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation.
  • Minimum Dimming Level with 5% or 10% Selectable
    The minimum dimming level can be set as 5% or 10% by Inventronics Multi Programmer,10% is default.
  • Maximum Dimming Level with 9V or 10V Selectable
    The maximum dimming level can be set as corresponding dimming voltage is 9V or 10V by Inventronics Multi Programmer,9V is default.
  • Fade Time Adjustable
    Soft-start time and dimming slope can be adjusted by Inventronics Multi Programmer to get customized fade time experience, disable mode is default.
  • End Of Life
    End-of-Life (EOL) is providing a visual notification to a user that the LED module has reached the end of manufacturer-specified life and that the replacement is recommended. Once active, an indication is given at each power-up of the driver, which the driver indicates this through a lower light output during the first 1 minute before normal operation is continued.
  • Digital Dimming
    Inventronics Digital Dimming is a UART (Universal Asynchronous Receive Transmitter) based communication protocol. Please refer to Inventronics Digital Dimming file for details
  • Daisy Chain Application
    Daisy chain system can support synchronous dimming of up to 100 drivers due to unique dimming interface design, please pay attention to right sequence of ‘IN’ and ‘OUT’ port for RJ12 connection.

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 17

Inventronics supports daisy chain connection for drivers that is dimmed by external controller. All drivers’ rotary switch need to be tuned to ‘EXT’.
Inventronics offers the solution to use driver itself to control daisy chain dimming without the controller. The rotary switch of the master driver is tuned to required dimming level when the rest of drivers are tuned to ‘EXT’.

Programming Connection Diagram

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 19

Please refer to PRG-MUL2 (Programmer) datasheet for details.

Mechanical Outline

INVENTRONICS SUM 760S MGR Series 760W Programmable Driver with INV Digital Dimming - Derating 20

Note: This driver features UL Wet Location, IP66 panel mount connectors to streamline wiring in the field while still supporting stringent environmental conditions. The mating push-lock are not supplied by Inventronics. Please contact Wieland and Amphenol LTW or one of their suppliers for assistance sourcing the mating push-lock.

Location Series Rating voltage/current PN of connector on driver PN of mating push-lock
Vin Wieland RST20i3 600V/10A 96.032.1055.7 96.031.0055.7 (Spring) or 96.031.4055.7 (Screw)
Vo ALTW X-Lok,C-Size 300V/20A ABAB-CAQ03000100 CC-03BFMB-QL8APP

RoHS Compliance
Our products comply with reference to RoHS Directive (EU) 2015/863 amending 2011/65/EU, calling for the elimination of lead and other hazardous substances from electronic products.
Revision History

Change
Date
Rev. Description of Change
Item From To
2023-02-10 A Datasheet Release / /

Specifications are subject to changes without notice.
All specifications are typical at 25°C unless otherwise stated.

www.inventronics-co.com
Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com

Documents / Resources

INVENTRONICS SUM-760S MGR Series 760W Programmable Driver with INV Digital Dimming [pdf] Owner's Manual
SUM-760S MGR Series, 760W Programmable Driver with INV Digital Dimming, SUM-760S MGR Series 760W Programmable Driver with INV Digital Dimming, SUM-760S MGR Series 760W Programmable Driver, 760W Programmable Driver, Programmable Driver

References

Leave a comment

Your email address will not be published. Required fields are marked *