SIMREP ENGINEERING D1 V10 Mepee Wheel Tinye na akwụkwọ ntuziaka ntuziaka

Nzọụkwụ 2:
Gbanye D1 V1.0 n'azụ wiil ahụ wee kwado oghere mkpuchi na mkpuchi ihu Plexiglas. Jiri aka tinye bolts hex M3x10mm. Jiri eriri hex oghere 2mm kechie skru ndị ahụ n'usoro n'usoro. ỊDỌ AKA NA NTỊ: Imebiga ihe mgbochi ahụ nwere ike ibute mmebi.

Nzọụkwụ 3:
Jikọọ eriri USB 2.0 na ọdụ ụgbọ USB gị na kọmputa gị.

Nwụnye ngwanrọ:
Iji jikọọ TM OpenWheel Add-On na SimHub maka oge mbụ, soro usoro ndị a:

Nzọụkwụ 1:
Pịa na ibe Arduino n'akụkụ aka ekpe (Ekepụtara RED).

Nzọụkwụ 2:
Gaa na taabụ ngwaike m dị n'akụkụ aka nri wee pịa Single Arduino.

Nzọụkwụ 3:
Chere ka SimHub mechaa nyocha maka Ngosipụta TM Open Wheel Add-on D1 V1.0. O kwesịrị ịsị ejikọrọ. Ọ bụrụ na ọ bụghị, biko rụtụ aka na ngalaba nchọpụta nsogbu n'okpuru.

Nzọụkwụ 4:
Ọ bụrụ na ị zutere nsogbu ọ bụla ma ọ bụ degharịa ngwanro na mberede, ị nwere ike ịtọgharịa ntọala ahụ. N'ime ngwa nhazi, họrọ Arduino Pro Micro (ATmega32u4). Tinye LED (WS2812B) na ngosi. Lelee ma ọ bụrụ na eserese ntụtụ niile ziri ezi, wee lelee igbe ahụ wee kụọ UPLOAD TO ARDUINO.

Nzọụkwụ 5:
Laghachi na taabụ akpọrọ Ihuenyo, n'elu aka ekpe. Wee pịa New ihuenyo.

Nzọụkwụ 6:
Ibe ọhụrụ ga-apụta. Pịa na ala na ADD.

Nzọụkwụ 7:
Ugbu a tọọ aha ahụ na SRE maka ihuenyo na-adịghị arụ ọrụ:

Dee SRE na aha ihuenyo (n'elu aka ekpe)
Lelee igbe a na-akpọ Idle screen (n'okpuru aha ihuenyo)
Dee SRE iji gosi ederede (n'etiti aka nri)
Pịa Chekwa (n'ala aka nri)

Ihuenyo ọhụrụ gị ga-egosi na ala na taabụ ihuenyo.
Debe ihuenyo n'elu ibe site na ịpị aka ekpe wee dọrọ ya n'elu. Mgbe ịdọrọ, ihuenyo matriks gị kwesịrị igosipụta SRE. Ọ bụrụ na ọ bụghị, lelee ma ọ bụrụ na ejikọrọ ihe ngosi gị na SimHub n'okpuru taabụ My Hardware ma megharịa usoro ahụ.

Ajụjụ:

Kedu ka m ga-esi kpọtụrụ ndị ahịa?
Ị nwere ike ịkpọtụrụ anyị na: service@simrep-engineering.com
Kedu ihe m ga-eme ma ọ bụrụ na m kpuchiri bolts n'oge echichi?
Ịmefe ihe mgbochi ahụ nwere ike ibute mmebi. Biko kpachara anya mgbe ị na-emesi ike ma hụ na ịghara imechi ha.

Kedu ngwa ngwa dakọtara na ihe ngosi TM OpenWheel Add-On?
Ngosipụta ahụ na-arụ ọrụ na ngwanrọ SimHub. Gbaa mbọ hụ na etinyere ya tupu ịmalite nrụnye.
Kedu otu m ga-esi tọgharịa ntọala ma ọ bụrụ na m degharịa ngwanro na mberede?
N'ime ngwa nhazi, họrọ Arduino Pro Micro (ATmega32u4). Tinye LED (WS2812B) na ngosi. Lelee ma ọ bụrụ na eserese ntụtụ niile ziri ezi, wee lelee igbe ahụ wee kụọ UPLOAD TO ARDUINO.

