Interthings IPB203 Doorbell Camera User Guide

Interthings IPB203 Doorbell Camera User Guide

Package contents

• 1x Doorbell camera 1x Indoor chime
• 1x USB charging cable
• 1x Installation set
• 1x Reset pin
• 1x Quick Start Guide

Description

Doorbell

1. Microphone
2. Lens
3. Light sensor
4. Indicator red- charging blue – working
5. Doorbell button
6. Reset button
   • Hold and press the reset button for 3 seconds to reset the connection and delete the device from the app.
7. Speaker
8. Screw hole (for install the doorbell and wall bracket)
9. Type-C charging port

Chime

1. Indicator
2. Speaker
3. Pairing button
4. Voice +/-
5. Tune
6. USB 2.0 power connector

Before using the doorbell

1. Charge the doorbell device via a 5V(1A~2A) adaper (adapter not included) and suplied charging cable.
   While the doorbell is in charging, the charging indicator(red) will be turnned on.
   The charging indicator will be turnned of automatically while the battery is fully charged.
2. Before mounting the doorbell, use your smartphone to test if the Wi-Fi signal be covered and strong signal. Place the camera in a location with a clear, unblock field of view.

Pair the chime and doorbell

1. Plug-in the USB chime in to a 5V(1A ~2A) adapter or a USB 2.0 socket to power on the chime.
2. Hold and press the A-pair button of the chime , the indicator of the chime will be flashed which means the chime is ready to pair.
3. Press the B-ring button of the doorbell camera, the chime will receive the signal and ring, means the chime is connected to the doorbell camera.
4. Press the voice +/- button to switch the volume of the chime.
5. Press the tune button to choose your desired tune

Installation – Connect the doorbell with the app

1. Power the camera After full charge the battery, hold and press the bell button for 3 seconds to turn on the doorbell.
2. App setup and installation Use your mobile phone or tablet to search for “TuyaSmart” or “Smarties” in Google Play (for Android OS) or in the Apple app store (for iOS) to find the app, and install it according the instructions.
   
   
   TuyaSmart
   
   Smart Life
   

Register an account

‘If this is the first time using the app, you need to register an account as per below:

Note:

1. Make sure your smartphone already connected to a 2.4GHz Wi-Fi and the Bluetooth turns ON.
2. Press the ring button of the doorbell, then tap “scan” or “Smart camera(BLE)” from the app.
   Ring the bell make sure the blue indicator is blinking.

The device only works when someone rings the bell.
User will get the notification and phone call from the app.
The message center helps user to check the history of the visitors.

Warning

To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment.

FCC Statement

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.