“
Product Information
Specifications
- Product Name: INOGENI Backlit Switch Button
- Connectivity: USB, HDMI, USB-C
- Compatibility: Toggle Rooms, Toggle Rooms XT
- Power: USB-C 100W
- LED Indicator: Integrated LED for status indication
Product Usage Instructions
Installation Steps
-
- Mounting the Button:
Use an appropriate hole saw to create a hole in the table for
installation. Secure the button with the provided hardware.
-
- Connecting Terminal Block:
Use the included 4-meter or 8-meter terminal block cable to
connect the button to the Toggle Rooms or Toggle Rooms XT GPI
interface following the provided wiring diagram.
-
- Verifying Connection:
Test the connection by pressing the button to switch host
connections. The LED on the button will indicate the selected
mode.
When the button is pressed, it triggers a mode change in Toggle
Rooms or Toggle Rooms XT. The LED on the button provides visual
feedback:
- OFF: Room PC selected, Laptop not selected
- ON BLINK: Laptop selected, Room PC not selected
- Configuration Error: LED will blink in case of an incomplete
laptop host connection
FAQ
A: Check the connection between the button and the GPI
interface. Ensure all wiring is correct and securely connected.
A: Yes, you can use a CAT cable of appropriate length following
the recommended wiring standard (T-568B) for connecting to the
terminal block.
“`
Thank You!
Dear Customer,
Congratulations on the purchase of your new INOGENI product. This finely engineered solution will definitely elevate any videoconference experience. Take advantage of an entire support team to address any AV challenges you may have.
INO BUTTON KIT
BACKLIT SWITCH BUT TON WITH HARDWARE FOR TABLES INSTALLATION GUIDE
DEVICE CONNECTORS
Table top with the grommet
WHAT IS IN THE BOX
· 1x button with assembled cable with screw and nut hardware
· 1x terminal block plug
· Installation Guide · One terminal block cable. Length options:
· INO-BUTTON KIT 4 m 4 meters (12 ft) · INO-BUTTON KIT 8 m 8 meters (25 ft)
INO BUT TON KIT — BACKLIT SWITCH BUT TON WITH HARDWARE FOR TABLES
BEFORE YOU GET STARTED, ENSURE THAT ALL DRIVERS REQUIRED FOR USB DEVICE(S) ARE INSTALLED.
TYPICAL APPLICATION Here is a typical connection diagram used for the TOGGLE ROOMS or the TOGGLE ROOMS XT for larger spaces with a device in a videoconferencing setup when embedding the button on the table.
TOGGLE ROOMS
HDMI sharing content
4K60 in 16:9 5K30 in 21:9 monitor
USB HDMI HDMI
USB HDMI
USB-C
LEGEND
USB
HDMI
TOGGLE ROOMS XT
Touch panel with optional HDMI ingest
USB speakerphone
INOBUTTON KIT
Push button
Laptop hosts
for BYOM
the meeting
USB-C 100W
TOGGLE ROOMS Under the table installation
HDMI sharing content
4K60 in 16:9 5K30 in 21:9 monitor
Touch panel with optional HDMI ingest
USB speakerphone
INOBUTTON KIT
Push button for BYOM
Laptop hosts the meeting
USB-C 100W
HDMI HDMI USB HDMI USB
USB-C
TOGGLE ROOMS XT Room PC hub Behind the display installation
LEGEND
USB
HDMI
CAT6A cable extension up to 70 m (230 ft) From the main Room PC to the laptop device
TOGGLE ROOMS XT Laptop hub
Under the table installation
The button acts as a trigger to enable laptop/BYOM mode for TOGGLE ROOMS or the TOGGLE ROOMS XT.
INSTALLATION STEPS
What you’ll need for the installation:
· INO BUTTON KIT includes:
· 1x button with assembled cable with screw and nut hardware
· 1x terminal block plug
· 1x Installation Guide
· One terminal block cable. Length options:
· INO-BUTTON KIT 4 m
4 meters (12 ft)
· INO-BUTTON KIT 8 m
8 meters (25 ft)
· INOGENI TOGGLE ROOMS or TOGGLE ROOMS XT
· 57 mm [2¼ in] hole saw with drilling kit
· Flat screwdriver
· Category (CAT) cable with the length needed
Here are the instructions for the installation: 1. Drill a 2¼ in [57 mm] hole into the table using the
appropriate hole saw. You can then mount the screw through the table. Screw the nut under the table counterclockwise.
ø 57 mm [2 1/4 in]
Table
2. Use the included 4-meter (12 ft) or 8-meter (25 ft) mounted terminal block cable, or do it yourself with a CAT cable of the appropriate length and connect the terminal block to the CAT conductors according to the TOGGLE ROOMS GPI connection. Here is a recommended connection using the T-568B standard with a CAT cable.
TOGGLE ROOMS
CAT cable
VOUT GND
1
VOUT GND
1
TOGGLE ROOMS XT – Laptop hub
CAT cable
VOUT GND
1
VOUT GND
1
INO BUT TON KIT — BACKLIT SWITCH BUT TON WITH HARDWARE FOR TABLES
TOGGLE ROOMS XT – Room PC hub
CAT cable
VOUT GND
1
VOUT GND
1
Button connector
TOGGLE ROOMS
GPI connector
TOGGLE ROOMS XT
GPI connector
CAT signal T-568B
Signal description
VOUT 1
VOUT 1
VOUT 1
Solid green
Solid blue
Solid orange
+5V voltage supply for LED
Ground
Normally open contact
N/A
N/A
N/A
N/A N/A
3. Connect both terminal block connectors to the button cable and the TOGGLE ROOMS or the TOGGLE ROOMS XT GPI interface.
4. To verify if the connection is successful, click the button to switch the host connection. The button will light up to indicate that the TOGGLE ROOMS or the TOGGLE ROOMS XT selected the laptop connection.
BUTTON AND LED BEHAVIOR
When the user presses the button, it will trigger TOGGLE ROOMS or the TOGGLE ROOMS XT to change the current mode. The button has an integrated LED and will light up when the laptop is selected.
Button LED
Signal description
OFF
Room PC selected. Laptop NOT selected.
ON BLINK
Laptop selected. Room PC NOT selected.
Configuration error For example: LED wil blink if selected laptop host (USB + video) incomplete.
CERTIFICATION, COMPLIANCE AND WARRANTY I N F O R M AT I O N
CE Statement We, INOGENI Inc., declare under our sole responsibility that the INO BUTTON KIT, to which this declaration relates, is in conformity with European Standards EN 55032, EN 55035, and RoHS Directive 2011/65/EU + 2015/863/EU.
UKCA Statement This device is compliant with the Electromagnetic Compatibility Regulations 2016 No. 1091 as part of the requirements leading to the UKCA marking.
To learn more, visit the product page at www.inogeni.com/product/ino-button-kit
For technical support, contact us at support@inogeni.com
INOGENI 1045 Wilfrid-Pelletier Avenue Suite 101 Québec City, QC G1W 0C6, Canada +1 418 651 3383
Copyright © 2024/10 INOGENI | All Rights Reserved. INOGENI name and logo are trademarks or registered trademarks of INOGENI. Use of this product is subject to the terms and conditions of the license and limited warranty in effect at the time of purchase. Product specifications can change without notice.
Documents / Resources
 |
INOGENI Ino Button Kit [pdf] Instructions Ino Button Kit, Button Kit, Kit |