Ngosipụta mgbakwunye OpenWheel TM V1.1 ntuziaka nwụnye

Daalụ maka ịzụrụ
Daalụ maka ịzụrụ n'aka anyị!
Anyị nwere olileanya na ị ga-anụ ụtọ ngwaahịa a, ọ bụrụ na ị nwere ajụjụ ọ bụla, biko kpọtụrụ anyị na: service@simrep-engineering.com

Ọdịnaya ngwugwu

1x Ihe mgbakwunye D1 V1.0 ihuenyo
1 x Plexiglass ihu ihu
4 x M3x10mm nkenke
1x2mm hex soket kwa

Ngwa ngwa

Ejiri ngwa ngwa SimHub hazie ngwaahịa a. Iji jiri ngwaahịa a, SimHub ga-arụnye ma nwee ike ibudata ya na: https://www.simhubdash.com/
Ngwaahịa a na-abịa na pro ndabara 2filebụ otu maka ụgbọ ala wheel mepere emepe na otu maka ụgbọ ala GT. Profiles nwere ike ibudata na gị websaịtị na-eziga mgbe ugwo nkwenye.
Enwere ike ịhazi D1 V1.0 dịka mmasị ndị ọrụ na SimHub ma ọ bụ ngwanrọ ọzọ. Ọ bụrụ na akụkụ ndị na-efu efu na/ma ọ bụ mebiri emebi, biko kpọtụrụ nkwado ndị ahịa anyị na: service@simrep-engineering.com

Ntinye ngwaike

Ịwụnye ihe ngosi n'aka onye ọrụ ntụkwasị obi gị TM OpenWheel steering.

Nzọụkwụ 1
Wepu ihe mkpuchi Thrustmaster site na iji mgbanaka oghere hex 2mm. (gụnyere). Wepu mkpuchi nke akara na RED.

Nzọụkwụ 2
Gbanye D1 V1.0 n'azụ wiil ahụ wee kwado oghere mkpuchi na mkpuchi ihu Plexiglas. Jiri aka tinye bolts hex M3x10mm. Jiri eriri hex oghere 2mm kechie skru ndị ahụ n'usoro n'usoro.

Ịdọ aka ná ntị !! Imechi ihe mgbochi ahụ nwere ike ibute mmebi

Nzọụkwụ 3
Jikọọ eriri USB 2.0 na ọdụ ụgbọ USB gị na kọmputa gị.

gafereview nke Ngosipụta

A ngwa ngwa gafereview nke ngosi na anya na matriks views na nọmba LED.
View A - ihuenyo na-adịghị arụ ọrụ - ka egosiri ebe a View C nwere gia 2 ahọpụtara dị ka example. A kọwara nke a na ndepụta ọrụ GT na OpenWheel.

Ọrụ OpenWheel ezighi ezi

Nke a bụ pro ndabarafile nke nwere ike ibunye ngwa ngwa na SimHub dị ka anyị ga-akọwa na usoro ndị a.

Matrix na-arụ ọrụ

View A - IDLE enweghị egwuregwu na-agba ọsọ, akara SimRep Engineering (SRE).
View B - Ihe ngosi ọsọ, nke a bụ ndabara view na egwuregwu.

View C - Ihe ngosi Gear, nke a na-egosipụta mgbe niile n'etiti brackets ([]).
View D - Ihe ngosi ụlọ nyocha, nke a ga-ebu ụzọ gosipụta 'LAB' wee soro nọmba ụlọ nyocha dị ugbu a.

Ọrụ ntị aka ekpe (LED 1 ruo 6)

LED 1. Ụgbọ ala aka ekpe (Ọcha na-egbu maramara)
LED 2. DRS agbanyere (Green blinking)
LED 2. DRS dị (Orange static)
LED 3. Mmanụ (Green 100%, oroma 50%, red blink 15%)

LED 4. All flags
LED 5. All flags
LED 6. Oge delta mwepu

Ọrụ ntị aka nri (LED 21 ruo 26)

LED 21. Delta oge niile (Green delta +, red delta -)
LED 22. All flags
LED 23. All flags
LED 24. Mmanụ (Green 100%, oroma 50%, red blink 15%)
LED 25. DRS agbanyere (Green blinking)
LED 25. DRS dị (Orange static)
LED 26. Ụgbọ ala aka nri (Ọcha blink)

Ọrụ ndị isi eduzi (7 ruo 20)

Ngosipụta ihe mgbochi RPM na PIT

Ngosipụta ọkọlọtọ
LED 4, 5, 22 na 23 na-egosipụta ọkọlọtọ, nke egosiri dị ka ndị a:

Ọkọlọtọ akwụkwọ ndụ akwụkwọ ndụ na (acha ndụ ndụ na-agba ọsọ ọsọ)
Ọkọlọtọ na-acha odo odo na (edo edo na-adị nwayọọ)
Ọkọlọtọ na-acha anụnụ anụnụ na (acha anụnụ anụnụ na-adị nwayọọ)
Ọkọlọtọ ojii na (na-acha ọcha na-agba ọsọ ọsọ)
Ọkọlọtọ ọcha na (na-acha ọcha na sekọnd ise ọ bụla)

Nwụnye ngwanrọ

Jikọọ TM OpenWheel Tinye-On na SimHub maka oge mbụ.
Dịka e kwuru na mbụ, ihe ngosi ahụ na-arụ ọrụ na ngwanrọ SimHub, yabụ gbaa mbọ hụ na etinyere nke ahụ tupu ịga n'ihu.

Nzọụkwụ 1
Pịa na ibe "Arduino" n'akụkụ aka ekpe (Ekepụtara RED).

Nzọụkwụ 2
Gaa na taabụ "ngwaike m" na akuku aka nri wee pịa "Single Arduino".

Nzọụkwụ 3
Chere ka SimHub mechaa nyocha maka Ngosipụta TM Open Wheel Add-on D1 V1.0
O kwesịrị ịsị ejikọrọ.
Ọ bụrụ na ọ bụghị, biko rụtụ aka na ngalaba nchọpụta nsogbu n'okpuru.

Emeelarị usoro a na mmepụta, mana ọ bụrụ na ị nwere nsogbu ma ọ bụ acidentaly degharịa sọftụwia ị nwere ike ịtọgharịa ntọala dị ka nke a.
N'ime ngwá ọrụ nhazi, họrọ "Arduino Pro Micro (ATmega32u4)
Ugbu a, anyị nwere ike ịgbakwunye LED (WS2812B)

Ọ bụrụ na egosiri ihe niile ziri ezi, lelee igbe ahụ wee kụọ “Bulite TO ARDUINO”

Nzọụkwụ 4
Laghachi na taabụ a na-akpọ "ihuenyo", n'elu aka ekpe.
Wee pịa "New screen"

Nzọụkwụ 5
Ibe ọhụrụ ga-apụta.
Pịa na ala na "ADD"

Nzọụkwụ 6
Ugbu a tọọ aha ahụ na SRE maka ihuenyo na-adịghị arụ ọrụ.

Dee "SRE" na "aha ihuenyo" (n'elu aka ekpe)
Lelee igbe a na-akpọ "Idle Idle" (n'okpuru aha ihuenyo)
Dee "SRE" ka ọ bụrụ "Gosi ederede" (n'etiti aka nri)
Pịa na "Chekwa" (n'ala aka nri)

Nzọụkwụ 7
Ihuenyo ọhụrụ gị ga-egosi na ala na taabụ "ihuenyo". Debe ihuenyo n'elu ibe site na ịpị aka ekpe wee dọrọ ya n'elu. Mgbe ịdọrọ, ihuenyo matriks gị kwesịrị igosi "SRE".
Ọ bụrụ na ọ bụghị, lelee ma ọ bụrụ na ejikọrọ ihe ngosi gị na SimHub n'okpuru taabụ "My Hardware" ma megharịa usoro ahụ.

Nzọụkwụ 8
Pịa ọzọ na "Ihuenyo ọhụrụ"

Nzọụkwụ 9

Gbanwee "aha ihuenyo" ka ọ bụrụ "Ọsọ na ngwa"
Lelee igbe ahụ "n'ihuenyo egwuregwu"
Pịa "ADD"
Pịa “ederede agbakọrọ”
Pịa "Dezie"

Nzọụkwụ 10

Pịa "Uru agbakọrọ"
Detuo na mado usoro NCalc ndị a n'ime igbe ederede
ma ọ bụrụ na (gbanwere (750, [DataCorePlugin.GameData.NewData.Gear]) ma ọ bụ [DataCorePlugin.GameData.NewData.SpeedKmh] <1, '[' + [DataCorePlugin.GameData.NewData.Gear] + ']', usoro ([[). DataCorePlugin.GameData.NewData.SpeedKmh],'0′))
Pịa "OK"

Nzọụkwụ 11
Pịa "Chekwa" na ala aka nri.

Nzọụkwụ 12
Dọrọ ihuenyo site na ala ruo ọnọdụ nke abụọ n'okpuru ihuenyo SRE.

A na-eme akụkụ siri ike
Nhazi maka Matrix ugbu a emechaala
Ọ bụ naanị RGB led profile iga!

Nzọụkwụ 13
Na-ebubata LED profile

Gaa na taabụ "RGB LEDs"
Pịa na "import profile”
Tinye ya files “Egwuregwu ọ bụla – TM Mepee Wheel Tinye-Ngosipụta GT V1.0.ledsprofile"Na" Egwuregwu ọ bụla - TM Open Wheel Tinye-On Ngosipụta Ụdị V1.0.ledsprofile" site na kọmputa gị.
Ị nwere ike ibuzi otu n'ime ha abụọ files dabere na mmasị klaasị gị, a kọwara ihe dị iche na mmalite nke akwụkwọ ntuziaka.

Biko rụba ama: Onye GT profile na-akwado ABS na TC nọ n'ọrụ. Formula profile na-akwado DRS dị yana arụ ọrụ.

Nzọụkwụ 14
Emeela ihe niile!
Gaa na taabụ "Egwuregwu" n'akụkụ aka ekpe nke SimHub, họrọ egwuregwu gị, ka agbụrụ ahụ malite!
Daalụ maka ịzụrụ na ịkwado azụmahịa anyị! Anyị na-aga n'ihu na-emeziwanye ngwaahịa na ọrụ anyị. Ọ bụrụ na ị nwetara nsogbu ọ bụla n'oge echichi, biko mee ka anyị mara site na ịkpọtụrụ anyị na service@simrep-engineering.com ma ọ bụ izipu DM na Ins anyịtagram profile www.nwetagram.com/simrep_engineering.

Nchọpụta nsogbu

Enweghị njikọ na SimHub - biko hụ na etinyere eriri USB A. Ọ bụrụ na ị na-eji eriri USB ma ọ bụ ihe ndọtị, biko jikọọ ngosi ozugbo na ọdụ ụgbọ USB na kọmputa.
Kọmputa m enweghị ike ịmata ihe ngosi TM OpenWheel - Nke a nwere ike ịpụta na ị tinyebeghị SimHub, ma ọ bụ SimHub etinyeghị gị ọkwọ ụgbọala ziri ezi. Iji aka tinye ihe ndị a gaa na: https://www.arduino.cc/en/software, budata ma wụnye ngwa ngwa Arduino IDE.

Ederede IDLE agaghị egosi na ngosipụta matriks - Biko hụ na ị gbasoro usoro niile wee tinye ihe ngosi SRE ọhụrụ. Mgbe agbakwunyere, ọ dị mkpa ka ịlele ya dị ka ihuenyo IDLE naanị. Ngosipụta kwesịrị ịdị n'elu taabụ "ihuenyo" dịka nzọụkwụ 7 si dị.
Enweghị m onye ndu ọ bụlafiles ibubata – ị kwesịrị ịnata ha na .zip ma ọ bụ .rar file na email gị. Imepe .rar ị nwere ike iji winrar. Ọ bụrụ na ịnataghị nke ọma files, biko kpọtụrụ anyị na service@simrep-engineering.com

Akwụkwọ / akụrụngwa

SIMREP ENGINEERING D1 V10 Mepee Wheel Tinye Na Ngosipụta [pdf] Akwụkwọ ntuziaka
D1 V10 Mepee Wheel Tinye Na Ngosipụta, D1 V10, Mepee Wheel Tinye Na Ngosipụta, Tinye Wheel Na Ngosipụta, Ngosipụta

Ntụaka

Akwụkwọ ntuziaka onye ọrụ

SIMREP ENGINEERING D1 V10 Mepee Wheel Tinye Na Ngosipụta